Hydrocarbon Refrigerant Vaporization Inside a Brazed Plate Heat Exchanger

2012 ◽  
Vol 134 (10) ◽  
Author(s):  
Giovanni A. Longo
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Saturation Temperature ◽  
Transfer Coefficients ◽  
Frictional Pressure Drop ◽  
Heat Transfer Coefficients ◽  
Experimental Heat ◽  
Fluid Properties

This paper presents the experimental heat transfer coefficients and pressure drop measured during HC-600a (isobutane), HC-290 (propane), and HC-1270 (propylene) vaporization inside a brazed plate heat exchanger (BPHE): the effects of heat flux, refrigerant mass flux, saturation temperature (pressure), evaporator outlet condition, and fluid properties are investigated. The experimental tests include 172 vaporization runs carried out at three different saturation temperatures (10, 15, and 20 °C) and four different evaporator outlet conditions (outlet vapor quality around 0.80 and 1.00, outlet vapor super-heating around 5 and 10 °C). The refrigerant mass flux ranges from 6.6 to 23.9 kg m−2 s−1 and the heat flux from 4.3 to 19.6 kW m−2. The heat transfer and pressure drop measurements have been complemented with IR thermography analysis in order to quantify the portion of the heat transfer surface affected by vapor super-heating. The heat transfer coefficients show great sensitivity to heat flux, evaporator outlet condition and fluid properties and weak sensitivity to saturation temperature (pressure). The frictional pressure drop shows a linear dependence on the kinetic energy per unit volume of the refrigerant flow and therefore a quadratic dependence on refrigerant mass flux. HC-1270 exhibits heat transfer coefficients 6–12% higher than HC-290 and 35–50% higher than HC-600a and frictional pressure drops 5–10% lower than HC-290 and 60% lower than HC-600a. The experimental heat transfer coefficients are compared with two well-known correlations for nucleate boiling and a linear equation for frictional pressure drop is proposed.

Heat Transfer and Pressure Drop During Hydrocarbon Refrigerant Vaporisation Inside a Brazed Plate Heat Exchanger

2010 ◽  
Author(s):  
Giovanni A. Longo
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Saturation Temperature ◽  
Transfer Coefficients ◽  
Frictional Pressure Drop ◽  
Heat Transfer Coefficients ◽  
Experimental Heat ◽  
Fluid Properties

This paper presents the experimental heat transfer coefficients and pressure drop measured during HC-600a (Isobutane), HC-290 (Propane) and HC-1270 (Propylene) vaporisation inside a small brazed plate heat exchanger: the effects of heat flux, refrigerant mass flux, saturation temperature (pressure), outlet conditions and fluid properties are investigated. The experimental tests include 172 vaporisation runs carried out at three different saturation temperatures: 10, 15 and 20°C. The refrigerant mass flux ranges from 6.6 to 23.9 kg/m2s and the heat flux from 4.3 to 19.6 kW/m2. The heat transfer coefficients show great sensitivity to heat flux, outlet conditions and fluid properties and weak sensitivity to saturation temperature (pressure). The frictional pressure drop shows a linear dependence on the kinetic energy per unit volume of the refrigerant flow and therefore a quadratic dependence on refrigerant mass flux. HC-1270 shows heat transfer coefficients 6–12% higher than HC-290 and 35–50% higher than HC-600a and frictional pressure drops 5–10% lower than HC-290 and 2.5 time lower than HC-600a. The experimental heat transfer coefficients are compared with two well-known equations for nucleate boiling and a correlation for frictional pressure drop is proposed.

Forced Convective Boiling of Refrigerant HCFC123 in a Mini-Tube

2010 ◽  
Author(s):  
Koichi Araga ◽  
Keisuke Okamoto ◽  
Keiji Murata
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Mass Flux ◽  
Pool Boiling ◽  
Constant Heat Flux ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Convective Boiling ◽  
Frictional Pressure Drop ◽  
Heat Transfer Coefficients

This paper presents an experimental investigation of the forced convective boiling of refrigerant HCFC123 in a mini-tube. The inner diameters of the test tubes, D, were 0.51 mm and 0.30 mm. First, two-phase frictional pressure drops were measured under adiabatic conditions and compared with the correlations for conventional tubes. The frictional pressure drop data were lower than the correlation for conventional tubes. However, the data were qualitatively in accord with those for conventional tubes and were correlated in the form φL2−1/Xtt. Next, heat transfer coefficients were measured under the conditions of constant heat flux and compared with those for conventional tubes and for pool boiling. The heat transfer characteristics for mini-tubes were different from those for conventional tubes and quite complicated. The heat transfer coefficients for D = 0.51 mm increased with heat flux but were almost independent of mass flux. Although the heat transfer coefficients were higher than those for a conventional tube with D = 10.3 mm and for pool boiling in the low quality region, they decreased gradually with increasing quality. The heat transfer coefficients for D = 0.30 mm were higher than those for D = 0.51 mm and were almost independent of both mass flux and heat flux.

Experimental Investigation of Condensation Heat Transfer and Adiabatic Pressure Drop Characteristics Inside a Microfin and Smooth Tube

2017 ◽  
Vol 25 (03) ◽  
pp. 1750027 ◽  
Author(s):  
M. Mostaqur Rahman ◽  
Keishi Kariya ◽  
Akio Miyara
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Saturation Temperature ◽  
Condensation Heat Transfer ◽  
Vapor Quality ◽  
Transfer Coefficients ◽  
Frictional Pressure Drop

Experiments on condensation heat transfer and adiabatic pressure drop characteristics of R134a were performed inside smooth and microfin horizontal tubes. The tests were conducted in the mass flux range of 50[Formula: see text]kg/m2s to 200[Formula: see text]kg/m2s, vapor quality range of 0 to 1 and saturation temperature range of 20[Formula: see text]C to 35[Formula: see text]C. The effects of mass velocity, vapor quality, saturation temperature, and microfin on the condensation heat transfer and frictional pressure drop were analyzed. It was discovered that the local heat transfer coefficients and frictional pressure drop increases with increasing mass flux and vapor quality and decreasing with increasing saturation temperature. Higher heat transfer coefficient and frictional pressure drop in microfin tube were observed. The present experimental data were compared with the existing well-known condensation heat transfer and frictional pressure drop models available in the open literature. The condensation heat transfer coefficient and frictional pressure drop of R134a in horizontal microfin tube was predicted within an acceptable range by the existing correlation.

Local Heat Transfer Coefficients and Pressure Drop During Evaporation in a Smooth Horizontal Tube

2002 ◽  
Author(s):  
C. Aprea ◽  
A. Greco ◽  
G. P. Vanoli
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Local Heat Transfer ◽  
Horizontal Tube ◽  
Local Heat ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

R22 is the most widely employed HCFC working fluid in vapour compression plant. HCFCs must be replaced within 2020. Major problems arise with the substitution of the working fluids, related to the decrease in performance of the plant. Therefore, extremely accurate design procedures are needed. The relative sizing of each of the components of the plant is crucial for cycle performance. For this reason, the knowledge of the new fluids heat transfer characteristics in condensers and evaporators is required. The local heat transfer coefficients and pressure drop of pure R22 and of the azeotropic mixture R507 (R125-R143a 50%/50% in weight) have been measured during convective boiling. The test section is a smooth horizontal tube made of a with a 6 mm I.D. stainless steel tube, 6 m length, uniformly heated by Joule effect. The effects of heat flux, mass flux and evaporation pressure on the heat transfer coefficients are investigated. The evaporating pressure varies within the range 3 ÷10 bar, the refrigerant mass flux within the range 200 ÷ 1000 kg/m2s, the heat flux within 0 ÷ 44 kW/m2. A comparison have been carried out between the experimental data and those predicted by means of the most credited literature relationships.

An Experimental Investigation of Condensation Heat Transfer Coefficients and Pressure Drops of Refrigerants Inside Multiport Mini-channel Tubes

2017 ◽  
Vol 25 (02) ◽  
pp. 1750013 ◽  
Author(s):  
Pham-Quang Vu ◽  
Kwang-Il Choi ◽  
Jong-Taek Oh ◽  
Honggi Cho
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Condensation Heat Transfer ◽  
Working Fluid ◽  
Vapor Quality ◽  
Transfer Coefficients ◽  
Pressure Drops ◽  
Heat Transfer Coefficients

The condensation heat transfer coefficients and pressure drops of R410A and R22 flowing inside a horizontal aluminum multiport mini-channel tube having 18 channels are investigated. Experimental data are presented for the range of vapor quality from 0.1 to 0.9, mass flux from 50 to 500[Formula: see text]kg/m2s, heat flux from 3 to 15[Formula: see text]kW/m2 and the saturation temperature at 48[Formula: see text]C. The pressure drop across the test section was directly measured by a differential pressure transducer. At a small scale, the noncircular cross-sections can enhance the effect of the surface tension. The average heat transfer coefficient increased with the increase of vapor quality, mass flux and heat flux. Under the same test conditions, the heat transfer coefficients of R22 are higher than those for R410A, the pressure drops for R410A are 7–19% lower than those of R22. The lower pressure drop of R410A has an important advantage as an alternative working fluid for R22 in air-conditioning and heat pump systems.

Evaporative Heat Transfer and Pressure Drop of CO2 in a Microchannel Tube

2005 ◽  
Author(s):  
Siyoung Jeong ◽  
Eunsang Cho ◽  
Hark-koo Kim
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Dry Out ◽  
The Heat Transfer Coefficient

Evaporation heat transfer and pressure drop characteristics of carbon dioxide were investigated in a multi-channel micro tube. The aluminum tube has 3 square channels with a hydraulic diameter of 2mm, a wall thickness of 1.5mm, and a length of 5m. The tube was heated directly by electric current. Experiments were conducted at heat fluxes ranging 4–16 kW/m2, mass fluxes from 150 to 750 kg/m2s, evaporative temperature from 0 to 10°C, and qualities from 0 to superheated state. The heat transfer coefficient measured was in the range of 6–15kW/m2K, and the pressure drop was 3–23kPa/m. For the qualities lower than 0.5, the heat transfer coefficient was found to increase with the quality, which is assumed to be the effect of convective boiling. For the qualities higher than 0.6, sudden drop in heat transfer coefficients was sometimes observed due to local dry-out. It was found that dry-out occurred at lower quality if mass flux was smaller. The average heat transfer coefficient was found to increase with increasing heat flux, mass flux, and evaporation temperature, of which the effect of heat flux was the greatest. At given experimental conditions the pressure drop increased almost linearly with increasing quality. The total pressure drop was found to increase with increasing heat flux, mass flux, and evaporation temperature, of which the effect of mass flux was the greatest. From the experimental results simple correlations for heat transfer coefficients and pressure drop were developed.

scholarly journals Condensation Heat Transfer of R-407C in Helical Coiled Tube Heat Exchanger

Processes ◽  
2020 ◽  
Vol 8 (9) ◽  
pp. 1157
Author(s):  
Hamad Mohammad AlHajeri ◽  
Abdulrahman Almutairi ◽  
Mohamad Hamad Al-Hajeri ◽  
Abdulrahman Alenezi ◽  
Rashed ALajmi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Mass Flux ◽  
Saturation Temperature ◽  
Heat Fluxes ◽  
Transfer Coefficients ◽  
Tube Heat Exchanger ◽  
Heat Transfer Coefficients ◽  
The Relationship

The results of an experimental study to evaluate the characteristics of R-407C thermofluid during condensation in a helically coiled copper tube heat exchanger are presented. The effects of saturation temperature (Tsat), and mass and heat fluxes of refrigerant R-407C on thermal performance and pressure drop were determined. The relationship between the refrigerant wall subcooling and heat transfer coefficients was also investigated. This paper reports the effect of the temperature of the water used as cooling medium on the heat transfer rate of condensing R-407C. The study was conducted with mass flux of R-407C in the range of 100–450 kg/m2s, mass flux of the coolant water in the range of 500–5000 kg/m2s and Tsat of 31 °C, 35 °C, and 39 °C. Compared with a straight smooth tube, the use of the helical coiled (helicoidal) tube increased the condensation rate with a corresponding pressure drop that depended on the value of Tsat of the refrigerant and temperature of the coolant.

Heat Transfer and Pressure Drop Characteristics for HFE-7100 Within Microchannel Heat Sinks

2009 ◽  
Author(s):  
Chun-Min Huang ◽  
Yeau-Ren Jeng ◽  
Kai-Shing Yang ◽  
Chi-Chuan Wang ◽  
Yu-Lieh Wu
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Mass Flux ◽  
Flow Reversal ◽  
Dielectric Fluid ◽  
Vapor Quality ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Square Configuration

This study examines the heat transfer and pressure drop characteristics of the dielectric fluid HFE-7100 within multiport microchannel heat sink having a square configuration rectangular with a hydraulic diameter of 460 μm. For a lower mass flux of 100 or 200 kg/m2·s, it is found that the heat transfer coefficients are roughly independent of heat flux and vapor quality provided that no flow reversal occurs. However, with the presence of flow reversal at an elevated heat flux, appreciable drop of heat transfer coefficient is encountered. The flow reversal also plays a significant role in the overall pressure drop. Without flow reversal, the pressure drop for higher heat flux always exceeds that of lower heat flux due to acceleration contribution. However, the presence of flow reversal may offset the contribution of acceleration and results in a negligible effect of heat flux. For a higher mass flux like 300 kg/m2·s, the heat transfer coefficients are virtually independent of vapor quality and heat flux.

Flow Boiling Heat Transfer, Pressure Drop, and Flow Pattern for CO2 in a 3.5mm Horizontal Smooth Tube

2009 ◽  
Vol 131 (9) ◽  
Author(s):  
Chang Yong Park ◽  
Pega Hrnjak
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Flow Boiling Heat Transfer

Abstract C O 2 flow boiling heat transfer coefficients and pressure drop in a 3.5mm horizontal smooth tube are presented. Also, flow patterns were visualized and studied at adiabatic conditions in a 3mm glass tube located immediately after a heat transfer section. Heat was applied by a secondary fluid through two brass half cylinders to the test section tubes. This research was performed at evaporation temperatures of −15°C and −30°C, mass fluxes of 200kg∕m2s and 400kg∕m2s, and heat flux from 5kW∕m2 to 15kW∕m2 for vapor qualities ranging from 0.1 to 0.8. The CO2 heat transfer coefficients indicated the nucleate boiling dominant heat transfer characteristics such as the strong dependence on heat fluxes at a mass flux of 200kg∕m2s. However, enhanced convective boiling contribution was observed at 400kg∕m2s. Surface conditions for two different tubes were investigated with a profilometer, atomic force microscope, and scanning electron microscope images, and their possible effects on heat transfer are discussed. Pressure drop, measured at adiabatic conditions, increased with the increase of mass flux and quality, and with the decrease of evaporation temperature. The measured heat transfer coefficients and pressure drop were compared with general correlations. Some of these correlations showed relatively good agreements with measured values. Visualized flow patterns were compared with two flow pattern maps and the comparison showed that the flow pattern maps need improvement in the transition regions from intermittent to annular flow.

Two-Phase Pressure Drop and Boiling Heat Transfer in a Single Horizontal Microchannel

2006 ◽  
Author(s):  
Cheol Huh ◽  
Moo Hwan Kim
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Local Flow ◽  
Heat Transfer Coefficients ◽  
Phase Pressure

With a single microchannel and a series of microheaters made with MEMS technique, two-phase pressure drop and local flow boiling heat transfer were investigated using deionized water in a single horizontal rectangular microchannel. The test microchannel has a hydraulic diameter of 100 μm and length of 40 mm. A real time observation of the flow patterns with simultaneous measurement are made possible. Tests are performed for mass fluxes of 90, 169, and 267 kg/m2s and heat fluxes of from 100 to 600 kW/m2. The experimental local flow boiling heat transfer coefficients and two-phase frictional pressure gradient are evaluated and the effects of heat flux, mass flux, and vapor qualities on flow boiling are studied. Both the evaluated experimental data are compared with existing correlations. The experimental heat transfer coefficients are nearly independent on mass flux and the vapor quality. Most of all correlations do not provide reliable heat transfer coefficients predictions with vapor quality and prediction accuracy. As for two-phase pressure drop, the measured pressure drop increases with the mass flux and heat flux. Most of all existing correlations of two-phase frictional pressure gradient do not predict the experimental data except some limited conditions.

Sign in / Sign up

Export Citation Format

Share Document