Experimental Evaluation of Separation Methods for a Riser Dilution Approach to Dual Density Drilling

2011 ◽  
Vol 133 (3) ◽  
Author(s):  
John Shelton ◽  
John Rogers Smith ◽  
Anuj Gupta
Keyword(s):  
Drilling Fluid ◽  
Feed Stream ◽  
Separation System ◽  
Electrical Stability ◽  
Qualitative Comparison ◽  
Deepwater Drilling ◽  
Drilling System ◽  
The Stability ◽  
Dual Gradient ◽  
Laboratory Centrifuge

A dual gradient, deepwater drilling system based on dilution of riser mud requires economically separating the riser mud into a low density dilution fluid and a higher density drilling fluid. This study investigated the practicality of accomplishing this separation using hydrocyclones and centrifuges and examined the possible benefits and efficiency of each. The separation experiments were conducted using a laboratory centrifuge and 2 in. hydrocyclones. The laboratory centrifuge was able to separate the riser mud into near ideal densities for dilution and drilling fluid. However, the dense slurry retained in the centrifuge had lower electrical stability than the feed stream. The hydrocyclones achieved much less contrast in density between the low and high density discharges, but their use consistently resulted in a beneficial increase in the stability of the mud emulsion in all of the flow streams and gave more desirable rheological properties. A qualitative comparison indicates that the hydrocyclone separation system may offer a feasible and desirable alternative to a centrifuge separation system.

Experimental Evaluation of Separation Methods for a Riser Dilution Approach to Dual Density Drilling

2009 ◽  
Author(s):  
John Shelton ◽  
John Rogers Smith ◽  
Anuj Gupta
Keyword(s):  
Emulsion Stability ◽  
Drilling Fluid ◽  
Feed Stream ◽  
Separation System ◽  
Qualitative Comparison ◽  
Deepwater Drilling ◽  
Drilling System ◽  
The Stability ◽  
Dual Gradient ◽  
Laboratory Centrifuge

A dual gradient, deepwater drilling system based on dilution of riser mud requires economically separating the riser mud into a low density dilution fluid and a higher density drilling fluid. This study investigated the practicality of accomplishing this separation using hydrocyclones and centrifuges and examined the possible benefits and efficiency of each. The separation experiments were conducted using a laboratory centrifuge and 2 inch hydrocyclones. The laboratory centrifuge was able to separate the riser mud into near ideal densities for dilution and drilling fluid. However, the dense slurry retained in the centrifuge had lower emulsion stability than the feed stream. The hydrocyclones achieved much less contrast in density between the low and high density discharges, but consistently resulted in a beneficial increase in the stability of the mud emulsion in all of the flow streams and had more desirable rheological properties. A qualitative comparison indicates that the hydrocyclone separation system may offer a feasible and desirable alternative to centrifuge separation system.

scholarly journals Enhancing the Stability of Invert Emulsion Drilling Fluid for Drilling in High-Pressure High-Temperature Conditions

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2393 ◽  
Author(s):  
Salaheldin Elkatatny
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Rheological Properties ◽  
Drilling Fluid ◽  
Electrical Stability ◽  
Dynamic Conditions ◽  
High Pressure High Temperature ◽  
Invert Emulsion ◽  
The Stability ◽  
Filtration Properties

Drilling in high-pressure high-temperature (HPHT) conditions is a challenging task. The drilling fluid should be designed to provide high density and stable rheological properties. Barite is the most common weighting material used to adjust the required fluid density. Barite settling, or sag, is a common issue in drilling HPHT wells. Barite sagging may cause many problems such as density variations, well-control problems, stuck pipe, downhole drilling fluid losses, or induced wellbore instability. This study assesses the effect of using a new copolymer (based on styrene and acrylic monomers) on the rheological properties and the stability of an invert emulsion drilling fluid, which can be used to drill HPHT wells. The main goal is to prevent the barite sagging issue, which is common in drilling HPHT wells. A sag test was performed under static (vertical and 45° incline) and dynamic conditions in order to evaluate the copolymer’s ability to enhance the suspension properties of the drilling fluid. In addition, the effect of this copolymer on the filtration properties was performed. The obtained results showed that adding the new copolymer with 1 lb/bbl concentration has no effect on the density and electrical stability. The sag issue was eliminated by adding 1 lb/bbl of the copolymer to the invert emulsion drilling fluid at a temperature >300 °F under static and dynamic conditions. Adding the copolymer enhanced the storage modulus by 290% and the gel strength by 50%, which demonstrated the power of the new copolymer to prevent the settling of the barite particles at a higher temperature. The 1 lb/bbl copolymer’s concentration reduced the filter cake thickness by 40% at 400 °F, which indicates the prevention of barite settling at high temperature.

Synthesis of a Novel Ester-Based Drilling Fluid Applicable to High Temperature Conditions

2009 ◽  
Vol 131 (1) ◽  
Author(s):  
M. Nasiri ◽  
S. N. Ashrafizadeh ◽  
A. Ghalambor
Keyword(s):  
High Temperature ◽  
Drilling Fluid ◽  
Temperature Stability ◽  
Ester Hydrolysis ◽  
Favorable Effect ◽  
Drilling Fluids ◽  
Electrical Stability ◽  
Temperature Conditions ◽  
The Stability ◽  
Effect Of Hot Rolling

Ester-based drilling fluids based on aliphatic esters were introduced in 1990. Esters can be synthesized from fatty acids and alcohols. Previous studies indicated that ester hydrolysis in drilling fluids happens only under certain conditions. In order for ester hydrolysis to occur, two primary conditions must be present: high temperature and excessive hydroxyl. When the temperature exceeds 300°F, ester hydrolysis can occur under the presence of excessive hydroxyl. Hydrolysis breaks down the ester component into its parent carboxylic acid and alcohol. The current study shows that the stability of ester-based drilling fluids at high temperature conditions depends on the composition so that the selection of proper components and additives such as emulsifiers, stabilizers, copolymers, viscosifiers, and rheological modifiers can increase the temperature stability of the fluid. Hereby, the application of an ester-based drilling fluid is improved up to 350°F. The composition of the provided fluid is unique in the view point of its higher thermal stability against the previous formulations provided in literature. Furthermore, the experimental results of this study show the favorable effect of hot-rolling pressure on barite sag and electrical stability of the mud, i.e., increasing the pressure at three particular temperatures of 300°F, 325°F, and 350°F reduced the barite sag and at some instances increased the electrical stability.

Reliability of Electrodeposited Copper and Ecrcvd Siof Films for Multilevel Metallization

1999 ◽  
Vol 565 ◽  
Author(s):  
Seoghyeong Lee ◽  
Yong-An Kim ◽  
Kyoung-Woo Lee ◽  
Seil Sohn ◽  
Young-Il Kim ◽  
...  
Keyword(s):  
Plasma Treatment ◽  
Multilayer Structure ◽  
Silicon Oxide ◽  
Electron Cyclotron Resonance ◽  
Chemical Vapor ◽  
Vacuum Furnace ◽  
Electrical Stability ◽  
Metal Interconnects ◽  
The Stability ◽  
Interconnect System

AbstractThe effect of a post plasma treatment on the dielectric properties and reliability of fluorine doped silicon oxide (SiOF) films deposited by electron cyclotron resonance chemical vapor deposition (ECRCVD) was studied. Also, the thermal stability of an electrodeposited Cu / sputtered Ta interconnect system with SiOF intermetal dielectrics was examined by annealing in a vacuum furnace. The stability of the dielectric constant of SiOF films was improved by O2 post plasma treatment. Surface modification by the plasma treatment was effective in prevention of water absorption. The Cu/Ta/SiOF/Si system was thermally stable at least up to 500°C for 3h. For the Cu/Ta/SiOF/Si multilayer structure, the plasma treatment seemed to play a big role in suppressing the interdiffusion between SiOF and metal interconnects. By C-V measurement, the electrical stability of the Cu/Ta/SiOF/Si multilayer structure was found to be stable up to 500°C for 2 h.

Nanoemulsion with Controlled Rheology under Different Temperature for Effective Removal of Oil-based Drilling Fluid in Offshore Drilling

2021 ◽  
Author(s):  
Renzhou Meng ◽  
Chengwen Wang ◽  
Xiliang Dong ◽  
Chao Xiong
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Rheological Properties ◽  
Drilling Fluid ◽  
Offshore Drilling ◽  
Emulsion Droplets ◽  
Effective Removal ◽  
Engineering Requirement ◽  
Important Means ◽  
The Stability

Abstract Oil-based drilling fluid (OBDF) is an important means for offshore drilling, but it would affect the cementing quality. Nanoemulsions shows potential for OBDF removal, but how to prepare nanoemulsion meeting the engineering requirement is lack of good understanding. Moreover, nanoemulsions usually behave badly under low/high temperature, which would restrict the application. Revealing removal mechanisms of nanoemulsion and improving nanoemulsion stability at different temperature are of great significance. The nanoemulsion could rapidly spread on the wellbore surfaces, cause the adhering OBDF to curl into little droplets, and solubilize the removed OBDF. The removal efficiency can reach more than 98%. Low temperature and higher concentration of dispersed phase both increased the viscosity of nanoemulsions stabilized by surfactants. PEGs can induce the bridging of emulsion droplets at low temperature, leading to significant increase of nanoemulsions viscoelasticity at low temperature (around 5°C). To control the rheological properties of nanoemulsions, a hydrophobic association polymer, HAAP, was proposed. Nanoemulsions containing HAAP does not gel at low temperature (< 15°C). And the viscoelasticity of nanoemulsions increased slightly when the temperature is higher than 70°C because of the thermoassociating behavior of polymer, which can ensure the stability of the nanoemulsions at high temperature. This paper is helpful to establish a generic route for preparing nanoemulsions with controlled rheological properties under different temperature, which is benefit for their applications in offshore.

Study on the stability and green application exploration of waste drilling fluid

2019 ◽  
Vol 38 (6) ◽  
pp. 13231
Author(s):  
Bo Liu ◽  
Zhanqiang Wang ◽  
Yingyue Zhu ◽  
Qing Zhong ◽  
Xia Feng ◽  
...  
Keyword(s):  
Drilling Fluid ◽  
The Stability

scholarly journals Experimental Investigation of Water Based Colloidal Gas Aphron Fluid Stability

2019 ◽  
Vol 3 (1) ◽  
pp. 31 ◽  
Author(s):  
Seyed Hosseini-Kaldozakh ◽  
Ehsan Khamehchi ◽  
Bahram Dabir ◽  
Ali Alizadeh ◽  
Zohreh Mansoori
Keyword(s):  
Xanthan Gum ◽  
Drilling Fluid ◽  
Sodium Dodecyl ◽  
Ammonium Bromide ◽  
Drilling Fluids ◽  
Size Distributions ◽  
Electrolyte System ◽  
Colloidal Gas Aphron ◽  
The Stability ◽  
Filtration Properties

Today, the drilling operators use the Colloidal Gas Aphron (CGA) fluids as a part of drilling fluids in their operations to reduce formation damages in low-pressure, mature or depleted reservoirs. In this paper, a Taguchi design of experiment (DOE) has been designed to analyse the effect of salinity, polymer and surfactant types and concentration on the stability of CGA fluids. Poly Anionic Cellulose (PacR) and Xanthan Gum (XG) polymers are employed as viscosifier; Hexadecyl Trimethyl Ammonium Bromide (HTAB) and Sodium Dodecyl Benzene Sulphonate (SDBS) have been also utilized as aphronizer. Moreover, bubble size distributions, rheological and filtration properties of aphronized fluids are investigated. According to the results, the polymer type has the highest effect, whereas the surfactant type has the lowest effect on the stability of CGA drilling fluid. It was also observed that increasing salinity in CGA fluid reduces the stability. Finally, it should be noted that the micro-bubbles generated with HTAB surfactant in an electrolyte system, are more stable than SDBS surfactant.

scholarly journals RADIX: a minimal-resources rapid-access drilling system

2014 ◽  
Vol 55 (68) ◽  
pp. 34-38 ◽  
Author(s):  
J. Schwander ◽  
S. Marending ◽  
T.F. Stocker ◽  
H. Fischer
Keyword(s):  
Drilling Fluid ◽  
Ice Core ◽  
Ice Sheet ◽  
Minimum Size ◽  
Rapid Access ◽  
Drilling System ◽  
Low Costs ◽  
Drilling Site ◽  
Remote Sensing Methods

AbstractDetermining the expected age at a potential ice-core drilling site on a polar ice sheet generally depends on a combination of information from remote-sensing methods, estimates of current accumulation and modelling. This poses irreducible uncertainties in retrieving an undisturbed ice core of the desired age. Although recently perfected radar techniques will improve the picture of the ice sheet below future drilling sites, rapid prospective drillings could further increase the success of deep drilling projects. Here we design and explore a drilling system for a minimum-size rapid-access hole. The advantages of a small hole are the low demand for drilling fluid, low overall weight of the equipment, fast installing and de-installing and low costs. We show that, in theory, drilling of a 20 mm hole to a depth of 3000 m is possible in ∼4 days. First concepts have been realized and verified in the field. Both the drill cuttings and the hole itself can be used to characterize the properties of the ice sheet and its potential to provide a trustworthy palaeo-record. A candidate drilling site could be explored in ∼2 weeks, which would enable the characterization of several sites in one summer season.

scholarly journals Study on the stability of a shear-thinning suspension used in oil well drilling

2018 ◽  
Vol 73 ◽  
pp. 10 ◽  
Author(s):  
Flávia M. Fagundes ◽  
Nara B.C. Santos ◽  
João Jorge R. Damasceno ◽  
Fábio O. Arouca
Keyword(s):  
Gamma Ray ◽  
Drilling Fluid ◽  
Shear Thinning ◽  
Drilling Fluids ◽  
Oil Well ◽  
Drilling Process ◽  
Well Drilling ◽  
Constant Rate ◽  
The Stability ◽  
Solid Liquid

In order to avoid solid-liquid gravitational separation of particles in the drilling fluid and cuttings generated in this process, the oil industry has been developing drilling fluids with shear-thinning and thixotropic characteristics. In case of operational stops in the drilling process, the intense sedimentation of these particles can damage the equipment used and the well. In this context, this study simulated an operational stop to obtain information about stability of solids in a paraffin-based suspension with time-dependent shear-thinning behavior, which has already been used in current drilling processes. A long-term test using gamma-ray attenuation technique identified the separation dynamics of a set of micrometric particles belonging to and incorporated into the drilling fluid during operation. This test verified the typical regions of gravitational sedimentation and, through constant concentration curves, indicated that the sedimentation process did not occur at a constant rate. This study also proposed a constitutive equation for pressure on solids.

Stability Performance of an Energy Filtering TEM

2000 ◽  
Vol 6 (S2) ◽  
pp. 214-215
Author(s):  
G. Benner ◽  
E. Zellmann ◽  
A. Harscher ◽  
R. Härle ◽  
B. Kabius ◽  
...  
Keyword(s):  
Energy Resolution ◽  
Optical Design ◽  
Electrical Stability ◽  
Combined System ◽  
Long Term Stability ◽  
Energy Filtering ◽  
Stability Performance ◽  
Electron Microscopes ◽  
Focus Variation ◽  
The Stability

The electron-optical design and the technical realisation of correctors, monochromators and imaging spectrometers as well as methods of resolution improvement (Focus variation, Holography) have made significant progress in the past few years. For all such devices and methods the mechanical and electrical stability of the microscope are the main challenges.Such requirements are even more critical in case of Energy Filtering Transmission Electron Microscopes (EFTEMs), where the achievement of highly resolved analytical results requires long detection times (in the range of a few 10s of seconds). Resolution in such case could mean both spatial and energy resolution even at the same time. The stability performance of the combined system is more complex than the sum of the stabilities of the single components. Thus, a specified HT short- and long-term stability of 2 ppm is not sufficient to achieve an energy resolution of 0.2 eV at 100 kV acceleration voltage.

Sign in / Sign up

Export Citation Format

Share Document