Optimal Parameters and Characteristics of a Three Degree of Freedom Dynamic Vibration Absorber

2012 ◽  
Vol 134 (2) ◽  
Author(s):  
Mariano Febbo
Keyword(s):  
Simulated Annealing ◽  
Vibration Reduction ◽  
Observation Point ◽  
Degree Of Freedom ◽  
Vibration Absorber ◽  
Optimal Parameters ◽  
Dynamic Vibration Absorber ◽  
Rotational Mode ◽  
Dynamic Vibration ◽  
Three Degree Of Freedom

The present study is devoted to the determination of the optimal parameters and characteristics of a three degree of freedom dynamic vibration absorber (3 DOF DVA) for the vibration reduction of a plate at a given point. The optimization scheme uses simulated annealing and constrained simulated annealing, which is capable of optimizing systems with a set of constraints. Comparisons between a 3 DOF DVA and multiple (5) 1 DOF DVAs show a better performance of the former for vibration reduction. Regarding the characteristics of the optimal 3 DOF DVA, numerical tests reveal that the absorber is robust under variations of the observation point and for 10% variations of its mass, stiffness and damping. From the analysis of parameter changes of the plate, it is found that the optimal 3 DOF DVA is almost insensitive to a mass change, and sensitive to a change of Young’s modulus for low frequencies. In this case, a decrease in Young’s modulus causes a decrease in its effectiveness, and an increase improves it. The study of the effect of the 3 DOF DVA location on its effectiveness reveals that the requirements of closeness of the absorber to an antinode of the bare primary structure and to the observation point improve its performance. Additionally, for a rotational mode of the 3-DOF DVA about some axis, the effectiveness of the absorber at a given frequency can be notably increased if it is located at a position of the primary system with an in-phase or out-of- phase motion of the attachment points according to the rotational-mode characteristics of the 3-DOF DVA at this frequency.

scholarly journals Pendekatan Eksperimen Karakteristik Respon Getaran Sistem Two Degree of Freedom dengan Penambahan Independent Dual Dynamic Vibration Absorber

2019 ◽  
Vol 3 (2) ◽  
pp. 85
Author(s):  
Susastro Susastro ◽  
Novi Indah Riani
Keyword(s):  
Vibration Reduction ◽  
Degree Of Freedom ◽  
The Other ◽  
Vibration Absorber ◽  
Dynamic Vibration Absorber ◽  
Maximum Reduction ◽  
Dynamic Vibration ◽  
Translational Vibration ◽  
Mathematical Equations ◽  
Two Degree Of Freedom

Vibration is one of the problems that must be reduced in a vehicle. There are many ways to reduce vibration in vehicles, one of them is by adding Dynamic vibration absorber (DVA). While Dual Dynamic vibration absorber (dDVA) is a DVA period that is able to move in the translational direction given to the system to reduce translation vibration and when there is resonance. Translation DVA is an additional type of time used to reduce the vibration of the translation direction. So far there is not much research related to the use of translational DVA to reduce rotational vibrations as well as translation. In this study, a study was conducted related to the use of independent double translational DVA (dDVA) to reduce translation vibrations as well as rotation of the beam. The research was conducted by modeling the system obtained into mathematical equations and simulations were carried out to determine the characteristics of vibrations that arise. In the simulation, one of the DVA periods is placed at the center of the main system period, while the other DVA period is given a change between the center period and the end of the system. The results of the study show that the maximum reduction in translational vibration is 95.51% and occurs when the absorber is placed at the center of the system, while the maximum rotation vibration reduction is 56.62% and is obtained when the system is given with an arm ratio of 1 and zero.

scholarly journals Study on the Vibration Suppression Method of Urban Railway Vehicles Based on a Composite Dynamic Vibration Absorber

2019 ◽  
Vol 296 ◽  
pp. 01010
Author(s):  
Qian Sun ◽  
Yongpeng Wen ◽  
Yu Zou
Keyword(s):  
Vibration Suppression ◽  
Vibration Reduction ◽  
Low Frequency ◽  
Peak Frequency ◽  
Degree Of Freedom ◽  
Vibration Absorber ◽  
Dynamic Vibration Absorber ◽  
Single Degree Of Freedom ◽  
Single Degree ◽  
Dynamic Vibration

To reduce the bounce and the pitch vibration of carbody, a vertical dynamic model for urban rail vehicles is established to analyze the vibration response of the carbody in the low frequency range. In this paper, different methods of single-degree-of-freedom dynamic vibration absorber to suppress the vibration for carbody are investigated. The limits of single-degree-of-freedom dynamic vibration absorber to the vibration reduction effect of carbody are pointed out. After that, the design of a composite dynamic vibration absorber including a double oscillator structure is introduced. A vibration discreteness index is used to evaluate dynamic vibration absorbers with various designs for the vibration damping performance. Finally, the vibration reduction performance of the composite dynamic vibration absorber is verified by Sperling’s riding index. The results demonstrate that the performance of the single degree of freedom dynamic vibration absorber attached to a carbody may increase the vibration within a partial scope, when the peak frequency of vibration is far away from the design frequency. The installation of the composite dynamic vibration absorber vibration provides gentler running experience for passengers.

scholarly journals Study on Multi-Degree of Freedom Dynamic Vibration Absorber of the Carbody of High-Speed Trains

2021 ◽  
Author(s):  
Yu SUN ◽  
Jinsong Zhou ◽  
Dao Gong ◽  
Yuanjin Ji
Keyword(s):  
Vibration Control ◽  
High Speed ◽  
Degrees Of Freedom ◽  
Dynamic Stiffness ◽  
Degree Of Freedom ◽  
Vibration Absorber ◽  
High Speed Train ◽  
Dynamic Vibration Absorber ◽  
Multiple Degrees Of Freedom ◽  
Dynamic Vibration

Abstract To absorb the vibration of the carbody of the high-speed train in multiple degrees of freedom, a multi-degree of freedom dynamic vibration absorber (MDOF DVA) is proposed. Installed under the carbody, the natural vibration frequency of the MDOF DVA from each DOF can be designed as a DVA for each single degree of freedom of the carbody. Hence, a 12-DOF model including the main vibration system and a MDOF DVA is established, and the principle of Multi-DOF dynamic vibration absorption is analyzed by combining the design method of single DVA and genetic algorithm. Based on a high-speed train dynamics model including an under-carbody MDOF DVA, the vibration control effect on each DOF of the MDOF DVA is analyzed by the virtual excitation method. Moreover, a high static and low dynamic stiffness (HSLDS) mount is proposed based on a cam–roller–spring mechanism for the installation of the MDOF DVA due to the requirement of the low vertical dynamic stiffness. From the dynamic simulation of a non-linear model in time-domain, the vibration control performance of the MDOF DVA installed with nonlinear HSLDS mount on the carbody is analyzed. The results show that the MDOF DVA can absorb the vibration of the carbody in multiple degrees of freedom effectively, and improve the running ride quality of the vehicle.

scholarly journals Application of Adaptive Tuned Magneto-Rheological Elastomer for Vibration Reduction of a Plate by a Variable-Unbalance Excitation

2020 ◽  
Vol 10 (11) ◽  
pp. 3934 ◽  
Author(s):  
Un-Chang Jeong
Keyword(s):  
Vibration Reduction ◽  
Excitation Frequency ◽  
Target Object ◽  
Vibration Absorber ◽  
Magnetorheological Elastomer ◽  
Dynamic Vibration Absorber ◽  
Mass Part ◽  
Dynamic Vibration ◽  
Frequency Excitation ◽  
Magneto Rheological

The present study on vibration reduction in systems wherein the excitation frequency is variable designed and fabricated a magnetorheological elastomer (MRE)-based tunable dynamic vibration absorber and evaluated its performance in an experimental manner. The design of an MRE-based adaptive tuned dynamic vibration absorber (ATDVA) involves designing two parts: stiffness and mass. Before designing the MRE-based ATDVA, this study determined the resonance frequency of a target object for vibration reduction. For the design of the ATDVA’s stiffness part, the thickness of specimens was determined by measuring the rate of variation of the MRE’s shear modulus with respect to the MRE’s thickness. The design of the mass part was optimized using sensitivity analysis and genetic algorithms after the derivation of formulas for its magnetic field and mass. Further, upon the application of an electric current to the MRE, its stiffness was measured so that the stiffness of the designed MRE-based ATDVA could be tuned accordingly. Finally, the vibration-reducing performance of the MRE-based ATDVA was evaluated to determine the applicability of the vibration absorber under the condition of variable-frequency excitation.

Sign in / Sign up

Export Citation Format

Share Document