Fluidelastic Instability in Normal and Parallel Triangular Arrays of Finned Tubes

2012 ◽  
Vol 134 (2) ◽  
Author(s):  
J. Wang ◽  
D. S. Weaver
Keyword(s):  
Finned Tube ◽  
Effective Diameter ◽  
Process Industries ◽  
Finned Tubes ◽  
Triangular Arrays ◽  
Tube Bundles ◽  
Fluidelastic Instability ◽  
The Difference ◽  
The Stability ◽  
Bare Tube

An experimental study was carried out to investigate fluidelastic instability in finned tube bundles in normal and parallel triangular arrays. Three arrays of each geometry type were studied experimentally: two arrays with serrated, helically wound finned tubes of different fin densities, and a bare tube array with the same base diameter as the finned tubes. All six tube arrays studied had the same tube pitch. The finned tubes under consideration were commercial finned tubes typically used in the fossil and process industries. For the purpose of the present investigation, the concept of “effective diameter” of a finned tube, as previously used to predict vortex shedding, was used to compare the finned tube results with other finned tube results as well as the existing bare tube world data. The experimental results for the triangular arrays show that the fin’s structure strongly influences the fluidelastic stability of finned tube bundles and the fin pitch is demonstrated to reduce the difference in the stability threshold between the tube array geometries as the fin density increases. Overall, the effect of serrated fins on fluidelastic instability is very complex and array geometry dependent, stabilizing some arrays and destabilizing others. Clearly, the effect of fins cannot be accounted for by the simple use of an effective diameter of an equivalent bare tube. An earlier version of this paper appeared at the ASME 2010 FSI Conference, FEDSM-ICNMM2010-30223.

Fluidelastic Instability in Normal and Parallel Triangular Arrays of Finned Tubes

2010 ◽  
Author(s):  
J. Wang ◽  
D. S. Weaver
Keyword(s):  
Finned Tube ◽  
Effective Diameter ◽  
Process Industries ◽  
Finned Tubes ◽  
Triangular Arrays ◽  
Tube Bundles ◽  
Fluidelastic Instability ◽  
The Difference ◽  
The Stability ◽  
Bare Tube

An experimental study was carried out to investigate fluidelastic instability in finned tube bundles in normal and parallel triangular arrays. Three arrays of each geometry type were studied experimentally: two arrays with serrated, helically wound finned tubes of different fin densities, and a bare tube array with the same base diameter as the finned tubes. All six tube arrays studied had the same tube pitch. The finned tubes under consideration were commercial finned tubes typically used in the fossil and process industries. For the purpose of the present investigation, the concept of “effective diameter” of a finned tube, as previously used to predict vortex shedding, was used to compare the finned tube results with other finned tube results as well as the existing bare tube world data. The experimental results for the triangular arrays show that the fin’s structure strongly influences the fluidelastic stability of finned tube bundles and the fin pitch is demonstrated to reduce the difference in the stability threshold between the tube array geometries as the fin density increases. Overall, the effect of serrated fins on fluidelastic instability is very complex and array geometry dependent, stabilizing some arrays and destabilizing others. Clearly, the effect of fins cannot be accounted for by the simple use of an effective diameter of an equivalent bare tube.

scholarly journals The Effect of Fins on Fluidelastic Instability in In-Line and Rotated Square Tube Arrays

2010 ◽  
Vol 132 (5) ◽  
Author(s):  
Robert H. Lumsden ◽  
David S. Weaver
Keyword(s):  
Finned Tube ◽  
Experimental Program ◽  
Effective Diameter ◽  
Process Industries ◽  
Finned Tubes ◽  
Tube Arrays ◽  
Fluidelastic Instability ◽  
The Stability ◽  
Tube Pitch ◽  
Bare Tube

An experimental program was conducted to examine fluidelastic instability in in-line and rotated square finned tube arrays. Three arrays of each geometry type were studied: two with serrated, helically wound finned tubes of different fin densities and the third is a bare tube, which had the same base diameter as the finned tubes. The finned tubes under consideration were commercial finned tubes of a type typically used in the fossil and process industries. The addition of fins to tubes in heat exchangers enhances heat transfer due to the increased surface area and the turbulence produced by the flow moving over the fins. The resulting flow pattern/distribution due to the fins is, therefore, more complex than in bare tube arrays. Previous research has shown that an effective diameter of a finned tube is useful in the prediction of vortex shedding. This concept is used to compare the finned tube results with the existing bare tube array guidelines for fluidelastic instability. All of the tube arrays in the present study have the same tube pitch and have been scaled to have the same mass ratio. The results for rotated square arrays suggest that the use of an effective diameter is beneficial in the scaling of fluidelastic instability and the finned tube results are found to fit within the scatter of the existing data for fluidelastic instability. For in-line square arrays, the results indicate that fins significantly increase the stability threshold. An earlier version of this paper appeared at the ASME 2007 PVP Division Conference, PVP2007-26597.

The Effect of Fins on Fluidelastic Instability in In-Line and Rotated Square Arrays

2007 ◽  
Author(s):  
Robert H. Lumsden ◽  
David S. Weaver
Keyword(s):  
Heat Exchangers ◽  
Cross Flow ◽  
Finned Tube ◽  
Experimental Program ◽  
Effective Diameter ◽  
Finned Tubes ◽  
Increased Risk ◽  
Tube Arrays ◽  
Fluidelastic Instability ◽  
Bare Tube

The study of fluidelastic instability in tube arrays has been ongoing for four decades. Although much research has been conducted, a full understanding of the mechanisms involved is still not available. Designers of cross-flow heat exchangers must depend on experience and empirical data from laboratory studies. As new designs are developed, which differ from these experimental facilities, there is an increased risk of failure due to fluidelastic instability. An experimental program was conducted to examine fluidelastic instability in in-line and rotated square finned tube arrays. Three arrays of each geometry type were studied; two with serrated, helically wound finned tubes of different fin densities, and the third, a bare tube which had the same base diameter as the finned tubes. The finned tubes under consideration were commercial finned tubes of a type typically used in the fossil and process industries. The addition of fins to tubes in heat exchangers enhances heat transfer due to the increased surface area and the turbulence produced by the flow moving over the fins. The resulting flow pattern/distribution due to the fins is therefore much more complicated than in bare tube arrays. Previous research has shown that an effective diameter of a finned tube is useful in the prediction of vortex shedding. This concept is used to compare the finned tube results with the existing bare tube array guidelines for fluidelastic instability. All of the tube arrays in the present study have the same tube pitch, and have been scaled to have the same mass ratio. Results for the rotated square arrays show that the use of an effective diameter is beneficial in the scaling of fluidelastic instability and the finned tube results are found to fit within the scatter of the existing data for fluidelastic instability. For in-line square arrays, the results indicate that fins significantly increase the stability threshold.

Flow-Induced Vibration in Spiral Finned Gas Tube Bundle Heat Exchangers

2003 ◽  
Author(s):  
Michael Fischer
Keyword(s):  
Heat Exchangers ◽  
Tube Bundle ◽  
Practical Importance ◽  
Acoustic Resonance ◽  
Finned Tube ◽  
Flow Induced Vibration ◽  
Finned Tubes ◽  
The Past ◽  
Short Period ◽  
Fluidelastic Instability

In the past finned tube bundle heat exchangers were often subject of severe damages due to flow-induced vibration followed by high amounts of loss for the operator. A case of practical importance is the design of spiral finned gas tube bundle heat exchangers that still have been investigated in literature only seldom. Both acoustic resonance and fluidelastic instability can lead to tube rupture within a short period of operation. In this paper analytic calculation methods for tube Eigenfrequencies are extended to spiral finned tubes. The results are in agreement with static and vibrational experiments. Stability criteria for fluidelastic instability are derived by flow channel experiments extending Connor’s equation to the design of spiral finned tube bundles. A number of cases of damage is described. The importance of correct damping values is demonstrated. The scheme reported in this paper is able to avoid damages in spiral finned tube bundle heat exchangers due to fluidelastic instability.

Use of a Lyophilized Reference Plasma to Compare Coagulation Test Procedures

1975 ◽  
Vol 34 (02) ◽  
pp. 426-444 ◽  
Author(s):  
J Kahan ◽  
I Nohén
Keyword(s):  
Oral Anticoagulant Therapy ◽  
Repeated Measurements ◽  
Test Procedures ◽  
Coagulation Activity ◽  
Close Relationship ◽  
Measured Activity ◽  
Test Materials ◽  
The Difference ◽  
The Stability ◽  
The One

SummaryIn 4 collaborative trials, involving a varying number of hospital laboratories in the Stockholm area, the coagulation activity of different test materials was estimated with the one-stage prothrombin tests routinely used in the laboratories, viz. Normotest, Simplastin-A and Thrombotest. The test materials included different batches of a lyophilized reference plasma, deep-frozen specimens of diluted and undiluted normal plasmas, and fresh and deep-frozen specimens from patients on long-term oral anticoagulant therapy.Although a close relationship was found between different methods, Simplastin-A gave consistently lower values than Normotest, the difference being proportional to the estimated activity. The discrepancy was of about the same magnitude on all the test materials, and was probably due to a divergence between the manufacturers’ procedures used to set “normal percentage activity”, as well as to a varying ratio of measured activity to plasma concentration. The extent of discrepancy may vary with the batch-to-batch variation of thromboplastin reagents.The close agreement between results obtained on different test materials suggests that the investigated reference plasma could be used to calibrate the examined thromboplastin reagents, and to compare the degree of hypocoagulability estimated by the examined PIVKA-insensitive thromboplastin reagents.The assigned coagulation activity of different batches of the reference plasma agreed closely with experimentally obtained values. The stability of supplied batches was satisfactory as judged from the reproducibility of repeated measurements. The variability of test procedures was approximately the same on different test materials.

HEAT AND MASS TRANSFER AND RESISTANCE CHARACTERISTICS OF EVAPORATIVE AIR COOLER WITH HIGH FINNED-TUBE BUNDLES

2018 ◽  
Vol 49 (17) ◽  
pp. 1705-1720 ◽  
Author(s):  
Qing Zhang ◽  
Xuesheng Wang ◽  
Weicheng Ruan ◽  
Qinzhu Chen ◽  
Zilong Liu
Keyword(s):  
Mass Transfer ◽  
Heat And Mass Transfer ◽  
Finned Tube ◽  
Tube Bundles ◽  
Air Cooler

In the stability of paints and varnishes for protective and decorative wood finish

2016 ◽  
Author(s):  
Ю.И. Цой
Keyword(s):  
Organic Solvents ◽  
Evaluation Criteria ◽  
Ternary Systems ◽  
Solubility Parameters ◽  
Formaldehyde Resin ◽  
Film Forming ◽  
The Difference ◽  
Molecular Forces ◽  
The Stability ◽  
Thermodynamic Interaction

Задача получения однородного состава ЛКМ сводится к правильному выбору пленкообразователей и соответствующих растворителей и, в случае необходимости, разбавителей и добавок. На основе положений теории растворимости была проведена оценка совместимости компонентов и стабильности таких систем. Критериями оценки были приняты параметры растворимости и термодинамического взаимодействия. Исследовали совместимость алкидных лаков с аминоформальдегидными смолами в бутаноле, и результаты этих исследований представлены в треугольной фазовой диаграмме. Для оценки совместимости смол по результатам расчета параметров термодинамического взаимодействия были построены спинодали для тройных систем. Как показывает анализ результатов проведенных исследований, даже при большой разности ?? = |?12 – ?13| = 0,2 наблюдается небольшая область несовместимости. С уменьшением разности ?? область несовместимости сужается. При ?23 > ?с область несовместимости расширяется как для ? = 0,2, так и для ?? = 0,1 и ?? = 0. Таким образом, для таких систем на совместимость компонентов, в первую очередь, влияет их взаимодействие между собой – чем оно больше, тем лучше они совместимы. Проведенные исследования показали, что парциальные параметры растворимости, учитывающие природу когезионных сил, более объективно характеризуют растворимость пленкообразующих смол в органических растворителях, чем их общий параметр растворимости. Растворимость пленкообразующих алкидных и этерифицированных аминоформальдегидных смол в органических растворителях обусловлена термодинамическим взаимодействием молекулярных сил различной природы. Стабильность смеси алкидной и этерифицированной аминоформальдегидной смолы в бутаноле обусловлена в большей степени термодинамическим взаимодействием молекулярных сил; при этом степень бутанолизации меламиноформальдегидной смолы оказывает наибольшее влияние на стабильность cистемы. Проведенные исследования по стабильности лакокрасочных смесей из различных пленкообразующих смол на основе рассмотренных критериев оценки могут быть использованы для совершенствования технологии защитно-декоративной отделки древесины. The problem of obtaining a homogeneous composition of the coatings is reduced to the proper selection of film-forming agents, and diluent and, if appropriate, diluents and additives. On the basis of the theory of solubility, we have carried out the assessment of the compatibility of the components and stability of such systems. The evaluation criteria were adopted the parameters of the solubility and thermodynamic interaction. Researched the compatibility with alkyd varnishes aminoformaldehyde resin in butanol, and the results of these studies are presented in the triangular phase diagram. To evaluate the compatibility of the resins according to the results of calculation of thermodynamic parameters of interaction were built spinodal for ternary systems. As the analysis of the results of the studies, even when the difference ??|?12 – ?13| = 0,2 there is a small area of incompatibility. With the decrease of the difference ? ? region incompatibility narrows. When ?23> ?с region incompatibility extends to ?? = 0,2, and for ?? = 0.1 and ?? = 0. Thus, for such systems, compatibility of components, primarily, affects their interaction with each other – the further away it is, the better they are compatible. Studies have shown that the partial solubility parameters, which take into account the nature of cohesive forces, more objectively characterize the solubility of film-forming resins in organic solvents than their total solubility parameter. The solubility and film-forming aminoformaldehyde esterified alkyd resins in organic solvents due to thermodynamic interaction of molecular forces of different nature. Тhe stability of the mixture and aminoformaldehyde esterified alkyd resin in butanol is generated largely by thermodynamic forces of molecular interaction; the degree of butanolate melamine-formaldehyde resin has the greatest effect on the stability of the system. Conducted research on the stability of the paint mixtures of various film-forming resins on the basis of the evaluation criteria can be used to improve the technology of protective and decorative wood finish.

Stability and mutual impact of perception of parental pressure and infants' social support – A study based on the difference between employment status and household income

2021 ◽  
pp. 002072092199705
Author(s):  
Yong Wang
Keyword(s):  
Household Income ◽  
Employment Status ◽  
Working Mothers ◽  
Social Research ◽  
Research Report ◽  
Parental Pressure ◽  
Income Levels ◽  
Significant Difference ◽  
The Difference ◽  
The Stability

The purpose of this study is to explore the stability and interaction between parental pressure and social research report, as well as the role of employment status and family income levels in this process. This study used a special study on Korean children (PSKC) 2–4 waves. Use t-test, correlation and autoregressive cross-delay modeling to analyze the data. The main findings of this study are: First, over time, parental pressure and mother’s social research report are consistent. Secondly, the pressure of motherhood and childcare has an obvious lagging effect on upbringing, and vice versa. Third, there is no significant difference between working mothers and non-working mothers in terms of the stability of working parents' pressure, social research report and social research report for children's pressure channels. However, parental pressure can only predict the social research report of working mothers. Fourth, there is no significant difference between the stability and interaction of these two structures in household income levels. In short, the results show that, over time, parental pressure is consistent with mother’s social research report. The results also show that there is a significant cross-lag effect between the mothers’ perceptions of mutual pressure analysis. In the process from parental pressure to social research report, I found the difference between working and non-working mothers. The advantage of this study is that the expected longitudinal design was adopted during infancy and the priority between the two structures can be considered. The results of this study can be used as a source of intervention plans to help parents withstand severe parenting pressure and lack of social research report.

Sign in / Sign up

Export Citation Format

Share Document