Fatigue Assessment of Welded Joints Taking Into Account Effects of Residual Stress

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
Nur Syahroni ◽  
Stig Berge
Keyword(s):  
Residual Stress ◽  
Fatigue Strength ◽  
Welded Joints ◽  
Fatigue Testing ◽  
International Association ◽  
Hot Spot ◽  
Strain Gauges ◽  
Mean Stress ◽  
Element Analysis ◽  
Fatigue Design

Residual stress may have a significant effect on the fatigue strength of welded joints. As a nonfluctuating stress, it has an effect similar to that of the mean stress. Recently the International Association of Ship Classification Societies (IACS) has issued Common Structural Rules (CSR) for respectively tankers and bulk carriers. The effect of mean stress in fatigue design is taken into account in both sets of rules. However, the treatment is quite different, in particular with regard to residual stress and shakedown effects. In the present paper a comparative study of fatigue design procedures of the IACS rules is reported, with emphasis on residual stress effects. Testing was carried out with longitudinal attachment welds in the as-welded condition. The initial residual stress was measured by a sectioning method using strain gauges. Hot spot stress was determined experimentally by strain gauges and numerically by finite element analysis using different types of elements. Fatigue testing was carried out and SN-curves were plotted according to the relevant stress as specified by the rules. In order to investigate the shakedown effect of residual stress, testing was performed for several preload conditions, which could be taken to represent maximum load levels in a load history. The aim of the study is to contribute towards a better understanding of the effect of residual stress and shakedown on fatigue strength of welded joints.

Fatigue Assessment of Welded Joints Taking Into Account Effects of Residual Stress

2010 ◽  
Author(s):  
Nur Syahroni ◽  
Stig Berge
Keyword(s):  
Residual Stress ◽  
Fatigue Strength ◽  
Welded Joints ◽  
Fatigue Testing ◽  
International Association ◽  
Hot Spot ◽  
Mean Stress ◽  
Element Analysis ◽  
Structural Rules ◽  
Fatigue Design

Residual stress may have a significant effect on the fatigue strength of welded joints. As a non-fluctuating stress, it has an effect similar to that of the mean stress. Recently the International Association of Ship Classification Societies (IACS) has issued Common Structural Rules (CSR) for respectively tankers (IACS 2006a) and bulk carriers (IACS 2006b). The effect of mean stress in fatigue design is taken into account in both sets of rules. However, the treatment is quite different, in particular with regard to residual stress and shakedown effects. In the present paper a comparative study of fatigue design procedures of the IACS rules is reported, with emphasis on residual stress effects. Testing was carried out with longitudinal attachment welds in the as-welded condition. The initial residual stress was measured by a sectioning method using strain gages. Hot spot stress was determined experimentally by strain gauges and numerically by finite element analysis using different types of elements. Fatigue testing was carried out and SN-curves were plotted according to the relevant stress as specified by the rules. In order to investigate the shake-down effect of residual stress, testing was performed for several pre-load conditions which could be taken to represent maximum load levels in a load history. The aim of the study is to contribute towards better understanding of the effect of residual stress and shakedown on fatigue strength of welded joints.

Residual Stress Shakedown in Typical Weld Joints and Its Effect on Fatigue of FPSOs

2007 ◽  
Author(s):  
Liangbi Li ◽  
Torgeir Moan ◽  
Bin Zhang
Keyword(s):  
Residual Stress ◽  
Cyclic Loading ◽  
Residual Stresses ◽  
Welded Joints ◽  
Hot Spot ◽  
Fatigue Behaviour ◽  
Combined Effect ◽  
Element Analysis ◽  
Variable Amplitude ◽  
Initial Residual Stress

Structural members of FPSO hulls often undergo fairly large static loading before they enter service or variable amplitude cyclic loading when they are in service. The combined effect of both applied stress and high initial residual stress is expected to cause shakedown of the residual stresses. Only a few papers seem to deal with appropriate procedures for fatigue analysis by considering the combined effect of variable amplitude cyclic loading with shakedown of residual stresses. Hence, the fatigue behaviour of welded joints in some experiments could not be explained reasonably well. In this paper, some typical welded connections in ship-shaped structures are investigated with 3-D elastic-plastic finite element analysis. The effect of residual stress relaxation, initial residual stress and the applied load after variable amplitude cyclic loading is revealed, and a formula for predicting the residual stress at hot spot quantitatively is proposed. Based on the formula, an improved fatigue procedure is introduced. The proposed fatigue procedure was validated against the experimental results. Therefore, the modified fatigue procedure could be applied to welded joints under arbitrary cyclic loading while accounting for shakedown of residual stresses.

Fatigue Strength Evaluation of the Load-Carrying Cruciform Fillet Welded Joints Using Hot-Spot Stress

2006 ◽  
Vol 324-325 ◽  
pp. 1281-1284 ◽  
Author(s):  
Byeong Wook Noh ◽  
Jung I. Song ◽  
Sung In Bae
Keyword(s):  
Fatigue Strength ◽  
Welded Joints ◽  
Hot Spot ◽  
Plate Thickness ◽  
Structural Stress ◽  
Leg Length ◽  
Element Analysis ◽  
Hot Spot Stress ◽  
Load Carrying ◽  
Weld Toe

In this study, fatigue strength of load-carrying cruciform fillet welded joints were evaluated using a new method proposed by Yamada, for geometric or structural stress in welded joint, that is, one-millimeter stress below the surface in the direction corresponding to the expected crack path. Validity of the method is verified by analyzing fatigue test results for load-carrying cruciform welded specimens has different size of weld toe radius, leg length and plate thickness reported in literature. Structural stress concentration factor for 1mm below the surface was calculated by finite element analysis for each specimen respectively. When compared to the basic fatigue resistance curve offered by BS7608, the one-millimeter stress method shows conservative evaluation for load-carrying cruciform fillet welded joints.

Residual Stress Release and Its Effects on the Fatigue Strength of Typical Welded Joints in Cone-Cylinder Pressure Structures

2021 ◽  
Vol 111 ◽  
pp. 102673
Author(s):  
Liangbi Li ◽  
Jingxi Zhang ◽  
Yiwen Zhang ◽  
Deqin Zhu ◽  
Zhengquan Wan ◽  
...  
Keyword(s):  
Residual Stress ◽  
Fatigue Strength ◽  
Welded Joints ◽  
Cylinder Pressure ◽  
Stress Release

scholarly journals Use of 3D Scan of Weld Joint in Finite Element Analysis and Stochastic Analysis of Hot-Spot Stresses in Tubular Joint for Fatigue Life Estimation

2019 ◽  
Author(s):  
Mikkel L. Larsen ◽  
Vikas Arora ◽  
Marie Lützen ◽  
Ronnie R. Pedersen ◽  
Eric Putnam
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Welded Joints ◽  
Hot Spot ◽  
Strain Range ◽  
Fe Model ◽  
Design Codes ◽  
Element Analysis ◽  
Hot Spot Stress ◽  
Weld Toe

Abstract Several methods for modelling and finite element analysis of tubular welded joints are described in various design codes. These codes provide specific recommendations for modelling of the welded joints, using simple weld geometries. In this paper, experimental hot-spot strain range results from a full-scale automatically welded K-node test are compared to corresponding finite element models. As part of investigating the automatically welded K-joint, 3D scans of the weld surfaces have been made. These scans are included in the FE models to determine the accuracy of the FE models. The results are compared to an FE model with a simple weld geometry based on common offshore design codes and a model without any modelled weld. The results show that the FE model with 3D scanned welds is more accurate than the two simple FE models. As the weld toe location of the 3D scanned weld is difficult to locate precisely in the FE model and as misplacement of strain gauges are possible, stochastic finite element modelling is performed to analyse the resulting probabilistic hot-spot stresses. The results show large standard deviations, showing the necessity to evaluate the hot-spot stress method when using 3D scanned welds.

Differences in Fatigue Strength Between Arc and Laser Hybrid Welded Joints

2008 ◽  
Vol 24 (03) ◽  
pp. 139-146
Author(s):  
H. Remes ◽  
P. Varsta
Keyword(s):  
Fatigue Strength ◽  
Welded Joints ◽  
Fatigue Tests ◽  
Notch Depth ◽  
Butt Joints ◽  
Fatigue Design ◽  
Notch Stress ◽  
Notch Geometry ◽  
Laser Hybrid ◽  
Fatigue Endurance

This paper presents the results of fatigue tests, including tests of laser hybrid and arc welded butt joints, for two plate thicknesses, 6 and 12 mm. Pure laser welded joints were also tested. The S-N curves based on nominal stresses for the different welded joints are presented. The results were further analyzed using the notch stress approach, where the fatigue notch factors were determined from the measured geometries of the welded joints. Unexpected differences in the S-N curves based on the notch stresses were found between the laser hybrid and arc welded joints and between the laser hybrid and pure laser welded joints. The reasons for this difference were studied with the help of extensive measurements of weld notch geometries. Significant differences in the geometries were observed. Taking into account the notch geometry and the notch depth, the notch stress approach partially explains the differences between the fatigue endurance limits of the laser hybrid and arc welded joints. The applicability of the notch stress approach to the fatigue design of laser hybrid welded joints is also discussed.

Estimation of Residual Stresses in Steel Welded Joints Using Three Dimensional Finite Element Analysis

2018 ◽  
Author(s):  
Shivdayal Patel ◽  
B. P. Patel ◽  
Suhail Ahmad
Keyword(s):  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Residual Stresses ◽  
Boundary Conditions ◽  
Welding Speed ◽  
Welded Joints ◽  
Plate Thickness ◽  
Welding Process ◽  
Element Analysis

Welding is one of the most used joining methods in the ship industry. However, residual stresses are induced in the welded joints due to the rapid heating and cooling leading to inhomogenously distributed dimensional changes and non-uniform plastic and thermal strains. A number of factors, such as welding speed, boundary conditions, weld geometry, weld thickness, welding current/voltage, number of weld passes, pre-/post-heating etc, influence the residual stress distribution. The main aim of this work is to estimate the residual stresses in welded joints through finite element analysis and to investigate the effects of boundary conditions, welding speed and plate thickness on through the thickness/surface distributions of residual stresses. The welding process is simulated using 3D Finite element model in ABAQUS FE software in two steps: 1. Transient thermal analysis and 2. Quasi-static thermo-elasto-plastic analysis. The normal residual stresses along and across the weld in the weld tow region are found to be significant with nonlinear distribution. The residual stresses increase with the increase in the thickness of the plates being welded. The nature of the normal residual stress along the weld is found to be tensile-compressive-tensile and the nature of normal residual stress across the weld is found to be tensile along the thickness direction.

Sign in / Sign up

Export Citation Format

Share Document