An Experimental Study of Heat Pipe Performance Using Binary Mixture Fluids That Exhibit Strong Concentration Marangoni Effects

2011 ◽  
Vol 3 (3) ◽  
Author(s):  
Kenneth M. Armijo ◽  
Van P. Carey
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Heat Pipe ◽  
Pure Water ◽  
Working Fluid ◽  
Strong Concentration ◽  
Alcohol Mixtures ◽  
Marangoni Effects ◽  
Water Alcohol

This paper summarizes the results of an experimental investigation of the performance characteristics of a gravity/capillary driven heat pipe using water/alcohol mixtures as a working fluid. This investigation specifically explored the use of water/alcohol mixtures that exhibit strong concentration-based Marangoni effects. Experiments to determine heat pipe performance were conducted for pure water and water/alcohol solutions with increasing concentrations of alcohol. Initial tests with pure water determined the optimal working fluid charge for the heat pipe; subsequent performance tests over a wide range of heat input levels were then conducted for each working fluid at this optimum value. The results indicate that some mixtures can significantly enhance the heat transfer coefficient and heat flux capability of the heat pipe evaporator. For the best mixture tested, the maximum evaporator heat flux carried by the coolant without dryout was found to be 52% higher than the value for the same heat pipe using pure water as a coolant under comparable conditions. Peak evaporator heat flux values above 100 W/cm2 were achieved with some mixtures. Evaporator and condenser heat transfer coefficient data are presented, and the trends are examined in the context of the expected effect of the Marangoni mechanisms on heat transfer.

An Experimental Study of Heat Pipe Performance Using Binary Mixture Fluids That Exhibit Strong Concentration Marangoni Effects

2010 ◽  
Author(s):  
Kenneth M. Armijo ◽  
Van P. Carey
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Heat Pipe ◽  
Pure Water ◽  
Working Fluid ◽  
Strong Concentration ◽  
Alcohol Mixtures ◽  
Marangoni Effects ◽  
Water Alcohol

This paper summarizes the results of an experimental investigation of the performance characteristics of a gravity/capillary driven heat pipe using water/alcohol mixtures as a working fluid. This investigation specifically explored the use of water/alcohol mixtures that exhibit strong concentration-based Marangoni effects. Experiments to determine heat pipe performance were conducted for pure water and water/alcohol solutions with increasing concentrations of alcohol. Initial tests with pure water determined the optimal working fluid charge for the heat pipe; subsequent performance tests over a wide range of heat input rates were then conducted for each working fluid at this optimum value. The results indicate that some mixtures can significantly enhance the heat transfer coefficient and heat flux capability of the heat pipe evaporator. For the best mixture tested, the maximum evaporator heat flux carried by the coolant without dryout was found to be 52% higher than the value for the same heat pipe using pure water as a coolant under comparable conditions. Peak evaporator heat fluxes above 100 W/cm2 were achieved with some mixtures. Evaporator and condenser heat transfer coefficient data are presented and the trends are examined in the context of the expected effect of the Marangoni mechanisms on heat transfer. Heat pipe design features that take maximum advantage of Marangoni effects are described and the application of these types of heat pipes to electronics cooling and heat removal from concentrating photovoltaic systems is discussed.

scholarly journals The effect of operating parameters on the heat transfer in the heat pipe

2021 ◽  
Vol 2119 (1) ◽  
pp. 012088
Author(s):  
A. A. Litvintceva ◽  
N. I. Volkov ◽  
N. I. Vorogushina ◽  
V. A. Moskovskikh ◽  
V. V. Cheverda
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Temperature Difference ◽  
Heat Pipes ◽  
Working Fluid ◽  
Operating Parameters ◽  
Temperature Stabilization ◽  
Ir Camera ◽  
Fluid Properties

Abstract Heat pipes are a good solution for temperature stabilization, for example, of microelectronics, because these kinds of systems are without any moving parts. Experimental research of the effect of operating parameters on the heat transfer in a cylindrical heat pipe has been conducted. The effect of the working fluid properties and the porous layer thickness on the heat flux and temperature difference in the heat pipe has been investigated. The temperature field of the heat pipe has been investigated using the IR-camera and K-type thermocouples. The data obtained by IR-camera and K-type thermocouples have been compared. It is demonstrated the power transferred from the evaporator to the condenser is a linear function of the temperature difference between them.

Experimental Investigation of Oscillating Heat Pipe With Hybrid Fluids of Liquid Metal and Water

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Tingting Hao ◽  
Hongbin Ma ◽  
Xuehu Ma
Keyword(s):  
Heat Transfer ◽  
Liquid Metal ◽  
Heat Pipe ◽  
Heat Input ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Experimental Results ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe

A new oscillating heat pipe (OHP) charged with hybrid fluids can improve thermal performance. The key difference in this OHP is that it uses room temperature liquid metal (Galinstan consisting of gallium, indium, and tin) and water as the working fluid. The OHP was fabricated on a copper plate with six turns and a 3 × 3 mm2 cross section. The OHP with hybrid fluids as the working fluid was investigated through visual observation and thermal measurement. Liquid metal was successfully driven to flow through the OHP by the pressure difference between the evaporator and the condenser without external force. Experimental results show that while added liquid metal can increase the heat transport capability, liquid metal oscillation amplitude decreases as the filling ratio of liquid metal increases. Visualization of experimental results show that liquid metal oscillation position and velocity increase as the heat input increases. Oscillating motion of liquid metal in the OHP significantly increases the heat transfer performance at high heat input. The lowest thermal resistance of 0.076 °C/W was achieved in the hybrid fluids-filled OHP with a heat input of 420 W. We experimentally demonstrated a 13% higher heat transfer performance using liquid metal as the working fluid compared to an OHP charged with pure water.

Two Phase Heat Transfer of Ammonia in a Mini/Micro Channel

2010 ◽  
Author(s):  
M. Hamayun Maqbool ◽  
Bjo¨rn Palm ◽  
R. Khodabandeh ◽  
Rashid Ali
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Experimental Results ◽  
Working Fluid ◽  
Internal Diameter ◽  
Vapour Quality ◽  
The Heat Transfer Coefficient

Experiments have been performed to investigate heat transfer in a circular vertical mini channel made of stainless steel (AISI 316) with internal diameter of 1.70 mm and a uniformly heated length of 245 mm using ammonia as working fluid. The experiments are conducted for a heat flux range of 15 to 350 kW/m2 and mass flux range of 100 to 500 kg/m2s. The effects of heat flux, mass flux and vapour quality on the heat transfer coefficient are explored in detail. The experimental results show that the heat transfer coefficient increases with imposed wall heat flux while mass flux and vapour quality have no considerable effect. Experimental results are compared to predictive methods available in the literature for boiling heat transfer. The correlations of Cooper et al. [1] and Shah [3] are in good agreement with our experimental data.

Gravity-Assisted Heat Pipe With Strong Marangoni Fluid for Waste Heat Management of Single and Dual-Junction Solar Cells

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Kenneth M. Armijo ◽  
Van P. Carey
Keyword(s):  
Heat Flux ◽  
Solar Cells ◽  
Heat Pipe ◽  
Waste Heat ◽  
Working Fluid ◽  
Water Mixture ◽  
Heat Management ◽  
Strong Concentration ◽  
Electrical Efficiency ◽  
Pipe System

This study investigates the cooling of single and multijunction solar cells with an inclined, gravity-assisted heat pipe, containing a 0.05 M 2-propanol/water mixture that exhibits strong concentration Marangoni effects. Heat pipe solar collector system thermal behavior was investigated theoretically and semi-empirically through experimentation of varying input heat loads from attached strip-heaters to simulate waste heat generation of single-junction monocrystalline silicon (Si), and dual-junction GaInP/GaAs photovoltaic (PV) solar cells. Several liquid charge ratios were investigated to determine an optimal working fluid volume that reduces the evaporator superheat while enhancing the vaporization transport heat flux. Results showed that a 45% liquid charge, with a critical heat flux of 114.8 W/cm2, was capable of achieving the lowest superheat levels, with a system inclination of 37 deg. Solar cell semiconductor theory was used to evaluate the effects of increasing temperature and solar concentration on cell performance. Results showed that a combined PV/heat pipe system had a 1.7% higher electrical efficiency, with a concentration ratio 132 suns higher than the stand-alone system. The dual-junction system also exhibited enhanced performance at elevated system temperatures with a 2.1% greater electrical efficiency, at an operational concentration level 560 suns higher than a stand-alone system.

Thermal Characteristics of a Cylindrical Heat Pipe using Multi-Layer Screen Mesh Wick

2018 ◽  
Vol 10 (5) ◽  
Author(s):  
R. Sankar Rao ◽  
S. Bhanu Prakash
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Thermal Resistance ◽  
Transfer Coefficient ◽  
Heat Pipe ◽  
Thermal Characteristics ◽  
Wire Mesh ◽  
Working Fluid ◽  
Wick Structure ◽  
Screen Mesh

Heat pipe is the most widely used heat exchanging device in removal of heat from any given system at a faster rate. The thermal characteristics of heat pipe with single and multi-layered screen mesh wicks have been observed with two working fluids water and acetone. Heat pipe of length 250 mm and 12.7 mm outer diameter, made of copper material is used in all the trials of with and without wick structure. A 100 mesh stainless steel screen wire mesh is chosen as wick structure. Experiments were conducted at different heat loads and various inclinations with 100% fill ratio in evaporator. The performance is measured based on total thermal resistance and overall heat transfer coefficient. The heat pipe is found effective at 60o inclination with acetone as a working fluid and with four layered screen mesh wick. Uncertainty in thermal resistance and heat transfer coefficient is calculated for a heat input of 10W at 0 and 60 inclinations.

Working Fluid Inventory Effect on Heat Transfer Performance of a Grooved Micro Heat Pipe

2013 ◽  
Vol 589-590 ◽  
pp. 559-564
Author(s):  
Xi Bing Li ◽  
Yun Shi Ma ◽  
Xun Wang ◽  
Ming Li
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Mathematic Model ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Flux Concentration

As a highly efficient heat transfer component, a micro heat pipe (MHP) has been widely applied to the situations with high heat flux concentration. However, a MHPs heat transfer performance is affected by many factors, among which, working fluid inventory has great influence on the security, reliability and frost resistance of its heat transfer performance. In order to determine the appropriate working fluid inventory for grooved MHPs, this paper first analyzed the working principle, major heat transfer limits and heat flux distribution law of grooved MHPs in electronic chips with high heat flux concentration, then established a mathematic model for the working fluid inventory in grooved MHPs. Finally, with distilled water being the working fluid, a series of experimental investigations were conducted at different temperatures to test the heat transfer performances of grooved MHPs, which were perfused with different inventories and with different adiabatic section lengths. The experimental results show that when the value of α is roughly within 0.40±0.05, a grooved MHP can acquire its best heat transfer performance, and the working fluid inventory can be determined by the proposed mathematic model. Therefore this study solves the complicated problem of determining appropriate working fluid inventory for grooved MHPs.

The Effect of Inlet Orifice on Critical Heat Flux and Flow Boiling Heat Transfer in Single Horizontal Microtube

2013 ◽  
Author(s):  
Yanfeng Fan ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Saturation Pressure ◽  
Working Fluid ◽  
Flow Boiling Heat Transfer

Flow oscillation is a crucial issue for the development of flow boiling heat transfer in the applications. Inlet orifice has been proven be an option to eliminate the oscillation. However, the effects of inlet orifice on critical heat flux and flow boiling heat transfer coefficient are lack of study. In this work, the effects of inlet restriction on critical heat flux and heat transfer coefficient in single horizontal microtube under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two smaller microtubes are assembled at the inlet of main microtube to achieve the restriction configurations of 50% and 20% area ratios. The experimental measurement is carried out at mass fluxes ranging from 160–870 kg/m2·s and heat fluxes varying from 6–170 kW/m2. Two saturation pressures, 10 and 45 kPa, are tested. The experimental results of critical heat flux and two phase heat transfer coefficient obtained in the microtube without orifice are compared with the existing correlations. The addition of an orifice does not enhance the normal critical heat flux but increases the premature critical heat flux. In aspect of heat transfer, the orifice shows improvement on heat transfer coefficient at low mass flux and high saturation pressure.

An Experimental Investigation of a Low Heat Flux, Wickless Heat Pipe

1983 ◽  
Vol 7 (2) ◽  
pp. 96-99
Author(s):  
B.S. Larkin
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Transfer Coefficients ◽  
Electronic Package ◽  
Ambient Temperatures ◽  
Heat Transfer Coefficients ◽  
Flux Charge

This paper reports tests on a wickless heat pipe to be used for transporting heat from the ground to protect an electronic package from low ambient temperatures. Evaporating heat transfer coefficients were measured for low heat fluxes where the behaviour of the evaporating film is unpredictable. The effects of type of working fluid, heat flux, charge quantity and tube inclination were investigated.

Flow Boiling Heat Transfer Characteristics of a Minichannel Up to Dryout Condition

2009 ◽  
Author(s):  
Rashid Ali ◽  
Bjo¨rn Palm ◽  
Mohammad H. Maqbool
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Working Fluid ◽  
Flow Boiling Heat Transfer ◽  
The Heat Transfer Coefficient

In this paper the experimental flow boiling heat transfer results of a minichannel are presented. A series of experiments was conducted to measure the heat transfer coefficients in a minichannel made of stainless steel (AISI 316) having an internal diameter of 1.7mm and a uniformly heated length of 220mm. R134a was used as working fluid and experiments were performed at two different system pressures corresponding to saturation temperatures of 27 °C and 32 °C. Mass flux was varied from 50 kg/m2 s to 600 kg/m2 s and heat flux ranged from 2kW/m2 to 156kW/m2. The test section was heated directly using a DC power supply. The direct heating of the channel ensured uniform heating and heating was continued until dry out was reached. The experimental results show that the heat transfer coefficient increases with imposed wall heat flux while mass flux and vapour quality have no considerable effect. Increasing the system pressure slightly enhances the heat transfer coefficient. The heat transfer coefficient is reduced as dryout is reached. It is observed that dryout phenomenon is accompanied with fluctuations and a larger standard deviation in outer wall temperatures.

Sign in / Sign up

Export Citation Format

Share Document