A Review of High-Heat-Flux Heat Removal Technologies

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
M. A. Ebadian ◽  
C. X. Lin
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Heat Removal ◽  
High Heat ◽  
High Heat Flux ◽  
Phase Flow ◽  
Two Phase ◽  
Recent Developments ◽  
Removal Technologies

In recent years, high-heat-flux cooling techniques have received great attention from researchers around the world due to its importance in thermal management of both commercial and defense high-power electronic devices. Although impressive progress has been made during the last few decades, high-heat-flux removal still largely remains as a challenging subject that needs further exploration and study. In this paper, we have reviewed recent developments in several high-heat-flux heat removal techniques, including microchannels, jet impingements, sprays, wettability effects, and piezoelectrically driven droplets. High-heat-flux removal can be achieved effectively by either single-phase flow or two-phase flow boiling heat transfer. Better understandings of the underlying heat transfer mechanisms for performance improvement are discussed.

Flow Boiling Heat Transfer Enhancement in Subcooled and Saturated Refrigerants in Minichannel Heat Sinks

2014 ◽  
Author(s):  
Ehsan Yakhshi-Tafti ◽  
Howard Pearlman ◽  
Seung M. You
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
Heat Sinks ◽  
High Heat Flux ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Laser Applications ◽  
Enhanced Boiling

Forced two-phase cooling is investigated for handling high power electronics and laser applications having high heat flux and isothermality requirements. Experimental results are reported for minichannel heat sinks with and without enhanced boiling coatings showing increased heat transfer coefficients and higher critical heat flux for coated versus uncoated surfaces.

Study on onset of nucleate boiling with screw tube for fusion reactor application

2021 ◽  
Author(s):  
Ji Hwan Lim ◽  
Minkyu Park
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Transfer Mechanism ◽  
High Heat Flux ◽  
Heat Transfer Mechanism ◽  
System Parameters ◽  
Smooth Tubes

Abstract The onset of nucleate boiling (ONB) is the point at which the heat transfer mechanism in fluids changes and is one of the thermo-hydraulic factors that must be considered when establishing a cooling system operation strategy. Because the high heat flux of several MW/m2, which is loaded within a tokamak, is applied under a one-side heating condition, it is necessary to determine a correlative relation that can predict ONB under special heating conditions. In this study, the ONB of a one-side-heated screw tube was experimentally analyzed via a subcooled flow boiling experiment. The helical nut structure of the screw tube flow path wall allows for improved heat transfer performance relative to smooth tubes, providing a screw tube with a 53.98% higher ONB than a smooth tube. The effects of the system parameters on the ONB heat flux were analyzed based on the changes in the heat transfer mechanism, with the results indicating that the flow rate and degree of subcooling are proportional to the ONB heat flux because increasing these factors improves the forced convection heat transfer and increases the condensation rate, respectively. However, it was observed that the liquid surface tension and latent heat decrease as the pressure increases, leading to a decrease in the ONB heat flux. An evaluation of the predictive performance of existing ONB correlations revealed that most have high error rates because they were developed based on ONB experiments on micro-channels or smooth tubes and not under one-side high heat load conditions. To address this, we used dimensional analysis based on Python code to develop new ONB correlations that reflect the influence of system parameters.

Heat Transfer Enhancement in Compact Phase Change Microchannel Heat Exchangers for High Flux Laser Diodes

2018 ◽  
Author(s):  
Jensen Hoke ◽  
Todd Bandhauer ◽  
Jack Kotovsky ◽  
Julie Hamilton ◽  
Paul Fontejon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Flow Boiling ◽  
Laser Diodes ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Average Maximum

Liquid-vapor phase change heat transfer in microchannels offers a number of significant advantages for thermal management of high heat flux laser diodes, including reduced flow rates and near constant temperature heat rejection. Modern laser diode bars can produce waste heat loads >1 kW cm−2, and prior studies show that microchannel flow boiling heat transfer at these heat fluxes is possible in very compact heat exchanger geometries. This paper describes further performance improvements through area enhancement of microchannels using a pyramid etching scheme that increases heat transfer area by ∼40% over straight walled channels, which works to promote heat spreading and suppress dry-out phenomenon when exposed to high heat fluxes. The device is constructed from a reactive ion etched silicon wafer bonded to borosilicate to allow flow visualization. The silicon layer is etched to contain an inlet and outlet manifold and a plurality of 40μm wide, 200μm deep, 2mm long channels separated by 40μm wide fins. 15μm wide 150μm long restrictions are placed at the inlet of each channel to promote uniform flow rate in each channel as well as flow stability in each channel. In the area enhanced parts either a 3μm or 6μm sawtooth pattern was etched vertically into the walls, which were also scalloped along the flow path with the a 3μm periodicity. The experimental results showed that the 6μm area-enhanced device increased the average maximum heat flux at the heater to 1.26 kW cm2 using R134a, which compares favorably to a maximum of 0.95 kw cm2 dissipated by the plain walled test section. The 3μm area enhanced test sections, which dissipated a maximum of 1.02 kW cm2 showed only a modest increase in performance over the plain walled test sections. Both area enhancement schemes delayed the onset of critical heat flux to higher heat inputs.

Dependence of Heat Transfer Coefficient on Porous Structure in Porous Media

2008 ◽  
Author(s):  
Akira Matsui ◽  
Kazuhisa Yuki ◽  
Hidetoshi Hashizume
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Porous Media ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
High Performance ◽  
Heat Removal ◽  
High Heat ◽  
Metal Foams ◽  
High Heat Flux

Detailed heat transfer characteristics of particle-sintered porous media and metal foams are evaluated to specify the important structural parameters suitable for high heat removal. The porous media used in this experiment are particle-sintered porous media made of bronze and SUS316L, and metal foams made of copper and nickel. Cooling water flows into the porous medium opposite to heat flux input loaded by a plasma arcjet. The result indicates that the bronze-particle porous medium of 100μm in pore size shows the highest performance and achieves heat transfer coefficient of 0.035MW/m2K at inlet heat flux 4.6MW/m2. Compared with the heat transfer performance of copper fiber-sintered porous media, the bronze particlesintered ones give lower heat transfer coefficient. However, the stable cooling conditions that the heat transfer coefficient does not depend on the flow velocity, were confirmed even at heat flux of 4.6MW/m2 in case of the bronze particle-sintered media, while not in the case of the copper-fiber sintered media. This signifies the possibility that the bronze-particle sintered media enable much higher heat flux removal of over 10MW/m2, which could be caused by higher permeability of the particle-sintered pore structures. Porous media with high permeability provide high performance of vapor evacuation, which leads to more stable heat removal even under extremely high heat flux. On the other hand, the heat transfer coefficient of the metal foams becomes lower because of the lower capillary and fin effects caused by too high porosity and low effective thermal conductivity. It is concluded that the pore structure having high performance of vapor evacuation as well as the high capillary and high fin effects is appropriate for extremely high heat flux removal of over 10MW/m2.

A Numerical Model of a Reciprocating-Mechanism Driven Heat Loop for Two-Phase High Heat Flux Cooling

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Olubunmi Popoola ◽  
Ayobami Bamgbade ◽  
Yiding Cao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Numerical Model ◽  
Performance Optimization ◽  
Numerical Study ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Two Phase ◽  
Transfer Device

An effective design option for a cooling system is to use a two-phase pumped cooling loop to simultaneously satisfy the temperature uniformity and high heat flux requirements. A reciprocating-mechanism driven heat loop (RMDHL) is a novel heat transfer device that could attain a high heat transfer rate through a reciprocating flow of the two-phase working fluid inside the heat transfer device. Although the device has been tested and validated experimentally, analytical or numerical study has not been undertaken to understand its working mechanism and provide guidance for the device design. The objective of this paper is to develop a numerical model for the RMDHL to predict its operational performance under different working conditions. The developed numerical model has been successfully validated by the existing experimental data and will provide a powerful tool for the design and performance optimization of future RMDHLs. The study also reveals that the maximum velocity in the flow occurs near the wall rather than at the center of the pipe, as in the case of unidirectional steady flow. This higher velocity near the wall may help to explain the enhanced heat transfer of an RMDHL.

High heat flux flow boiling in silicon multi-microchannels – Part I: Heat transfer characteristics of refrigerant R236fa

2008 ◽  
Vol 51 (21-22) ◽  
pp. 5400-5414 ◽  
Author(s):  
Bruno Agostini ◽  
John Richard Thome ◽  
Matteo Fabbri ◽  
Bruno Michel ◽  
Daniele Calmi ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Heat Transfer Characteristics ◽  
Flux Flow ◽  
Transfer Characteristics
Sign in / Sign up

Export Citation Format

Share Document