A Calculation Tool of a Turbine Cooling Air Schedule for General Gas Turbine Simulation Algorithms

2011 ◽  
Vol 134 (4) ◽  
Author(s):  
Valerio Lallini ◽  
Jan Janikovic ◽  
Pericles Pilidis ◽  
Riti Singh ◽  
Panagiotis Laskaridis
Keyword(s):  
Gas Turbine ◽  
Operating Cost ◽  
Flight Path ◽  
Turbine Engine ◽  
Turbine Cooling ◽  
Cooling Flow ◽  
Conventional Cooling ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Cooling Air

A tool to evaluate the turbine cooling air schedule during the flight path is presented. The method is suitable for complex gas turbine engine models where accurate calculation of thermodynamic parameters of a cooling flow used for studies such as specific fuel consumption (SFC), lifing, and operating cost analysis. The method is also applicable for land-based gas turbine engines where the flight path is replaced by load pattern. The method can be employed even if only a little information about the engine is known. The calculation method has been investigated on a model of a high bypass ratio turbofan for long haul application. Using it with an aircraft model and after comparing to conventional cooling air simulations, the reduction of SFC during the flight path has been observed. A comparison has been performed on engine manufacturer’s public domain data where the method shows comparable value of total cooling air needed. The tool returns similar results but estimates a higher proportion of cooling air for the high pressure turbine nozzle guide vanes (NGV) compared with Young and Wilcock’s method.

Characteristics of Volcanic Ash in a Gas Turbine Combustor and Nozzle Guide Vanes

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Lei-Yong Jiang ◽  
Yinghua Han ◽  
Prakash Patnaik
Keyword(s):  
Gas Turbine ◽  
Volcanic Ash ◽  
Inlet Temperature ◽  
Gas Turbine Combustor ◽  
Flow Passage ◽  
Guide Vanes ◽  
Cooling Flow ◽  
Cooling Passage ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

To understand the physics of volcanic ash impact on gas turbine hot-components and develop much-needed tools for engine design and fleet management, the behaviors of volcanic ash in a gas turbine combustor and nozzle guide vanes (NGV) have been numerically investigated. High-fidelity numerical models are generated, and volcanic ash sample, physical, and thermal properties are identified. A simple critical particle viscosity—critical wall temperature model is proposed and implemented in all simulations to account for ash particles bouncing off or sticking on metal walls. The results indicate that due to the particle inertia and combustor geometry, the volcanic ash concentration in the NGV cooling passage generally increases with ash size and density, and is less sensitive to inlet velocity. It can reach three times as high as that at the air inlet for the engine conditions and ash properties investigated. More importantly, a large number of the ash particles entering the NGV cooling chamber are trapped in the cooling flow passage for all four turbine inlet temperature conditions. This may reveal another volcanic ash damage mechanism originated from engine cooling flow passage. Finally, some suggestions are recommended for further research and development in this challenging field. To the best of our knowledge, it is the first study on detailed ash behaviors inside practical gas turbine hot-components in the open literature.

Flow Field Simulations of a Gas Turbine Combustor

2002 ◽  
Vol 124 (3) ◽  
pp. 508-516 ◽  
Author(s):  
M. D. Barringer ◽  
O. T. Richard ◽  
J. P. Walter ◽  
S. M. Stitzel ◽  
K. A. Thole
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Large Scale ◽  
Guide Vane ◽  
Wall Region ◽  
Turbine Engine ◽  
Tunnel Section ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Combustor Liner

The flow field exiting the combustor in a gas turbine engine is quite complex considering the presence of large dilution jets and complicated cooling schemes for the combustor liner. For the most part, however, there has been a disconnect between the combustor and turbine when simulating the flow field that enters the nozzle guide vanes. To determine the effects of a representative combustor flow field on the nozzle guide vane, a large-scale wind tunnel section has been developed to simulate the flow conditions of a prototypical combustor. This paper presents experimental results of a combustor simulation with no downstream turbine section as a baseline for comparison to the case with a turbine vane. Results indicate that the dilution jets generate turbulence levels of 15–18% at the exit of the combustor with a length scale that closely matches that of the dilution hole diameter. The total pressure exiting the combustor in the near-wall region neither resembles a turbulent boundary layer nor is it completely uniform putting both of these commonly made assumptions into question.

Validation and Comparison of Strip Seal Designs for Gas Turbine Engine Nozzle Guide Vanes

2008 ◽  
Author(s):  
Arash Farahani ◽  
Peter Childs
Keyword(s):  
Gas Turbine ◽  
Guide Vane ◽  
Gas Turbine Engine ◽  
Experimental Comparison ◽  
Cfd Modelling ◽  
Guide Vanes ◽  
Turbine Engine ◽  
Seal Design ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

Strip seals are commonly used to prevent or limit leakage flows between nozzle guide vanes (NGV) and other gas turbine engine components that are assembled from individual segments. Leakage flow across, for example, a nozzle guide vane platform, leads to increased demands on the gas turbine engine internal flow system and a rise in specific fuel consumption (SFC). Careful attention to the flow characteristics of strip seals is therefore necessary. The very tight tolerances associated with strip seals provides a particular challenge to their characterisation. This paper reports the validation of CFD modelling for the case of a strip seal under very carefully controlled conditions. In addition, experimental comparison of three types of strip seal design, straight, arcuate, and cloth, is presented. These seals are typical of those used by competing manufacturers of gas turbine engines. The results show that the straight seal provides the best flow sealing performance for the controlled configuration tested, although each design has its specific merits for a particular application.

Study over thermal state of gas turbine engine metal-ceramic rotor blades and nozzle guide vanes under thermal shock and thermal-cyclic loading conditions

2004 ◽  
Vol 13 (2) ◽  
pp. 163-166
Author(s):  
A. V. Soudarev ◽  
A. A. Souryaninov ◽  
V. Ya. Podgorets ◽  
V. V. Grishaev ◽  
V.Yu Tikhoplav ◽  
...  
Keyword(s):  
Cyclic Loading ◽  
Thermal Shock ◽  
Gas Turbine ◽  
Thermal State ◽  
Rotor Blades ◽  
Guide Vanes ◽  
Turbine Engine ◽  
Metal Ceramic ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes

Short Helical Combustor: Concept Study of an Innovative Gas Turbine Combustor With Angular Air Supply

2015 ◽  
Vol 138 (3) ◽  
Author(s):  
B. Ariatabar ◽  
R. Koch ◽  
H.-J. Bauer ◽  
D.-A. Negulescu
Keyword(s):  
Gas Turbine ◽  
Scaling Laws ◽  
Generic Model ◽  
Reacting Flow ◽  
Air Supply ◽  
Tilting Angle ◽  
Annular Combustor ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Cooling Air

An innovative design of a gas turbine annular combustor is investigated analytically and numerically. Its principal feature is the helical arrangement of the burners around the turbine shaft. Hence, a shorter combustor with lower aerodynamic losses and cooling air demand might be realized. A generic model of the combustor is developed and analyzed by means of a parametric study. Scaling laws for the geometry of the flame tube and the burners are derived. Thereby, the relevant similarity parameters for fluid flow, combustion, and heat transfer are maintained constant. Subsequently, nonreacting and reacting flow regimes of selected design variants are numerically investigated. It is shown that a double annular (DA) configuration with a tilting angle of β = 45 deg, where circumferentially adjacent swirls are corotating and radially are counter-rotating, is the superior design in terms of (1) maintaining the relevant similarity rules, (2) size and location of the recirculation zones and swirl flames, and (3) flow pattern at the combustor exit. The deflection angle of the nozzle guide vanes (NGV) as well as the axial length of such a short helical combustor (SHC) could be reduced by approximately 30%.

Flow Field Simulations of a Gas Turbine Combustor

2001 ◽  
Author(s):  
M. D. Barringer ◽  
O. T. Richard ◽  
J. P. Walter ◽  
S. M. Stitzel ◽  
K. A. Thole
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Large Scale ◽  
Guide Vane ◽  
Wall Region ◽  
Turbine Engine ◽  
Tunnel Section ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Combustor Liner

The flow field exiting the combustor in a gas turbine engine is quite complex considering the presence of large dilution jets and complicated cooling schemes for the combustor liner. For the most part, however, there has been a disconnect between the combustor and turbine when simulating the flow field that enters the nozzle guide vanes. To determine the effects of a representative combustor flow field on the nozzle guide vane, a large-scale wind tunnel section has been developed to simulate the flow conditions of a prototypical combustor. This paper presents experimental results of a combustor simulation with no downstream turbine section as a baseline for comparison to the case with a turbine vane. Results indicate that the dilution jets generate turbulence levels of 15–18% at the exit of the combustor with a length scale that closely matches that of the dilution hole diameter. The total pressure exiting the combustor in the near wall region neither resembles a turbulent boundary layer nor is it completely uniform putting both of these commonly made assumptions into question.

Pulsed Impingement Turbine Cooling and its Effect on the Efficiency of Gas Turbines With Pressure Gain Combustion

2020 ◽  
Author(s):  
Nicolai Neumann ◽  
Dieter Peitsch ◽  
Arne Berthold ◽  
Frank Haucke ◽  
Panagiotis Stathopoulos
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Impingement Cooling ◽  
Turbine Cooling ◽  
Pressure Gain Combustion ◽  
Cooling Air ◽  
Gas Turbine Cycle ◽  
Cycle Efficiency

Abstract Performance improvements of conventional gas turbines are becoming increasingly difficult and costly to achieve. Pressure Gain Combustion (PGC) has emerged as a promising technology in this respect, due to the higher thermal efficiency of the respective ideal gas turbine cycle. Previous cycle analyses considering turbine cooling methods have shown that the application of pressure gain combustion may require more turbine cooling air. This has a direct impact on the cycle efficiency and reduces the possible efficiency gain that can potentially be harvested from the new combustion technology. Novel cooling techniques could unlock an existing potential for a further increase in efficiency. Such a novel turbine cooling approach is the application of pulsed impingement jets inside the turbine blades. In the first part of this paper, results of pulsed impingement cooling experiments on a curved plate are presented. The potential of this novel cooling approach to increase the convective heat transfer in the inner side of turbine blades is quantified. The second part of this paper presents a gas turbine cycle analysis where the improved cooling approach is incorporated in the cooling air calculation. The effect of pulsed impingement cooling on the overall cycle efficiency is shown for both Joule and PGC cycles. In contrast to the authors’ anticipation, the results suggest that for relevant thermodynamic cycles pulsed impingement cooling increases the thermal efficiency of Joule cycles more significantly than it does in the case of PGC cycles. Thermal efficiency improvements of 1.0 p.p. for pure convective cooling and 0.5 p.p. for combined convective and film with TBC are observed for Joule cycles. But just up to 0.5 p.p. for pure convective cooling and 0.3 p.p. for combined convective and film cooling with TBC are recorded for PGC cycles.

Experimental Analysis of an Ultra Compact Combustor Powered Turbine Engine

2019 ◽  
Author(s):  
Brian T. Bohan ◽  
Marc D. Polanka
Keyword(s):  
Engine Performance ◽  
Combustion Products ◽  
Combustion Efficiency ◽  
Small Scale ◽  
Engine Operation ◽  
Turbine Engine ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Length Reduction ◽  
Outside Diameter

Abstract The innovative Ultra Compact Combustor (UCC) is an alternative to traditional turbine engine combustors and has been shown to reduce the combustor volume and offer potential improvements in combustion efficiency. Prior UCC configurations featured a circumferential combustion cavity positioned around the outside diameter (OD) of the engine. This configuration would be difficult to implement in a vehicle with a small, fixed diameter and had difficulty migrating the hot combustion products at the OD radially inward across an axial core flow to present a uniform temperature distribution to the first turbine stage. The present study experimentally tested a new UCC configuration that featured a circumferential cavity that exhausted axially into a dilution zone positioned just upstream of the nozzle guide vanes. The combustor was sized as a replacement burner for the JetCat P90 RXi small-scale turbine engine and fit inside the engine casing. This combustor configuration achieved a 33% length reduction compared to the stock JetCat combustor and achieved comparable engine performance across a limited operating range. Self-sustaining engine operation was achieved with a rotating compressor and turbine making this study the first to achieve operation of a UCC powered turbine engine.

Failure Analysis of Heavy Industrial Gas Turbine Engine First Stage Nozzel Guide Vane

2012 ◽  
Vol 445 ◽  
pp. 1047-1052
Author(s):  
Alaaeldin H. Mustafa
Keyword(s):  
Failure Analysis ◽  
Gas Turbine ◽  
Guide Vane ◽  
Xrd Analysis ◽  
Optical Microscope ◽  
Guide Vanes ◽  
X Ray ◽  
Nozzle Guide ◽  
Industrial Gas Turbine ◽  
Nozzle Guide Vanes

Failure analysis investigation was conducted on 70 MW set of 1st stage turbine nozzle guide vanes (NGVs) of heavy industrial gas turbine. The failure was investigated using the light optical microscope (LOM), X-ray diffraction analysis (XRD) and energy dispersive X-ray spectroscopy (EDS) in an environmental scanning electron microscope (ESEM). The results of the analysis indicate that the NGVs which were made of Co base superalloy FSX-414 had been operated above the recommended operating hours under different fuel types in addition to inadequate repair process in previous repair removal. The XRD analysis of the fractured areas sample shows presence ofwhich might indicate the prolonged operation at high temperature. Keywords: cobalt-base; nozzle guide vanes, gas turbine.

Sign in / Sign up

Export Citation Format

Share Document