Aerodynamics and Heat Transfer for a Cooled One and One-Half Stage High-Pressure Turbine—Part I: Vane Inlet Temperature Profile Generation and Migration

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
R. M. Mathison ◽  
C. W. Haldeman ◽  
M. G. Dunn
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Temperature Profile ◽  
Film Cooling ◽  
Leading Edge ◽  
Inlet Temperature ◽  
Temperature Profiles ◽  
Fluid Temperature ◽  
High Pressure Turbine ◽  
Wide Range

As controlled laboratory experiments using full-stage turbines are expanded to replicate more of the complicated flow features associated with real engines, it is important to understand the influence of the vane inlet temperature profile on the high-pressure vane and blade heat transfer as well as its interaction with film cooling. The temperature distribution of the incoming fluid governs not only the input conditions to the boundary layer but also the overall fluid migration. Both of these mechanisms have a strong influence on surface heat flux and therefore component life predictions. To better understand the role of the inlet temperature profile, an electrically heated combustor emulator capable of generating uniform, radial, or hot streak temperature profiles at the high-pressure turbine vane inlet has been designed, constructed, and operated over a wide range of conditions. The device is shown to introduce a negligible pressure distortion while generating the inlet temperature conditions for a stage-and-a-half turbine operating at design-corrected conditions. For the measurements described here, the vane is fully cooled and the rotor purge flow is active, but the blades are uncooled. Detailed temperature measurements are obtained at rake locations upstream and downstream of the turbine stage as well as at the leading edge and platform of the blade in order to characterize the inlet temperature profile and its migration. The use of miniature butt-welded thermocouples at the leading edge and on the platform (protruding into the flow) on a rotating blade is a novel method of mapping a temperature profile. These measurements show that the reduction in fluid temperature due to cooling is similar in magnitude for both uniform and radial vane inlet temperature profiles.

Aerodynamics and Heat Transfer for a Cooled One and One-Half Stage High-Pressure Turbine: Part I—Vane Inlet Temperature Profile Generation and Migration

2010 ◽  
Author(s):  
R. M. Mathison ◽  
C. W. Haldeman ◽  
M. G. Dunn
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Temperature Profile ◽  
Film Cooling ◽  
Leading Edge ◽  
Inlet Temperature ◽  
Fluid Temperature ◽  
High Pressure Turbine ◽  
Wide Range ◽  
And Migration

As controlled laboratory experiments using full-stage turbines are expanded to replicate more of the complicated flow features associated with real engines, it is important to understand the influence of the vane inlet temperature profile on the high-pressure vane and blade heat transfer as well as its interaction with film cooling. The temperature distribution of the incoming fluid governs not only the input conditions to the boundary layer but overall fluid migration. Both of these mechanisms have a strong influence on surface heat flux and therefore component life predictions. To better understand the role of the inlet temperature profile, an electrically heated combustor emulator capable of generating uniform, radial, or hot-streak temperature profiles at the high-pressure turbine vane inlet has been designed, constructed, and operated over a wide range of conditions. The device is shown to introduce a negligible pressure distortion while generating the inlet temperature conditions for a stage-and-a-half turbine operating at design-corrected conditions. For the measurements described here, the vane is fully cooled and the rotor purge flow is active but the blades are un-cooled. Detailed temperature measurements are obtained at rake locations upstream and downstream of the turbine stage as well as at the leading edge and platform of the blade in order to characterize the inlet temperature profile and its migration. The use of miniature butt-welded thermocouples at the leading edge and on the platform (protruding into the flow) on a rotating blade is a novel method of mapping temperature profile. These measurements show that the reduction in fluid temperature due to cooling is similar in magnitude for both a uniform and radial vane inlet temperature profile.

THE INFLUENCE OF PURGE FLOW PARAMETERS ON HEAT TRANSFER AND FILM COOLING IN TURBINE CENTER FRAMES

2021 ◽  
pp. 1-26
Author(s):  
Patrick René Jagerhofer ◽  
Marios Patinios ◽  
Tobias Glasenapp ◽  
Emil Goettlich ◽  
Federica Farisco
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Density Ratio ◽  
Constant Heat Flux ◽  
Inlet Temperature ◽  
High Pressure Turbine ◽  
Turbofan Engines ◽  
Blowing Ratio ◽  
Purge Flow

Abstract The imperative improvement in the efficiency of turbofan engines is commonly facilitated by increasing the turbine inlet temperature. This development has reached a point where also components downstream of the high-pressure turbine have to be adequately cooled. Such a component is the turbine center frame (TCF), known for a complex aerodynamic flow highly influenced by purge-mainstream interactions. The purge air, being injected through the wheelspace cavities of the upstream high-pressure turbine, bears a significant cooling potential for the TCF. Despite this, fundamental knowledge of the influencing parameters on heat transfer and film cooling in the TCF is still missing. This paper examines the influence of purge-to-mainstream blowing ratio, density ratio and purge swirl angle on heat transfer and film cooling in the TCF. The experiments are conducted in a sector-cascade test rig specifically designed for such heat transfer studies using infrared thermography and tailor-made flexible heating foils with constant heat flux. Three purge-to-mainstream blowing ratios and an additional no purge case are investigated. The purge flow is injected without swirl and also with engine-similar swirl angles. The purge swirl and blowing ratio significantly impact the magnitude and the spread of film cooling in the TCF. Increasing blowing ratios lead to an intensification of heat transfer. By cooling the purge flow, a moderate variation in purge-to-mainstream density ratio is investigated, and the influence is found to be negligible.

Heat Transfer and Film Cooling of Blade Tips and Endwalls

2011 ◽  
Vol 134 (4) ◽  
Author(s):  
S. Naik ◽  
C. Georgakis ◽  
T. Hofer ◽  
D. Lengani
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Leading Edge ◽  
Pressure Side ◽  
High Pressure Turbine ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blade Tip

This paper investigates the flow, heat transfer, and film cooling effectiveness of advanced high pressure turbine blade tips and endwalls. Two blade tip configurations have been studied, including a full rim squealer and a partial squealer with leading edge and trailing edge cutouts. Both blade tip configurations have pressure side film cooling and cooling air extraction through dust holes, which are positioned along the airfoil camber line on the tip cavity floor. The investigated clearance gap and the blade tip geometry are typical of that commonly found in the high pressure turbine blades of heavy-duty gas turbines. Numerical studies and experimental investigations in a linear cascade have been conducted at a blade exit isentropic Mach number of 0.8 and a Reynolds number of 9×105. The influence of the coolant flow ejected from the tip dust holes and the tip pressure side film holes has also been investigated. Both the numerical and experimental results showed that there is a complex aerothermal interaction within the tip cavity and along the endwall. This was evident for both tip configurations. Although the global heat transfer and film cooling characteristics of both blade tip configurations were similar, there were distinct local differences. The partial squealer exhibited higher local film cooling effectiveness at the trailing edge but also low values at the leading edge. For both tip configurations, the highest heat transfer coefficients were located on the suction side rim within the midchord region. However, on the endwall, the highest heat transfer rates were located close to the pressure side rim and along most of the blade chord. Additionally, the numerical results also showed that the coolant ejected from the blade tip dust holes partially impinges onto the endwall.

scholarly journals Computational Modeling and Thermal Paint Verification of Film-Cooling Designs for an Unshrouded High-Pressure Turbine Blade

1999 ◽  
Author(s):  
Steven G. Gegg ◽  
Nathan J. Heidegger ◽  
Ronald A. Mikkelson
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Turbine Blade ◽  
Film Cooling ◽  
Data Exchange ◽  
Turbine Blades ◽  
Inlet Temperature ◽  
High Pressure Turbine ◽  
Extreme High Temperature ◽  
Blade Tip

High pressure turbine blades are exposed to an extreme high temperature environment due to increasing turbine inlet temperature. High heat fluxes are likely on the blade pressure surface. Other regions, such as the trailing edge and blade tip may be difficult to cool uniformly. Unshrouded blades present an additional challenge due to the pressure driven transport of hot gas across the blade tip. The blade tip region is therefore prone to severe thermal stress, fatigue and oxidation. In order to develop effective cooling methods, designers require detailed flow and heat transfer information. This paper reports on computational aerodynamics and heat transfer studies for an unshrouded high pressure turbine blade. The emphasis is placed on the application of appropriate 3-D models for the prediction of airfoil surface temperatures. Details of the film cooling model, boundary conditions and data exchange with heat transfer models are described. The analysis approach has been refined for design use to provide timely and accurate results. Film cooling designs are to be tailored for the best coverage of the blade tip region. Designs include near-tip pressure side films and blade tip cooling holes. Hole placement and angle are investigated to achieve the best coolant coverage on the blade tip. Analytical results are compared to a thermal paint test on engine hardware. In addition to film cooling strategies, other aerodynamic/heat transfer design approaches are discussed to address the cooling requirements for an unshrouded blade.

Heat Transfer for the Blade of a Cooled Stage and One-Half High-Pressure Turbine—Part I: Influence of Cooling Variation

2011 ◽  
Vol 134 (3) ◽  
Author(s):  
R. M. Mathison ◽  
C. W. Haldeman ◽  
M. G. Dunn
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
High Pressure ◽  
Inlet Temperature ◽  
Temperature Profiles ◽  
High Pressure Turbine ◽  
Suction Surface ◽  
Adiabatic Wall ◽  
Cooling Flows ◽  
Cooling Flow

Heat-flux measurements are presented for a one-and-one-half stage high-pressure turbine operating at design-corrected conditions with modulated cooling flows in the presence of different inlet temperature profiles. Coolant is supplied from a heavily film-cooled vane and the purge cavity (between the rotor disk and the upstream vane) but not from the rotor blades, which are solid metal. Thin-film heat-flux gauges are located on the uncooled blade pressure and suction surface (at multiple span locations), on the blade tip, on the blade platform, and on the disk and vane sides of the purge cavity. These measurements provide a comprehensive picture of the effect of varying cooling flow rates on surface heat transfer to the turbine blade for uniform and radial inlet temperature profiles. Part I of this paper examines the macroscopic influence of varying all cooling flows together, while Part II investigates the individual regions of influence of the vane outer and purge cooling circuits in more detail. The heat-flux gauges are able to track the cooling flow over the suction surface of the airfoil as it wraps upwards along the base of the airfoil for the uniform vane inlet temperature profile. A similar comparison for the radial profile shows the same coolant behavior but with less pronounced changes. From these comparisons, it is clear that cooling impacts each temperature profile similarly. Nearly all of the cooling influence is limited to the blade suction surface, but small changes are observed for the pressure surface. In addition to the cooling study, a novel method of calculating the adiabatic wall temperature is demonstrated. The derived adiabatic wall temperature distribution shows very similar trends to the Stanton number distribution on the blade.

Heat Transfer and Film Cooling of Blade Tips and Endwalls

2010 ◽  
Author(s):  
S. Naik ◽  
C. Georgakis ◽  
T. Hofer ◽  
D. Lengani
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Leading Edge ◽  
Pressure Side ◽  
High Pressure Turbine ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blade Tip

This paper investigates the flow, heat transfer and film cooling effectiveness of advanced high-pressure turbine blade tips and endwall. Two blade tip configurations have been studied, including a full rim squealer and a partial squealer with a leading edge and trailing edge cut-out. Both blade tip configurations have pressure side film cooling, and cooling air extraction through dust holes which are positioned along the airfoil camber line on the tip cavity floor. The investigated clearance gap and the blade tip geometry are typical of that commonly found in the high pressure turbine blades of heavy-duty gas turbines. Numerical studies and experimental investigations in a linear cascade have been conducted at a blade exit isentropic Mach number of 0.8 and a Reynolds number of 9 × 105. The influence of the coolant flow ejected from the tip dust holes and the tip pressure side film holes has also been investigated. Both the numerical and experimental results showed that there is a complex aero-thermal interaction within the tip cavity and along the endwall. This was evident for both tip configurations. Although, the global heat transfer and film cooling characteristics of both blade tip configurations were similar, there were distinct local differences. The partial squealer exhibited higher local film cooling effectiveness at the trailing edge but also low values at the leading edge. For both tip configurations, the highest heat transfer coefficients were located on the suction side rim within the mid-chord region. However on the endwall, the highest heat transfer rates were located close to the pressure side rim and along most of the blade chord. Additionally, the numerical results also showed that the coolant ejected from the blade tip dust holes partially impinges onto the endwall.

Heat Transfer for the Blade of a Cooled Stage and One-Half High-Pressure Turbine: Part I—Influence of Cooling Variation

2010 ◽  
Author(s):  
R. M. Mathison ◽  
C. W. Haldeman ◽  
M. G. Dunn
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
High Pressure ◽  
Inlet Temperature ◽  
Temperature Profiles ◽  
High Pressure Turbine ◽  
Suction Surface ◽  
Adiabatic Wall ◽  
Cooling Flows ◽  
Cooling Flow

Heat-flux measurements are presented for a one-and-one-half stage high-pressure turbine operating at design corrected conditions with modulated cooling flows in the presence of different inlet temperature profiles. Coolant is supplied from a heavily film cooled vane and the purge cavity (between the rotor disk and the upstream vane) but not from the rotor blades, which are solid metal. Thin-film heat-flux gauges are located on the un-cooled blade pressure and suction surface (at multiple span locations), on the blade tip, on the blade platform, and on the disk and vane sides of the purge cavity. These measurements provide a comprehensive picture of the effect of varying cooling flow rates on surface heat transfer to the turbine blade for uniform and radial inlet temperature profiles. Part I of this paper examines the macroscopic influence of varying all cooling flows together, while Part II investigates the individual regions of influence of the vane outer and purge cooling circuits in more detail. The heat-flux gauges are able to track the cooling flow over the suction surface of the airfoil as it wraps upwards along the base of the airfoil for the uniform vane inlet temperature profile. A similar comparison for the radial profile shows the same coolant behavior but with less pronounced changes. From these comparisons, it is clear that cooling impacts each temperature profile similarly. Nearly all of the cooling influence is limited to the blade suction surface, but small changes are observed for the pressure surface. In addition to the cooling study, a novel method of calculating the adiabatic wall temperature is demonstrated. The derived adiabatic wall temperature distribution shows very similar trends to the Stanton Number distribution on the blade.

Developing a Combustor Simulator for Investigating High Pressure Turbine Aerodynamics and Heat Transfer

2004 ◽  
Author(s):  
M. D. Barringer ◽  
K. A. Thole ◽  
M. D. Polanka
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Test Facility ◽  
Temperature Profiles ◽  
High Pressure Turbine ◽  
Blow Down ◽  
Turbine Engine ◽  
The Impact

Within a gas turbine engine, the high pressure turbine vanes are subjected to very harsh conditions from the highly turbulent and hot gases exiting the combustor. The temperature and pressure fields exiting the combustor dictate the heat transfer and aero losses that occur in the turbine passages. To better understand these effects, the goal of this work is to develop an adjustable combustor exit profile simulator for the Turbine Research Facility (TRF) at the Air Force Research Laboratory (AFRL). The TRF is a high temperature, high pressure, short duration blow-down test facility that is capable of matching several aerodynamic and thermal non-dimensional engine parameters including Reynolds number, Mach number, pressure ratio, corrected mass flow, gas-to-metal temperature ratio, and corrected speed. The research objective was to design, install, and verify a non-reacting simulator device that provides representative combustor exit total pressure and temperature profiles to the inlet of the TRF turbine test section. This required the upstream section of the facility to be redesigned into multiple concentric annuli that serve the purpose of injecting high momentum dilution jets and low momentum film cooling jets into a central annular chamber, similar to a turbine engine combustor. The design of the simulator allows for variations in injection levels to generate turbulence and pressure profiles. It also can vary the dilution and film cooling temperatures to create a variety of temperature profiles consistent with real combustors. To date, the design and construction of the simulator device has been completed. All of the hardware has been trial fitted and the flow control shutter systems have been successfully installed and tested. Currently, verification testing is being performed to investigate the impact of the generated temperature, pressure, and turbulence profiles on turbine heat transfer and secondary flow development.

Clocking Effects of Inlet Non-Uniformities in a Fully Cooled High-Pressure Vane: A Conjugate Heat Transfer Analysis

2015 ◽  
Author(s):  
Duccio Griffini ◽  
Massimiliano Insinna ◽  
Simone Salvadori ◽  
Francesco Martelli
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cooling System ◽  
Hot Spot ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Heat Transfer Analysis

A high-pressure vane equipped with a realistic film-cooling configuration has been studied. The vane is characterized by the presence of multiple rows of fan-shaped holes along pressure and suction side while the leading edge is protected by a showerhead system of cylindrical holes. Steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) simulations have been performed. A preliminary grid sensitivity analysis with uniform inlet flow has been used to quantify the effect of spatial discretization. Turbulence model has been assessed in comparison with available experimental data. The effects of the relative alignment between combustion chamber and high-pressure vanes are then investigated considering realistic inflow conditions in terms of hot spot and swirl. The inlet profiles used are derived from the EU-funded project TATEF2. Two different clocking positions are considered: the first one where hot spot and swirl core are aligned with passage and the second one where they are aligned with the leading edge. Comparisons between metal temperature distributions obtained from conjugate heat transfer simulations are performed evidencing the role of swirl in determining both the hot streak trajectory within the passage and the coolant redistribution. The leading edge aligned configuration is resulted to be the most problematic in terms of thermal load, leading to increased average and local vane temperature peaks on both suction side and pressure side with respect to the passage aligned case. A strong sensitivity of both injected coolant mass flow and heat removed by heat sink effect has also been highlighted for the showerhead cooling system.

The Influence of Purge Flow Parameters on Heat Transfer and Film Cooling in Turbine Center Frames

2021 ◽  
Author(s):  
Patrick R. Jagerhofer ◽  
Marios Patinios ◽  
Tobias Glasenapp ◽  
Emil Göttlich ◽  
Federica Farisco
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Convective Heat Transfer Coefficient ◽  
Density Ratio ◽  
Constant Heat Flux ◽  
High Pressure Turbine ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Purge Flow

Abstract Due to stringent environmental legislation and increasing fuel costs, the efficiencies of modern turbofan engines have to be further improved. Commonly, this is facilitated by increasing the turbine inlet temperatures in excess of the melting point of the turbine components. This trend has reached a point where not only the high-pressure turbine has to be adequately cooled, but also components further downstream in the engine. Such a component is the turbine center frame (TCF), having a complex aerodynamic flow field that is also highly influenced by purge-mainstream interactions. The purge air, being injected through the wheelspace cavities of the upstream high-pressure turbine, bears a significant cooling potential for the TCF. Despite this, fundamental knowledge of the influencing parameters on heat transfer and film cooling in the TCF is still missing. This paper examines the influence of purge-to-mainstream blowing ratio, purge-to-mainstream density ratio and purge flow swirl angle on the convective heat transfer coefficient and the film cooling effectiveness in the TCF. The experiments are conducted in a sector-cascade test rig specifically designed for such heat transfer studies using infrared thermography and tailor-made flexible heating foils with constant heat flux. The inlet flow is characterized by radially traversing a five-hole-probe. Three purge-to-mainstream blowing ratios and an additional no purge case are investigated. The purge flow is injected without swirl and also with engine-similar swirl angles. The purge swirl and blowing ratio significantly impact the magnitude and the spread of film cooling in the TCF. Increasing blowing ratios lead to an intensification of heat transfer. By cooling the purge flow, a moderate variation in purge-to-mainstream density ratio is investigated, and the influence is found to be negligible.

Sign in / Sign up

Export Citation Format

Share Document