Repeatability Estimation in Galling Resistance Testing

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Scott R. Hummel ◽  
Jeffrey Helm
Keyword(s):  
Probabilistic Approach ◽  
Surface Damage ◽  
Severe Form ◽  
Test Method ◽  
Resistance Testing ◽  
Test Results ◽  
Analysis Method ◽  
Astm Method ◽  
Mechanical Surface ◽  
Extensive Plastic Deformation

Galling is a severe form of mechanical surface damage, commonly observed in metals, that is accompanied by adhesive transfer, extensive plastic deformation, and/or cold-welding of the mating surfaces. It can lead to seizure or rapid failure of machine components. Stainless steels are particularly prone to galling. A new galling test and analysis method that reflects the statistical nature of galling is described. The new ASTM method (G196), which embodies a probabilistic approach to galling, is superior to an older ASTM test method (G98), which produces only a single threshold stress for a given combination of materials. A computer-modeled experiment involving a 300 series stainless steel is used to illustrate how the enhanced analysis can be applied to determine the repeatability of galling test results.

Variasi Penambahan Sika Cim Dan Fiber Kawat Pada Beton Mutu Fc’ 30 Mpa

2018 ◽  
Vol 9 (2) ◽  
pp. 67-73
Author(s):  
M Zainul Arifin
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Astm Method ◽  
Additive Type ◽  
Composition Variation ◽  
Compressive Strength Of Concrete

This research was conducted to determine the value of the highest compressive strength from the ratio of normal concrete to normal concrete plus additive types of Sika Cim with a composition variation of 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1 , 50% and 1.75% of the weight of cement besides that in this study also aims to find the highest tensile strength from the ratio of normal concrete to normal concrete in the mixture of sika cim composition at the highest compressive strength above and after that added fiber wire with a size diameter of 1 mm in length 100 mm with a ratio of 1% of material weight. The concrete mix plan was calculated using the ASTM method, the matrial composition of the normal concrete mixture as follows, 314 kg / m3 cement, 789 kg / m3 sand, 1125 kg / m3 gravel and 189 liters / m3 of water at 10 cm slump, then normal concrete added variations of the composition of sika cim 0.25%, 0.50%, 0.75%, 1.00%, 1.25%, 1.5%, 1.75% by weight of cement and fiber, the tests carried out were compressive strength of concrete and tensile strength of concrete, normal maintenance is soaked in fresh water for 28 days at 30oC. From the test results it was found that the normal concrete compressive strength at the age of 28 days was fc1 30 Mpa, the variation in the addition of the sika cim additive type mineral was achieved in composition 0.75% of the cement weight of fc1 40.2 Mpa 30C. Besides that the tensile strength test results were 28 days old with the addition of 1% fiber wire mineral to the weight of the material at a curing temperature of 30oC of 7.5%.

PENGARUH CITRA MEREK DAN KUALITAS PRODUK TERHADAP KEPUTUSAN PEMBELIAN MOBIL MITSUBISHI PADA PT. KRAMA YUDHA MOTORS AND MANFACTURING

2018 ◽  
Vol 6 (1) ◽  
Author(s):  
Nuridin, SE., MM. ◽  
Dwi Ardika Prayudha
Keyword(s):  
Product Quality ◽  
Brand Image ◽  
Linear Regression Analysis ◽  
Multiple Linear Regression Analysis ◽  
Coefficient Of Determination ◽  
Purchase Decision ◽  
Test Results ◽  
Analysis Method ◽  
Validity And Reliability ◽  
Image Variables

This research is aimed to examine the influence of brand image and product quality to car purchase decision at PT. Mitsubishi Krama Yudha Motors and Manufacturing. Data analysis method was used, is quantitative analysis, by using validity and reliability test, coefficient of determination, and multiple linear regression analysis. Result of regression equation is: Y = 0,665 + 0,517 X1 + 0,416 X2 Simultaneously testing of brand image variables and product quality to purchase decision, shown by F count equal to 85,955 bigger than F table 3,159 or with sig. F 0.000 is smaller than alpha 0.005. Based on the test results simultaneously, can be seen that the independent variables (brand image and product quality) have a positive and significant impact on the car purchase decision at Mitsubishi cars At PT. Krama Yudha Motors and Manufacturing. Suggestions which can be given for future developments and determinations of policy are, companies should pay attention to brand image, product quality, to make customers more satisfied and keep using Mitsubishi cars as their choice.

Characterization of Antibacterial-Producing Endophytic Fungi of Syzygiumpolyanthum Leaves

2020 ◽  
Vol 20 (4) ◽  
pp. 448-454
Author(s):  
Rahmita Burhamzah ◽  
Gemini Alam ◽  
Herlina Rante
Keyword(s):  
Molecular Characterization ◽  
Endophytic Fungi ◽  
Morphological Characterization ◽  
Test Method ◽  
Analysis Method ◽  
Nitrogen Base ◽  
Rdna Genes ◽  
Antibacterial Screening ◽  
Planting Method

Background: Endophytic fungi live in plants’ tissue and can produce the same bioactive compounds as its host plant produces. Syzygiumpolyanthum leaves have known to be one of the antibacterial compound producers. Aim and Objective: This study aimed to characterize morphologically, microscopically, and molecularly the antibacterial-producing endophytic fungi of Syzygiumpolyanthum leaves. Methods: The isolation of endophytic fungi was done by fragment planting method on PDA medium. The antibacterial screening was performed using the antagonistic test as the first screening followed by the disc diffusion test method. The morphological characterization was based on isolate’s mycelia color, growth pattern, margin, and surface texture of the colony, while the microscopic characterization was based on its hyphae characteristics. The molecular characterization of the isolate was done by nitrogen base sequence analysis method on nucleotide constituent of ITS rDNA genes of the isolate. Results: The results found that isolate DF1 has antibacterial activity against E.coli, S.aureus, P.acne, and P.aeruginosa, with the greatest inhibition at 10% concentration of broth fermentation extract on S.aureus with a diameter of inhibition of 13.77 mm. Conclusion: Based on macroscopic, microscopic, and molecular characterization, DF1 isolate is similar to Ceriporialacerate.

scholarly journals Antimicrobial resistance profile and multidrug resistance patterns of Streptococcus pneumoniae isolates from patients suspected of pneumococcal infections in Ethiopia

2021 ◽  
Vol 20 (1) ◽  
Author(s):  
Bekele Sharew ◽  
Feleke Moges ◽  
Gizachew Yismaw ◽  
Wondwossen Abebe ◽  
Surafal Fentaw ◽  
...  
Keyword(s):  
Multidrug Resistance ◽  
Streptococcus Pneumoniae ◽  
Antimicrobial Resistance ◽  
Addis Ababa ◽  
Pneumococcal Infection ◽  
Test Method ◽  
Resistance Testing ◽  
Global Public Health ◽  
Pneumococcal Infections ◽  
Resistance Patterns

Abstract Background Antimicrobial-resistant strains of Streptococcus pneumoniae have become one of the greatest challenges to global public health today and inappropriate use of antibiotics and high level of antibiotic use is probably the main factor driving the emergence of resistance worldwide. The aim of this study is, therefore, to assess the antimicrobial resistance profiles and multidrug resistance patterns of S. pneumoniae isolates from patients suspected of pneumococcal infections in Ethiopia. Methods A hospital-based prospective study was conducted from January 2018 to December 2019 at Addis Ababa city and Amhara National Region State Referral Hospitals. Antimicrobial resistance tests were performed from isolates of S. pneumoniae that were collected from pediatric and adult patients. Samples (cerebrospinal fluid, blood, sputum, eye discharge, ear discharge, and pleural and peritoneal fluids) from all collection sites were initially cultured on 5% sheep blood agar plates and incubated overnight at 37 °C in a 5% CO2 atmosphere. Streptococcus pneumoniae was identified and confirmed by typical colony morphology, alpha-hemolysis, Gram staining, optochin susceptibility, and bile solubility test. Drug resistance testing was performed using the E-test method according to recommendations of the Clinical and Laboratory Standards Institute. Results Of the 57 isolates, 17.5% were fully resistant to penicillin. The corresponding value for both cefotaxime and ceftriaxone was 1.8%. Resistance rates to erythromycin, clindamycin, tetracycline, chloramphenicol and trimethoprim-sulfamethoxazole were 59.6%, 17.5%, 38.6%, 17.5 and 24.6%, respectively. Multidrug resistance (MDR) was seen in 33.3% isolates. The most common pattern was co-resistance to penicillin, erythromycin, clindamycin, and tetracycline. Conclusions Most S. pneumoniae isolates were susceptible to ceftriaxone and cefotaxime. Penicillin has been used as a drug of choice for treating S. pneumoniae infection. However, antimicrobial resistance including multidrug resistance was observed to several commonly used antibiotics including penicillin. Hence, it is important to periodically monitor the antimicrobial resistance patterns to select empirical treatments for better management of pneumococcal infection.

The Research of IC Test Based on LTX-77 Test System

2014 ◽  
Vol 496-500 ◽  
pp. 1176-1179
Author(s):  
Li Tan ◽  
Yu Fang
Keyword(s):  
Test Object ◽  
Test System ◽  
Test Method ◽  
Test Results ◽  
Analog Ic ◽  
Test Platform ◽  
Logic Functions ◽  
Actual Test ◽  
Ic Test

LTX-77 test system is a large IC test system that is used for various kinds of analog IC, digital IC and analog digital mixed IC. It can be used to test DC parameters, AC parameters and logic functions. In the paper, the IC test platform is LTX-77 test system. IC ADC0804 was tested as the test object. The test method of IC is described in the view of actual test. The test results show that the test system is convenient and accurate, which has important practical value for IC manufacturers and users.

Inter-Bolt Variability of Cotton Duck #4 and the Effects on Cigarette Ignition Propensity Test Outcome

1995 ◽  
Vol 13 (2) ◽  
pp. 127-140 ◽  
Author(s):  
Richard Jupe ◽  
Donald K. Shipley ◽  
William Z. Hudson ◽  
Joseph T. Wanna ◽  
Linda C. Greear
Keyword(s):  
Test Methods ◽  
Physical Parameters ◽  
Test Results ◽  
Astm Method ◽  
Significant Difference ◽  
Ignition Propensity

Two bolts of cotton duck fabric that meet military specifications and the purchasing guidelines described by the National Institute of Standards and Technology (NIST) for use as a substrate in "Test Methods for Quantifying the Propensity of Cigarettes to Ignite Soft Furnishings" were tested with smoldering cigarettes to determine the effect of inter-bolt variations on cigarette ignition propensity test outcome. The test was designed around an ASTM method that calls for the control of all known test variables, except for those inherent to the fabric's manufacture. The ignitability of each fabric was determined by testing two sets of 48 replications for each of two experimental cigarettes. The two bolts of cotton duck fabric showed a statistically significant difference in ignitions, independent of environmental and experimental fac tors. Two additional bolts of cotton duck #4 were analyzed. Cigarette ignition test results and the physical parameters of the additional bolts offer evidence that the NIST specifications are difficult to meet and further that test results are extremely sensitive to fabric properties.

The Improved Friction Properties of Bonded MoS2 Films by MAO Treating of Al Substrate

2013 ◽  
Vol 275-277 ◽  
pp. 1911-1914 ◽  
Author(s):  
Han Jun Hu ◽  
Hui Zhou ◽  
Yu Gang Zheng ◽  
Kai Feng Zhang ◽  
Zhi Hua Wan
Keyword(s):  
Tribological Properties ◽  
Solid Lubricants ◽  
Ceramic Coatings ◽  
Test System ◽  
Test Method ◽  
Test Results ◽  
Specimen Test ◽  
Micro Arc Oxidation ◽  
A New Technique ◽  
Porous Microstructures

The bonded MoS2 films are widely used as solid lubricants in aerospace mechanisms due to their excellent tribological properties. Traditionally, the MoS2 was directly bonded on the Al substrate that was only treated by the technique named of sandblast. For improving the tribological properties of MoS2 films, micro arc oxidation (MAO) instead of sandblast was introduced as a new technique for treating of Al substrate. In this article, the tribological properties of MoS2 films which were bonded on different surface of Al substrate as mentioned above were discussed, respectively. It was concluded from the test results that the MoS2 films bonded on substrate treated by MAO have better tribological properties than those samples treated by sandblast. The endurance life against abrasion of the former is as high as twenty times of the latter by the stand test method of ball on disk using the UMT Multi-Specimen Test System. This test results could be illustrated by the following reasons. The first is the porous microstructures of MAO ceramic coatings on the Al substrate. The coatings have numerous pits to be good at increasing the binding force with the MoS2 films, and the pits can also provide a MoS2 lubricants reservoir during processes of friction. Both of them improved the MoS2 film’s ability of wear-protective. The second is that hardness of the coating is higher than the Al, and this ensures well wearing resistance, especially in practical application to big load-supporting moving parts, such as bearing, gear, etc…

Study on Conventional Domed Bursting Disc Material and Burst Pressure Test

2013 ◽  
Vol 690-693 ◽  
pp. 2371-2378
Author(s):  
Wei Pu Xu ◽  
Yi Ting Liu
Keyword(s):  
Stainless Steel ◽  
Tensile Test ◽  
316L Stainless Steel ◽  
Performance Test ◽  
Test Method ◽  
Burst Pressure ◽  
Test Results ◽  
Manufacturing Method ◽  
Pressure Test ◽  
Disc Material

A brief overview is given in the conventional domed bursting disc structure and manufacturing method. 316L stainless steel as a template is selected. With the investigation on bursting disc material tensile test method, the test results are summarized,also the burst results of disc burst pressure in different sizes. With the help of bursting disc material performance test and bursting disc burst pressure test of 316L , the test results provide a reference for other types of bursting disc.

Analysis Method for Impact and Dispersion Behavior of Water-Filled Tank

2018 ◽  
Vol 4 (4) ◽  
Author(s):  
Hidekazu Takazawa ◽  
Kazuma Hirosaka ◽  
Katsumasa Miyazaki ◽  
Norihide Tohyama ◽  
Naomi Matsumoto
Keyword(s):  
Structural Damage ◽  
Impact Test ◽  
Velocity Ratio ◽  
Research Centre ◽  
Dispersion Pattern ◽  
Test Results ◽  
Analysis Method ◽  
Cylindrical Tank ◽  
Dispersion Behavior ◽  
The Impact

A new Japanese nuclear regulation involves estimating the possible damage to plant structures due to intentional aircraft impact. The effect of aircraft impact needs to be considered in the existing nuclear power plants. The structural damage and fuel dispersion behavior after aircraft impact into plant structures can be evaluated using finite element analysis (FEA). FEA needs validated experimental data to determine the reliability of the results. In this study, an analysis method was validated using a simple model such as a cylindrical tank. Numerical simulations were conducted to evaluate the impact and dispersion behavior of a water-filled cylindrical tank. The simulated results were compared with the test results of the VTT Technical Research Centre of Finland (VTT). The simulations were carried out using a multipurpose FEA code LS-DYNA®. The cylindrical tank was modeled using a shell element, and the tank water was modeled using smoothed particle hydrodynamics (SPH) elements. First, two analysis models were used to evaluate the effect of the number of SPH elements. One had about 300,000 SPH elements and the other had 37,000 SPH elements. The cylindrical tank ruptured in the longitudinal direction after crashing into a rigid wall, and the filled water dispersed. There were few differences in the simulated results when using different numbers of SPH elements. The VTT impact test was simulated with an arbitrary Lagrangian-Eulerian (ALE) element to consider the air drag. The analytical dispersion pattern and history of dispersion velocity ratio agreed well with the impact test results.

scholarly journals Hedonic Test Method for Measuring Instant Pindang Seasoning Powder Preferences

2019 ◽  
Vol 3 (1) ◽  
pp. 34
Author(s):  
Dea Tio Mareta
Keyword(s):  
Test Method ◽  
Test Results ◽  
Drying Method ◽  
Typical Food ◽  
Hedonic Scale

Instant seasoning for cooking are commonly known by people who want something practical. Pindang is a typical food of Lampung and South Sumatra Province, consisting of various spices and herbs. Instant pindang seasoning powder made with foam mat drying method using 3 varations of foam additives. The purpose of this study was to determine the level of taste, aroma, and color of instant pindang seasoning powder made with three variations of foam additives, namely 5% (w/w), 10% (w/w), and 15% (w/w). The hedonic test for instant pindang seasoning powder were carried out on 35 panelists. Panelists were faced with 3 samples with 3 different sample numbers. Panelists were asked to assess how much preference for seasoning products using hedonic scale. The hedonic test results showed that, with the addition of 15% (w/w) foam is preferred in terms of color. As for aroma and taste, there were no significant differences between the three products. Keywords: foam mat drying , hedonic test, instant pindang seasoning powder, pindang

Sign in / Sign up

Export Citation Format

Share Document