Influence of the Slant Angle of 3D Bluff Bodies on Longitudinal Vortex Formation

2010 ◽  
Vol 132 (5) ◽  
Author(s):  
Patrick Gilliéron ◽  
Annie Leroy ◽  
Sandrine Aubrun ◽  
Pierre Audier
Keyword(s):  
Structure Formation ◽  
Static Pressure ◽  
Vortex Formation ◽  
Longitudinal Vortex ◽  
Bluff Bodies ◽  
Rear Window ◽  
Slant Angle ◽  
Pressure Distributions ◽  
Friction Line ◽  
Bursting Process

This paper presents the experimental results and analytical arguments concerning simplified geometries of the rear window and windscreen of automotive vehicles in order to contribute to a better understanding of the swirling structure formation and vortex bursting processes. Static pressure distributions and skin friction line visualizations on both sides of the edge where the swirling structure is generated on the rear window of an Ahmed body are presented for different slant angles. Results show the influence of the slant angle on the swirling structure formation and further show that the vortex bursting process can be promoted by small rear window angles. These results are then extrapolated with the help of analytical demonstrations to the windscreen configuration to demonstrate that large windscreen slopes would have the same disintegration effect.

Surface Static Pressures in an Inlet Vortex Flow Field

1985 ◽  
Vol 107 (2) ◽  
pp. 387-393 ◽  
Author(s):  
W. Liu ◽  
E. M. Greitzer ◽  
C. S. Tan
Keyword(s):  
Flow Field ◽  
Static Pressure ◽  
Velocity Ratio ◽  
Ground Plane ◽  
Vortex Formation ◽  
Three Dimensional ◽  
Static Pressure Distribution ◽  
Pressure Distributions ◽  
Parametric Data ◽  
Basic Ideas

An experimental investigation of the three-dimensional flow field associated with an inlet vortex is reported. The specific configuration investigated is an inlet, in proximity to a ground plane, in crosswind. Parametric data are presented to define the regimes of vortex formation in this configuration, as a function of inlet height to diameter ratio and inlet velocity ratio. The detailed static pressure distribution on the inlet is given for two quite different flow regimes, one with a strong inlet vortex and one with no inlet vortex. These new quantitative data are supplemented by flow visualization studies that allow an estimate to be made of the circulation around the inlet vortex. It is argued that the static pressure distributions in both cases can be clearly interpreted using the basic ideas of inlet vortex formation that were previously developed from (qualitative) water tunnel studies.

Mean velocity and static pressure distributions of a circular jet

AIAA Journal ◽  
1997 ◽  
Vol 35 ◽  
pp. 196-197
Author(s):  
M. T. Islam ◽  
M. A. T. Ali
Keyword(s):  
Static Pressure ◽  
Mean Velocity ◽  
Pressure Distributions

Experimental and Computational Analyses of Pressure Differentials in Flexible Ducts With Different Bent Angles

2007 ◽  
Author(s):  
Ray R. Taghavi ◽  
Wonjin Jin ◽  
Mario A. Medina
Keyword(s):  
Pressure Drop ◽  
Static Pressure ◽  
Complex Geometry ◽  
Analysis Data ◽  
Secondary Flows ◽  
Low Flow ◽  
Pressure Drops ◽  
Pressure Distributions ◽  
Geometrical Effects ◽  
Cfd Analyses

A set of experimental analyses was conducted to determine static pressure drops inside non-metallic flexible, spiral wire helix core ducts, with different bent angles. In addition, Computational Fluid Dynamics (CFD) solutions were performed and verified by comparing them to the experimental data. The CFD computations were carried out to produce more systematic pressure drop information through these complex-geometry ducts. The experimental setup was constructed according to ASHRAE Standard 120-1999. Five different bent angles (0, 30, 45, 60, and 90 degrees) were tested at relatively low flow rates (11 to 89 CFM). Also, two different bent radii and duct lengths were tested to study flexible duct geometrical effects on static pressure drops. FLUENT 6.2, using RANS based two equations - RNG k-ε model, was used for the CFD analyses. The experimental and CFD results showed that larger bent angles produced larger static pressure drops in the flexible ducts. CFD analysis data were found to be in relatively good agreement with the experimental results for all bent angle cases. However, the deviations became slightly larger at higher velocity regimes and at the longer test sections. Overall, static pressure drop for longer length cases were approximately 0.01in.H2O higher when compared to shorter cases because of the increase in resistance to the flow. Also, the CFD simulations captured more pronounced static pressure drops that were produced along the sharper turns. The stronger secondary flows, which resulted from higher and lower static pressure distributions in the outer and inner surfaces, respectively, contributed to these higher pressure drops.

Laminar Fluid Flow Around Two Wall-Mounted Blocks of Different Size

2009 ◽  
Author(s):  
Mohammad Mehdi Tavakol ◽  
Mohammad Eslami
Keyword(s):  
Fluid Flow ◽  
Free Stream ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Bluff Bodies ◽  
Wake Region ◽  
Science And Engineering ◽  
Vortical Structures ◽  
Laminar Fluid Flow ◽  
Pressure Distributions

Fluid flow around single or multiple bluff bodies mounted on a surface has great significance in science and engineering. Understanding the characteristics of different vortices formed around wall-mounted bodies is quite necessary for different applications. Although the case of a single surface mounted cube has been studied extensively, only little attention has been paid to the flow around two or more rectangular blocks in array. Therefore, a CFD code is developed to calculate three dimensional steady state laminar fluid flow around two cuboids of arbitrary size and configuration mounted on a surface in free stream conditions. The employed numerical scheme is finite volume and SIMPLE algorithm is used to treat pressure and velocity coupling. Results are presented for two rectangular blocks of the different size mounted on a surface in various inline arrangements. Streamlines are plotted for blocks of different size ratio. Velocity and pressure distributions are also plotted in the wake region behind the obstacles. It is shown that how the behavior of flow field and vortical structures depend on the respective size and location of the larger block in comparison with the case of two inline wall mounted cubes of the same size.

Three-dimensional flow in cavities

1963 ◽  
Vol 16 (4) ◽  
pp. 620-632 ◽  
Author(s):  
D. J. Maull ◽  
L. F. East
Keyword(s):  
Static Pressure ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Three Dimensional Flow ◽  
Large Span ◽  
Dimensional Flow ◽  
Pressure Distributions ◽  
Oil Flow ◽  
Two Dimensional Flow

The flow inside rectangular and other cavities in a wall has been investigated at low subsonic velocities using oil flow and surface static-pressure distributions. Evidence has been found of regular three-dimensional flows in cavities with large span-to-chord ratios which would normally be considered to have two-dimensional flow near their centre-lines. The dependence of the steadiness of the flow upon the cavity's span as well as its chord and depth has also been observed.

Aerodynamic Characteristics of Asymmetric Bluff Bodies

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
J. C. Hu ◽  
Y. Zhou
Keyword(s):  
Bluff Body ◽  
Laser Doppler Anemometry ◽  
Vortex Formation ◽  
Aerodynamic Characteristics ◽  
Bluff Bodies ◽  
Reynolds Stresses ◽  
Freestream Velocity ◽  
Drag And Lift ◽  
Particle Imaging ◽  
Visualization Techniques

The wake of asymmetric bluff bodies was experimentally measured using particle imaging velocimetry, laser Doppler anemometry, load cell, hotwire, and flow visualization techniques at Re=2600–8500 based on the freestream velocity and the characteristic height of the bluff bodies. Asymmetry is produced by rounding some corners of a square cylinder and leaving others unrounded. It is found that, with increasing corner radius, the flow reversal region is expanded, and the vortex formation length is prolonged. Accordingly, the vortex shedding frequency increases and the base pressure rises, resulting in a reduction in the mean drag as well as the fluctuating drag and lift. It is further found that, while the asymmetric cross section of the cylinder causes the wake centerline to shift toward the sharp corner side of the bluff body, the wake remains globally symmetric about the shifted centerline. The near wake of asymmetric bluff bodies is characterized in detail, including the Reynolds stresses, characteristic velocity, and length scale, and is further compared with that of the symmetric ones.

Heat Transfer in a Supersonic Parallel Diffuser

1965 ◽  
Vol 7 (1) ◽  
pp. 1-7 ◽  
Author(s):  
P. J. Baker
Keyword(s):  
Heat Transfer ◽  
Pressure Gradient ◽  
Cross Section ◽  
Static Pressure ◽  
Positive Pressure ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Pipe Flows ◽  
Pressure Distributions ◽  
The Mean

This paper presents the results of heat transfer measurements taken on a two-dimensional supersonic parallel diffuser. The wall static pressure distributions and the corresponding heat transfer coefficients and fluxes have been measured for a range of initial total pressures. The effects of varying the area of the diffuser cross-section for the same upstream generating nozzle have also been studied. Mach number profiles measured at sections along the diffuser show that in the presence of shock waves and a positive pressure gradient the flow is very much underdeveloped. In general, the mean level of heat transfer is found to be much greater than that predicted by conventional empirical equations for subsonic pipe flows with zero pressure gradient. Further, on comparison between normal and oblique shock diffusion the former is found to give the higher level of heat transfer.

An Investigation of the Forces on Three Dimensional Bluff Bodies in Rough Wall Turbulent Boundary Layers

1977 ◽  
Vol 99 (3) ◽  
pp. 503-509 ◽  
Author(s):  
B. E. Lee ◽  
B. F. Soliman
Keyword(s):  
Three Dimensional ◽  
The Body ◽  
Bluff Bodies ◽  
Drag Forces ◽  
Pressure Distributions ◽  
Mean Pressure ◽  
Flow Phenomena ◽  
The Mean ◽  
Building Ventilation ◽  
Group Density

A study has been made of the influence of grouping parameters on the mean pressure distributions experienced by three dimensional bluff bodies immersed in a turbulent boundary layer. The range of variable parameters has included group density, group pattern and incident flow type and direction for a simple cuboid element form. The three flow regimes associated with increasing group density are reflected in both the mean drag forces acting on the body and their associated pressure distributions. A comparison of both pressure distributions and velocity profile parameters with established work on two dimensional bodies shows close agreement in identifying these flow regime changes. It is considered that the application of these results may enhance our understanding of some common flow phenomena, including turbulent flow over rough surfaces, building ventilation studies and environmental wind around buildings.

scholarly journals Heat Transfer and Pressure Distributions on a Gas Turbine Blade Tip

2000 ◽  
Vol 122 (4) ◽  
pp. 717-724 ◽  
Author(s):  
Gm. S. Azad ◽  
Je-Chin Han ◽  
Shuye Teng ◽  
Robert J. Boyle
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Rotor Blade ◽  
Static Pressure ◽  
Pressure Distributions ◽  
Blade Tip

Heat transfer coefficient and static pressure distributions are experimentally investigated on a gas turbine blade tip in a five-bladed stationary linear cascade. The blade is a two-dimensional model of a first-stage gas turbine rotor blade with a blade tip profile of a GE-E3 aircraft gas turbine engine rotor blade. The flow condition in the test cascade corresponds to an overall pressure ratio of 1.32 and exit Reynolds number based on axial chord of 1.1×106. The middle 3-blade has a variable tip gap clearance. All measurements are made at three different tip gap clearances of about 1, 1.5, and 2.5 percent of the blade span. Heat transfer measurements are also made at two different turbulence intensity levels of 6.1 and 9.7 percent at the cascade inlet. Static pressure measurements are made in the midspan and the near-tip regions as well as on the shroud surface, opposite the blade tip surface. Detailed heat transfer coefficient distributions on the plane tip surface are measured using a transient liquid crystal technique. Results show various regions of high and low heat transfer coefficient on the tip surface. Tip clearance has a significant influence on local tip heat transfer coefficient distribution. Heat transfer coefficient also increases about 15–20 percent along the leakage flow path at higher turbulence intensity level of 9.7 over 6.1 percent. [S0889-504X(00)00404-9]

Flow Fields in a Two-Dimensional Diffuser With Extraction of Fluid on the Diverging Walls

1972 ◽  
Vol 94 (3) ◽  
pp. 226-232
Author(s):  
D. O. Rockwell
Keyword(s):  
Experimental Verification ◽  
Static Pressure ◽  
Flow Fields ◽  
Hydrogen Bubble ◽  
Two Dimensional ◽  
Stagnation Region ◽  
Pressure Distributions

A theory is developed to describe the inviscid core in two-dimensional unstalled diffusers with suction (extraction) on the diverging walls. Experimental wall static pressure distributions and streamline patterns agree well with those predicted theoretically. Under appropriate extraction conditions, a stagnation region is located downstream of the diverging wall extraction station. Experimental verification of the streamline patterns and of the location of this stagnation region was achieved via hydrogen bubble visualization. In addition, the possible stall conditions, which result if improper extraction is employed, are described qualitatively.

Sign in / Sign up

Export Citation Format

Share Document