Numerical Analysis of Convective Heat Transfer From an Elliptic Pin Fin Heat Sink With and Without Metal Foam Insert

2010 ◽  
Vol 132 (7) ◽  
Author(s):  
Hamid Reza Seyf ◽  
Mohammad Layeghi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Numerical Analysis ◽  
Pressure Drop ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Heat Sink ◽  
Metal Foam ◽  
Pin Fin

A numerical analysis of forced convective heat transfer from an elliptical pin fin heat sink with and without metal foam inserts is conducted using three-dimensional conjugate heat transfer model. The pin fin heat sink model consists of six elliptical pin rows with 3 mm major diameter, 2 mm minor diameter, and 20 mm height. The Darcy–Brinkman–Forchheimer and classical Navier–Stokes equations, together with corresponding energy equations are used in the numerical analysis of flow field and heat transfer in the heat sink with and without metal foam inserts, respectively. A finite volume code with point implicit Gauss–Seidel solver in conjunction with algebraic multigrid method is used to solve the governing equations. The code is validated by comparing the numerical results with available experimental results for a pin fin heat sink without porous metal foam insert. Different metallic foams with various porosities and permeabilities are used in the numerical analysis. The effects of air flow Reynolds number and metal foam porosity and permeability on the overall Nusselt number, pressure drop, and the efficiency of heat sink are investigated. The results indicate that structural properties of metal foam insert can significantly influence on both flow and heat transfer in a pin fin heat sink. The Nusselt number is shown to increase more than 400% in some cases with a decrease in porosity and an increase in Reynolds number. However, the pressure drop increases with decreasing permeability and increasing Reynolds number.

TURBULENT-FORCED CONVECTIVE HEAT TRANSFER AND PRESSURE DROP ANALYSIS OF FE3O4 MAGNETIC NANOFLUID IN A CIRCULAR MICROCHANNEL

2015 ◽  
Vol 75 (11) ◽  
Author(s):  
Nor Azwadi Che Sidik ◽  
M.M. Yassin ◽  
M.N. Musa
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Volume Concentration ◽  
Pure Water ◽  
Dimensional Structure ◽  
Outlet Section

A numerical simulation was accomplished in this study that investigated the turbulent force convective heat transfer and pressure drop in straight circular copper pipe with a hydraulic diameter of 0.0005m and 0.1m in length, as given by Lee and Mudawar [11]. The enhancement of heat transfer for water and nanofluids (Fe3O4) under 100 [W/m2] constant heat flux was applied around the wall of the pipe. In this study, standard k-ɛ turbulence model was employed and was performed at a steady state flow, incompressible turbulent flow, and three-dimensional structure. Various volume concentrations of nanoparticles were conducted in the range of 1% to 15% at constant nanoparticle diameter size, which was 32 nm. The heat transfer enhancement was obtained in the range of Reynolds number from 3000 to 10,000. The results displayed an increase in Reynolds number and volume concentrations, as well as an increase in the Nusselt number. The optimum Nusselt number gained was about 5% to 6% of volume concentration at each Reynolds number tested. Besides, with the increase of Reynolds number, the variation pressure saw a dropped for inlet, whereas an increase in the outlet section. Moreover, the  increase in volume concentration also caused a small increment in the pressure drop compared to pure water.

Numerical investigation on fluid flow and convective heat transfer in a microchannel heat sink with fan-shaped cavities and ribs

2021 ◽  
pp. 095440892098743
Author(s):  
K Bala Subrahmanyam ◽  
Pritam Das ◽  
Aparesh Datta
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Thermal Performance ◽  
Heat Sink ◽  
Heat Extraction ◽  
Microchannel Heat Sink

In the present study, a detailed numerical simulations of liquid flow in microchannel heat sink with four different geometry of ribs: rectangular (RR), backward triangular (BTR), forward triangular (FTR) and diamond (DR) arranged symmetrically inside reentrant fan shaped cavities (FC) on side walls has been conducted and compared with smooth channel (SC) to acquire fluid flow and heat transfer characteristics between Reynolds numbers of 136−588. The local pressure, temperature and heat transfer coefficients were determined to understand the convective heat transfer regimes and to analyze local flow behavior. The three-dimensional conjugate heat transfer model, investigation is done extensively to identify the influence of geometrical parameters towards augmenting thermal performance with parametric optimization. Evolved governing equations are solved by using SIMPLEC algorithm. Attempt has been made to improve heat extraction ability with reasonable pressure drop by replacing the existing simple design of microsink. It is observed that Nusselt number and friction factor are in good agreement with previous experimental data. Based on detailed parametric study, it was found that FC-RR is good in achieving maximum Nusselt number, but due to higher pressure drop penalty giving lower performance. Out of four proposed, FC-DR is conferring upstanding balance between heat transfer, pressure drop and giving the best thermal performance of 1.97 at Re = 391.47.

Enhancement of Heat Transfer of Rectangular Saw Tooth Shaped Micro Channel Heat Sink with Water Nano Fluid/Aluminium Oxide

2015 ◽  
Vol 813-814 ◽  
pp. 685-689
Author(s):  
M. Vijay Anand Marimuthu ◽  
B. Venkatraman ◽  
S. Kandhasamy
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Heat Sink ◽  
Micro Channel ◽  
Performance Curve ◽  
Theoretical Level ◽  
Enhancement Of Heat Transfer ◽  
Nano Fluid

This paper investigates the performance and characteristics of saw tooth shape micro channel in the theoretical level. If the conduct area of the nano fluid increases the heat transfer also increases. The performance curve has drawn Reynolds number against nusselt number, heat transfer co efficient. Pressure drop plays an important role in this device. If pressure drop is high the heat transfer increases. The result in this experiment shows clearly that the heat transfer is optimized.

Assessment of heat transfer and pressure drop of metal foam-pin-fin heat sink

2021 ◽  
Vol 170 ◽  
pp. 107109
Author(s):  
Mohanad A. Alfellag ◽  
Hamdi E. Ahmed ◽  
Mohammed Gh. Jehad ◽  
Marwan Hameed
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
Metal Foam ◽  
Pin Fin

Convective Heat Transfer Coefficient and Pressure Drop of Al2O3-Water Nanofluid in a Single-Phase Microchannel for Cooling of High Heat Output Devices

2008 ◽  
Author(s):  
Guillermo E. Valencia ◽  
Miguel A. Ramos ◽  
Antono J. Bula
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Convective Heat Transfer Coefficient ◽  
Heat Output ◽  
Flux Boundary Condition

The paper describes an experimental procedure performed to obtain the convective heat transfer coefficient of Al2O3 nanofluid working as cooling fluid under turbulent regimen through arrays of aluminum microchannel heat sink having a diameter of 1.2 mm. Experimental Nusselt number correlation as a function of the volume fractions, Reynolds, Peclet and Prandtl numbers for a constant heat flux boundary condition is presented. The correlation for Nusselt number has a good agreement with experimental data and can be used to predict heat transfer coefficient for this specific nanofluid, water/Al2O3. Furthermore, the pressure drop is also analyzed considering the different nanoparticles concentration.

scholarly journals Determination of Heat Transfer Coefficients Over Ribbed Surfaces With Infrared Thermography

1997 ◽  
Author(s):  
Francisco P. Brójo ◽  
Luís C. Gonçalves ◽  
Pedro D. Silva
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Convective Heat Transfer Coefficient ◽  
Stanton Number ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

The scope of the present work is to characterize the heat transfer between a ribbed surface and an air flow. The convective heat transfer coefficients, the Stanton number and the Nusselt number were calculated in the Reynolds number range, 5.13 × 105 to 1.02 × 106. The tests were performed inside a turbulent wind tunnel with one roughness height (e/Dh = 0.07). The ribs had triangular section with an attack angle of 60°. The surface temperatures were measured using an infrared (IR) thermographic equipment, which allows the measurement of the temperature with a good spatial definition (10.24 × 10−6 m2) and a resolution of 0.1°C. The experimental measures allowed the calculation of the convective heat transfer coefficient, the Stanton number and the Nusselt number. The results obtained suggested a flow pattern that includes both reattachment and recirculation. Low values of the dimensionless Stanton number, i.e. Stx*, are obtained at the recirculation zones and very high values of Stx* at the zones of reattachment. The reattachment is located at a dimensionless distance of 0.38 from the top of the rib. That distance seems to be independent of the Reynolds number. The local dimensionless Stanton number remains constant as the Reynolds number varies. The convective heat transfer coefficient presents an uncertainty in the range of 3 to 6%.

scholarly journals Effect of Pin Diameter Degressive Gradient on Heat Transfer in a Microreactor with Non-Uniform Pin-Fin Array under Low Reynolds Number Conditions

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2702
Author(s):  
Miao Qian ◽  
Jie Li ◽  
Zhong Xiang ◽  
Chao Yan ◽  
Xudong Hu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Pressure Drop ◽  
Friction Factor ◽  
Low Reynolds Number ◽  
Hydrodynamic Characteristics ◽  
Pin Fin ◽  
Low Reynolds ◽  
Pin Fin Array

To improve the efficiency of hydrogen-producing microreactors with non-uniform pin-fin array, the influence of the pin diameter degressive gradient of the non-uniform pin-fin array (NPFA) on heat transfer and pressure drop characteristics is analyzed in this study via numerical simulation under low Reynolds number conditions. Because correlations in prior studies cannot be used to predict the Nusselt number and pressure drop in the NPFA, new heat transfer and friction factor correlations are developed in this paper to account for the effect of the pin diameter degressive gradient, providing a method for the optimized design of the pin diameter degressive gradient for a microreactor with NPFA. The results show that the Nusselt number and friction factor under a low Reynolds number are quite sensitive to the pin diameter degressive gradient. Based on the new correlations, the exponents of the pin diameter degressive gradient for the friction factor and Nusselt number were 6.9 and 2.1, respectively, indicating the significant influence of the pin diameter degressive gradient on the thermal and hydrodynamic characteristics in the NPFA structure.

Unsteady Heat Transfer Around Low Aspect Ratio Cylinders in an Array

2016 ◽  
Author(s):  
Shawn Siroka ◽  
Melissa Shallcross ◽  
Stephen Lynch
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Aspect Ratio ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Convective Heat Flux ◽  
Pin Fin ◽  
Low Aspect Ratio ◽  
Minimum Heat

Cylindrical pins, often called pin fins, are used to create turbulence and promote convective heat transfer within many devices, ranging from computer heat sinks to the trailing edge of jet engine turbine blades. Previous experiments have measured the time-averaged heat transfer over a single pin as well as the flow fields around the pin. However, in this study, focus is placed on the instantaneous heat flux around the centerline of a low aspect-ratio pin within an array. Time-mean and unsteady convective heat flux are measured around the circumference of an isothermal heated test pin via a microsensor located at the surface. The pin is positioned at various locations within a staggered array in a large-scale wind tunnel. Reynolds numbers from 3,000 to 50,000, based on pin diameter and maximum velocity between pins, are tested with a streamwise spacing of 1.73 diameters between rows, a spanwise spacing of 2 diameters, and a pin height of 1 diameter. The time-averaged and standard deviation of convective heat flux around the pin is higher over most of the pin surface for pins in downstream row positions of an array relative to the first row pin, except in the wake which has similar levels for all rows. For a given pin position in the array, as the Reynolds number increases, the point of minimum heat transfer moves circumferentially upstream on the pin fin, corresponding to earlier transition of the pin boundary layer. Also, for a given Reynolds number, the minimum heat transfer point on the pin circumference moves upstream for pins further into the array, due to the high turbulence levels within the array which cause early transition. For a single pin row with no downstream pins, heat transfer fluctuations are very high on the backside of the pin due to the significant unsteadiness in the pin wake, but heat transfer fluctuations are suppressed for a pin with downstream rows due to the confining effects of the close spacing. The results from this study can be used to design pin-fin arrays that take advantage of unsteadiness and increase overall convective heat transfer for various industry components.

Effect of Reynolds Number, Hole Patterns and Hole Inclination on Cooling Performance of an Impinging Jet Array: Part I — Convective Heat Transfer Results and Optimization

2016 ◽  
Author(s):  
Weihong Li ◽  
Xueying Li ◽  
Jing Ren ◽  
Hongde Jiang ◽  
Li Yang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Impinging Jet ◽  
Target Plate ◽  
New Correlation

This study comprehensively illustrates the effect of Reynolds number, hole spacing, jet-to-target distance and hole inclination on the convective heat transfer performance of an impinging jet array. Highly resolved heat transfer coefficient distributions on the target plate are obtained utilizing transient liquid crystal over a range of Reynolds numbers varying between 5,000 and 25,000. Effect of streamwise and spanwise jet-to-jet spacing (X/D, Y/D: 4–8) and jet-to-target plate distance (Z/D: 0.75–3) are employed composing a test matrix of 36 different geometries. Additionally, the effect of hole inclination (θ: 0°–40°) on the heat transfer coefficient is investigated. Optical hole spacing arrangements and impingement distance are pointed out to maximize the area-averaged Nusselt number and minimize the amount of cooling air. Also included is a new correlation, based on that of Florschuetz et al., to predict row-averaged Nusselt number. The new correlation is capable to cover low Z/D∼0.75 and presents better prediction of row-averaged Nusselt number, which proves to be an effective impingement design tool.

Sign in / Sign up

Export Citation Format

Share Document