Comparison of Neutron and Synchrotron Diffraction Measurements of Residual Stress in Bead-on-Plate Weldments

2010 ◽  
Vol 132 (1) ◽  
Author(s):  
Anna M. Paradowska ◽  
John W. H. Price ◽  
Trevor R. Finlayson ◽  
Ulrich Lienert ◽  
Raafat Ibrahim
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Residual Strain ◽  
Development Process ◽  
Synchrotron Diffraction ◽  
Stress Relieving ◽  
Before And After ◽  
Strain Stress ◽  
Good Agreement

This paper explores the use of neutron and synchrotron diffractions for the evaluation of residual stresses in welded components. It has been shown that it is possible to achieve very good agreement between the two independent diffraction techniques. This study shows the significance of the weld start and end sites on the residual strain/stress distribution. Quantitative evaluation of the residual stress development process for multibead weldments has been presented. Some measurements were also taken before and after postweld stress relieving to establish the reduction and redistribution of the residual stress. The detailed measurements of residual stress around the weld achieved in this work significantly improve the knowledge and understanding of residual stress in welded components.

Neutron and Synchrotron Diffraction Measurements of Residual Stress in Steel Weldments

2007 ◽  
Author(s):  
Anna M. Paradowska ◽  
John W. H. Price ◽  
Raafat Ibrahim
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Stress Distribution ◽  
State Of The Art ◽  
Mechanical Tests ◽  
Post Weld Heat Treatment ◽  
Synchrotron Diffraction ◽  
Before And After ◽  
Strain Stress ◽  
Weld Heat

This paper explores the use of state-of-the-art instruments such as neutron and synchrotron diffraction for evaluation of residual stress in carbon steel welded components. The study shows significant variation in transverse residual strain/stress distribution across the length of the weld. Measurements before and after post weld heat treatment are reported together with traditional mechanical tests. The changes in residual stress distribution as weld beads are added in multi-bead welds are also presented. Important practical results are: i) The start and end of the weld are the most critical parts of the weldment. Implementations of run-in and run-out (which are subsequently ground off) can minimize the residual stress at the start and end of the weld. ii) Manipulation of the sequence especially around the weld toes can minimize the value of the residual stress in that region. iii) Post weld heat treatment is very effective at reducing residual stresses.

Neutron Diffraction Studies of Residual Stress Distribution in the Vicinity of the Single Pass Fillet Steel Welds

2015 ◽  
Vol 732 ◽  
pp. 13-19
Author(s):  
Ľuboš Mráz ◽  
Leif Karlsson ◽  
Miroslav Vrána ◽  
Pavol Mikula
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Neutron Diffraction ◽  
Residual Strain ◽  
Residual Stress Distribution ◽  
Filler Materials ◽  
Single Pass ◽  
Stress Measurements ◽  
Strain Stress ◽  
Steel Welds

In this contribution the results of residual strain/stress measurements performed on several single pass fillet steel welds which were carried out at different welding conditions, namely, with different filler materials are presented.

Magnetic Barkhausen Measurements for Determining Residual Stress Distribution in Welded Electrical Steels

2016 ◽  
Vol 856 ◽  
pp. 147-152 ◽  
Author(s):  
Polykseni Vourna ◽  
Aphrodite Ktena ◽  
Athanasios G. Mamalis ◽  
Evangelos Hristoforou ◽  
Peng Wan Chen ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Electron Beam Welding ◽  
Research Work ◽  
Calibration Procedure ◽  
Residual Stress Distribution ◽  
X Ray Diffraction ◽  
Electrical Steels ◽  
Good Agreement

In the present research work the determination of residual stress distribution in welded non-oriented electrical steel samples is discussed. Tungsten Inert Gas and Electron Beam Welding were used as the welding methods. The residual stresses induced by welding estimated by the magnetic, non-destructive method of Barkhausen noise and were compared with the values resulting from the semi-destructive method of X-ray diffraction Bragg-Brentano (XRD-BB). In order to evaluate accuracy and reliability of the magnetic methods applied, the steel samples were subjected in both compressive and tensile stress and the magnetic noise values were correlated to residual stress values through an appropriate calibration curve. Furthermore, the fluctuations of the residual stresses in the welding zones of the welded samples were discussed on the basis of the experimental evidence and the microstructural changes occurring during welding. It was found that the residual stress determined by MBN method was in good agreement with the XRD-BB results. However, the residual stress determined by magnetic permeability method was not in good agreement with the XRD-BB results. In contrast to the XRD-BB method, the magnetic techniques required a precise calibration procedure in all zones with noticeably different microstructure.

scholarly journals Analysis of Residual Stress in Stress Harps of Grey Iron by Experiment and Simulation

2014 ◽  
Vol 996 ◽  
pp. 586-591 ◽  
Author(s):  
Pål Schmidt ◽  
Lin Peng Ru ◽  
Vadim Davydov ◽  
Mattias Lundberg ◽  
Maqsood Ahmad ◽  
...  
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Casting Process ◽  
Axial Direction ◽  
Hole Drilling ◽  
Fe Simulations ◽  
Stress Relieving ◽  
Compressive Residual Stresses ◽  
Good Agreement ◽  
Grey Iron

Stress harps with bars of different size were used to study residual stresses due to different cooling rate during casting of a grey iron. Finite element (FE) simulations were performed to predict residual stresses from the casting process and the effect of a stress relieving heat treatment. Intended for validating the simulations, neutron diffraction (ND) and hole drilling methods were used to measure the residual stress distribution through the thickness and in a thin surface layer, respectively. Good agreement between the FE simulations and ND measurements is observed for the annealed harp and the normal and transverse directions of the as cast harp. Discrepancy occurs in the axial direction and especially in the side bars of the as cast harp for which the simulation shows much higher compressive residual stresses. The observed difference between the different techniques was discussed with respect to the characteristics of the different methods.

scholarly journals Modification of Residual Stresses in Laser Additive Manufactured AlSi10Mg Specimens Using an Ultrasonic Peening Technique

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 455 ◽  
Author(s):  
Xiaodong Xing ◽  
Xiaoming Duan ◽  
Xiaojing Sun ◽  
Haijun Gong ◽  
Liquan Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Finite Element Simulation ◽  
Residual Stress Distribution ◽  
Ultrasonic Peening ◽  
Element Simulation ◽  
Before And After

Ultrasonic peening treatment (UPT) has been proved to be an effective way of improving residual stresses distribution in weld structures. Thus, it shows a great potential in stress modification for metal parts fabricated by additive manufacturing technology. In this paper, an investigation into the ultrasonic treatment process of AlSi10Mg specimens fabricated by selective laser melting (SLM) process was conducted by means of experimental and numerical simulation. The specimens were prepared using a SLM machine, and UPT on their top surface was carried out. The residual stresses were measured with an X-ray stress diffraction device before and after UPT. Meanwhile, a finite element simulation method for analyzing the influence of UPT on the residual stress field of specimens was proposed and validated by experiments. Firstly, the thermal mechanical coupling numerical simulation of the SLM process of the specimen was carried out in order to obtain the residual stress distribution in the as-fabricated specimen. Then, the transient dynamic finite element simulation model of the UPT process of the specimen was established, and the UPT effect analysis was implemented. In the UPT simulation, the residual stress was applied as a pre-stress on the specimen, and the specimen’s material mechanical property was described by the Johnson–Cook model, whose parameters were determined by Split Hopkinson Pressure Bar (SHPB) experiment. The residual stress distribution before and after UPT predicted by the finite element model agree well with the measurement results. This paper concludes with a discussion of the effects of ultrasonic peening time, as well as the frequency and amplitude of the peening needle on residual stress.

Analysis on Residual Stresses of the Casing Part in Aeroengine Based on Hole-Drilling Method

2013 ◽  
Vol 770 ◽  
pp. 159-163
Author(s):  
Dian Ye Cao ◽  
Yin Fei Yang ◽  
Zhi Wu Liu ◽  
Jie Yu ◽  
Liang Li
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Annealing Treatment ◽  
Residual Stress Distribution ◽  
Hole Drilling ◽  
Hole Drilling Method ◽  
Measurement Results ◽  
Drilling Method ◽  
Before And After

In order to study the residual stress distribution of the casing part in aeroengine, the hole-drilling method was used to measure the residual stress before and after the annealing treatment. The measurement results indicated that the annealing treatment significantly improved the residual stress distribution in the part, and the residual stresses were showed as compressive stress. Meanwhile, the measured residual stress distribution would provide the basis for controlling the machining distortion of the casing part in aeroengine.

Theoretical prediction of residual stresses induced by cold spray with experimental validation

2019 ◽  
Vol 15 (3) ◽  
pp. 599-616 ◽  
Author(s):  
Dibakor Boruah ◽  
Xiang Zhang ◽  
Matthew Doré
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Cold Spray ◽  
Residual Stress Distribution ◽  
Thermal Mismatch ◽  
Individual Layer ◽  
Content Type ◽  
Layer Height ◽  
Proposed Model

PurposeThe purpose of this paper is to develop a simple analytical model for predicting the through-thickness distribution of residual stresses in a cold spray (CS) deposit-substrate assembly.Design/methodology/approachLayer-by-layer build-up of residual stresses induced by both the peening dominant and thermal mismatch dominant CS processes, taking into account the force and moment equilibrium requirements. The proposed model has been validated with the neutron diffraction measurements, taken from the published literature for different combinations of deposit-substrate assemblies comprising Cu, Mg, Ti, Al and Al alloys.FindingsThrough a parametric study, the influence of geometrical variables (number of layers, substrate height and individual layer height) on the through-thickness residual stress distribution and magnitude are elucidated. Both the number of deposited layers and substrate height affect residual stress magnitude, whereas the individual layer height has little effect. A good agreement has been achieved between the experimentally measured stress distributions and predictions by the proposed model.Originality/valueThe proposed model provides a more thorough explanation of residual stress development mechanisms by the CS process along with mathematical representation. Comparing to existing analytical and finite element methods, it provides a quicker estimation of the residual stress distribution and magnitude. This paper provides comparisons and contrast of the two different residual stress mechanisms: the peening dominant and the thermal mismatch dominant. The proposed model allows parametric studies of geometric variables, and can potentially contribute to CS process optimisation aiming at residual stress control.

A Further Study of Residual Stresses in Circumferential Welds

1973 ◽  
Vol 95 (4) ◽  
pp. 238-242 ◽  
Author(s):  
S. Vaidyanathan ◽  
H. Weiss ◽  
I. Finnie
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Base Metal ◽  
Filler Metal ◽  
Residual Stress Distribution ◽  
Experimental Results ◽  
Circumferential Welds ◽  
Single Pass ◽  
Full Penetration

The residual stress distribution for a circumferential weld between cylinders was obtained in a prior publication for a full penetration, single pass weld with no variation of alloy content across the weld. In the present work the approach is extended to cover a wider variety of weld conditions. It is shown that the effects of multipass welds, partial penetration welds, and welds with filler metal differing greatly in properties from the base metal can approximately be taken into account. Experimental results are presented to support the proposed method of analysis.

Residual Stresses in Steel and Zirconium Weldments

1997 ◽  
Vol 119 (2) ◽  
pp. 137-141 ◽  
Author(s):  
J. H. Root ◽  
C. E. Coleman ◽  
J. W. Bowden ◽  
M. Hayashi
Keyword(s):  
Residual Stress ◽  
Electron Beam ◽  
Neutron Diffraction ◽  
Residual Stresses ◽  
Prolonged Exposure ◽  
Electron Beam Welding ◽  
Three Dimensional ◽  
Diffraction Method ◽  
Outer Diameter ◽  
Stress Relieving

Three-dimensional scans of residual stress within intact weldments provide insight into the consequences of various welding techniques and stress-relieving procedures. The neutron diffraction method for nondestructive evaluation of residual stresses has been applied to a circumferential weld in a ferritic steel pipe of outer diameter 114 mm and thickness 8.6 mm. The maximum tensile stresses, 250 MPa in the hoop direction, are found at mid-thickness of the fusion zone. The residual stresses approach zero within 20 mm from the weld center. The residual stresses caused by welding zirconium alloy components are partially to blame for failures due to delayed hydride cracking. Neutron diffraction measurements in a GTA-welded Zr-2.5Nb plate have shown that heat treatment at 530°C for 1 h reduces the longitudinal residual strain by 60 percent. Neutron diffraction has also been used to scan the residual stresses near circumferential electron beam welds in irradiated and unirradiated Zr-2.5Nb pressure tubes. The residual stresses due to electron beam welding appear to be lower than 130 MPa, even in the as-welded state. No significant changes occur in the residual stress pattern of the electron-beam welded tube, during a prolonged exposure to thermal neutrons and the temperatures typical of an operating nuclear reactor.

scholarly journals Separation of the Formation Mechanisms of Residual Stresses in LPBF 316L

Metals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1234
Author(s):  
Alexander Ulbricht ◽  
Simon J. Altenburg ◽  
Maximilian Sprengel ◽  
Konstantin Sommer ◽  
Gunther Mohr ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Residual Stress Distribution ◽  
Formation Mechanisms ◽  
Micro Computed Tomography ◽  
Solidification Shrinkage ◽  
Stainless Steel 316L ◽  
Heat Accumulation ◽  
Cooling Rates

Rapid cooling rates and steep temperature gradients are characteristic of additively manufactured parts and important factors for the residual stress formation. This study examined the influence of heat accumulation on the distribution of residual stress in two prisms produced by Laser Powder Bed Fusion (LPBF) of austenitic stainless steel 316L. The layers of the prisms were exposed using two different border fill scan strategies: one scanned from the centre to the perimeter and the other from the perimeter to the centre. The goal was to reveal the effect of different heat inputs on samples featuring the same solidification shrinkage. Residual stress was characterised in one plane perpendicular to the building direction at the mid height using Neutron and Lab X-ray diffraction. Thermography data obtained during the build process were analysed in order to correlate the cooling rates and apparent surface temperatures with the residual stress results. Optical microscopy and micro computed tomography were used to correlate defect populations with the residual stress distribution. The two scanning strategies led to residual stress distributions that were typical for additively manufactured components: compressive stresses in the bulk and tensile stresses at the surface. However, due to the different heat accumulation, the maximum residual stress levels differed. We concluded that solidification shrinkage plays a major role in determining the shape of the residual stress distribution, while the temperature gradient mechanism appears to determine the magnitude of peak residual stresses.

Sign in / Sign up

Export Citation Format

Share Document