Comparative Performance, Emission, and Combustion Characteristics of Rice-Bran Oil and Its Biodiesel in a Transportation Diesel Engine

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
Avinash Kumar Agarwal ◽  
Atul Dhar
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Rice Bran ◽  
Heat Release Rate ◽  
Release Rate ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Pressure Rise ◽  
Combustion Characteristics ◽  
Comparative Performance

The methyl esters of vegetable oils known as biodiesel are becoming increasingly popular because of their low environmental impact and potential as a green alternative fuel for diesel engines. Methyl ester of rice-bran oil (RBOME) is prepared through the process of transesterification. In the present investigation, experiments have been carried out to examine the performance, emission, and combustion characteristics of a direct-injection transportation diesel engine running with diesel, 20% blend of rice-bran oil (RBO), and 20% blend of RBOME with mineral diesel. A four-stroke, four-cylinder, direct-injection transportation diesel engine (MDI 3000) was instrumented for the measurement of the engine performance, emissions, in-cylinder pressure-crank angle history, rate of pressure rise, and other important combustion parameters such as instantaneous heat release rate, cumulative heat release rate, mass fraction burned, etc. A careful analysis of the performance, emissions, combustion, and heat release parameters has been carried out. HC, CO, and smoke emissions for RBO and RBOME blends were lower than mineral diesel while NOx emissions were almost similar and brake specific fuel consumption (BSFC) was slightly higher than mineral diesel. Combustion characteristics were quite similar for the three fuels.

Combustion Characteristics of Rice Bran Oil Derived Biodiesel in a Transportation Diesel Engine

2006 ◽  
Author(s):  
Shailendra Sinha ◽  
Avinash Kumar Agarwal
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Rice Bran ◽  
Heat Release Rate ◽  
Release Rate ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Pressure Rise ◽  
Combustion Characteristics ◽  
Experimental Investigations

The methyl esters of vegetable oils, known as biodiesel are becoming increasingly popular because of their low environmental impact and potential as a green alternative fuel for diesel engines. They do not require significant modification in existing engine hardware. Methyl ester of rice bran oil (ROME) is prepared through the process of transesterification. Previous research has shown that ROME has comparable performance, lower bsfc in comparison to diesel. There was reduction in the emissions of CO, HC, and smoke but NOx emissions increased. In the present research, experimental investigations have been carried out to examine the combustion characteristics of a direct injection transportation diesel engine running with diesel, and 20% blend of ROME with diesel. A four-stroke, four-cylinder, direct-injection transportation diesel engine (MDI 3000) was fully instrumented for the measurement of combustion pressure, rate of pressure rise and other combustion parameters such as instantaneous heat release rate, cumulative heat release rate, mass fraction burned etc. Tests were performed at different loads ranging from no load to 100%, at constant engine speed. No engine hardware modification was carried out for the present study. A careful analysis of combustion and heat release parameters has been carried out, which gives precise information about the in-cylinder combustion of rice bran oil based biodiesel vis-a`-vis mineral diesel.

Combustion Characteristics of Single Cylinder Diesel Engine Fueled with Blends of Thumba Biodiesel as an Alternative Fuel

2019 ◽  
Vol 969 ◽  
pp. 451-460
Author(s):  
Manpreet Singh ◽  
Mohd Yunus Sheikh ◽  
Dharmendra Singh ◽  
P. Nageswara Rao
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Diesel Fuel ◽  
Release Rate ◽  
Mass Fraction ◽  
Pressure Rise ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Edible Vegetable Oil

The rapid rise in energy requirement and problem regarding atmosphere pollutions, renewable biofuels are the better alternative choice for the internal combustion engine to partially or totally replace the pollutant petroleum fuel. In the present work, thumba (Citrullus colocynthis) non-edible vegetable oil is used for the production of biodiesel and examine its possibility as diesel engine fuel. Transesterification process is used to produce biodiesel from thumba non-edible vegetable oil. Thumba biodiesel (TBD) is used to prepare five different volume concentration (blends) with neat diesel (D100), such as TBD5, TBD15, TBD25, TBD35 and TBD45 to run a single cylinder diesel engine. The diesel engine's combustion parameter such as in-cylinder pressure, rate of pressure rise, net heat release rate, cumulative heat release, mean gas temperature, and mass fraction burnt analyzed through graphs and compared all thumba biodiesel blends result with neat diesel fuel. The mass fraction burnt start earlier for thumba biodiesel blends compared to diesel fuel because of less ignition delay while peak in-cylinder pressure, maximum rate of pressure rise, maximum net heat release rate, maximum cumulative heat release, and maximum mean gas temperature has found decreased results up to 1.93%, 5.53%, 4.11%, 4.65%, and 1.73% respectively for thumba biodiesel.

Experimental investigation of the combustion characteristics of a biodiesel (rice-bran oil methyl ester)-fuelled direct-injection transportation diesel engine

2007 ◽  
Vol 221 (8) ◽  
pp. 921-932 ◽  
Author(s):  
S Sinha ◽  
A K Agarwal
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Vegetable Oils ◽  
Rice Bran ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Pressure Rise ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Crank Angle

Increased environmental awareness and depletion of fossil petroleum resources are driving industry to develop alternative fuels that are environmentally more acceptable. Transesterified vegetable oil derivatives called ‘biodiesel’ appear to be the most convenient way of utilizing bio-origin vegetable oils as substitute fuels in diesel engines. The methyl esters of vegetable oils do not require significant modification of existing engine hardware. Previous research has shown that biodiesel has comparable performance and lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC), and smoke but slightly increased NO x emissions. In the present experimental research work, methyl ester of rice-bran oil is derived through transesterification of rice-bran oil using methanol in the presence of sodium hydroxide (NaOH) catalyst. Experimental investigations have been carried out to examine the combustion characteristics in a direct injection transportation diesel engine running with diesel, biodiesel (rice-bran oil methyl ester), and its blends with diesel. Engine tests were performed at different engine loads ranging from no load to rated (100 per cent) load at two different engine speeds (1400 and 1800 r/min). A careful analysis of the cylinder pressure rise, heat release, and other combustion parameters such as the cylinder peak combustion pressure, rate of pressure rise, crank angle at which peak pressure occurs, rate of pressure rise, and mass burning rates was carried out. All test fuels exhibited similar combustion stages as diesel; however, biodiesel blends showed an earlier start of combustion and lower heat release during premixed combustion phase at all engine load-speed combinations. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend and, at higher engine loads, the crank angle position of the peak cylinder pressure for biodiesel blends shifted away from the top dead centre in comparison with baseline diesel data. The maximum rate of pressure rise was found to be higher for diesel at higher engine loads; however, combustion duration was higher for biodiesel blends.

Determination of the Start and End of Combustion in a Direct Injection Diesel Engine Using the Apparent Heat Release Rate

2017 ◽  
Author(s):  
Joseph Gerard T. Reyes ◽  
Edwin N. Quiros
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Injection Timing ◽  
Fuel Injector ◽  
Direct Injection Diesel Engine ◽  
Crank Angle ◽  
Start Of Combustion

The combustion duration in an internal combustion engine is the period bounded by the engine crank angles known as the start of combustion (SOC) and end of combustion (EOC), respectively. This period is essential in analysis of combustion for the such as the production of exhaust emissions. For compression-ignition engines, such as diesel engines, several approaches were developed in order to approximate the crank angle for the start of combustion. These approaches utilized the curves of measured in-cylinder pressures and determining by inspection the crank angle where the slope is steep following a minimum value, indicating that combustion has begun. These pressure data may also be utilized together with the corresponding cylinder volumes to generate the apparent heat release rate (AHRR), which shows the trend of heat transfer of the gases enclosed in the engine cylinder. The start of combustion is then determined at the point where the value of the AHRR is minimum and followed by a rapid increase in value, whereas the EOC is at the crank angle where the AHRR attains a flat slope prior to the exhaust stroke of the engine. To verify the location of the SOC, injection line pressures and fuel injection timing are also used. This method was applied in an engine test bench using a four-cylinder common-rail direct injection diesel engine with a pressure transducer installed in the first cylinder. Injector line pressures and fuel injector voltage signals per engine cycle were also recorded and plotted. By analyzing the trends of this curves in line with the generated AHRR curves, the SOC may be readily determined.

scholarly journals Performance, Emission and Combustion Characteristics of VCR CRDI Diesel Engine Fuelled with n-butanol Blends

2019 ◽  
Vol 16 (3) ◽  
pp. 6825-6843
Author(s):  
P. T. Selvan ◽  
G. S. Goteti
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Research Work ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Exhaust Emission ◽  
Performance Study

This research work indicates the analysis conducted to investigate the performance, exhaust emission and combustion characteristics of a VCR diesel engine fuelled with nbutanol blends at a rated speed of 1500 rpm with 300 bar injection pressure at compression ratios of 16, 18 and 20. The test fuel was prepared by adding n-butanol 10% (NB10) and 20% (NB20) to diesel by volume. The combustion characteristics investigated were; rise in-cylinder pressures, net heat release rate, cumulative heat release rate and mass fraction of fuel burned at all loads using three compression ratios. The emission and performance study also conducted. The higher heat release rates, increased cylinder pressures were observed for both the blends compared to diesel. Increased brake thermal efficiency observed at higher compression ratio for NB20 blend. It had also been observed that the emissions of CO2, HC and NOx were increased for both the blends, while CO emissions decreased in trend with an increase in compression ratio and blend strength.

scholarly journals Effect of Various Supercharger Boost Pressure to in-Cylinder Pressure and Heat Release Rate Characteristics of Direct Injection Diesel Engine at Various Engine Rotation

2019 ◽  
Vol 130 ◽  
pp. 01036
Author(s):  
Willyanto Anggono ◽  
Wataru Ikoma ◽  
Haoyu Chen ◽  
Zhiyuan Liu ◽  
Mitsuhisa Ichiyanagi ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Power Efficiency ◽  
Direct Injection ◽  
Boost Pressure ◽  
Cylinder Pressure ◽  
Stroke Length ◽  
Direct Injection Diesel Engine

The diesel engines are superior in terms of power efficiency and fuel economy compared to gasoline engines. In order to optimize the performance of direct injection diesel engine, the effect of various intake pressure (boost pressure) from supercharging direct injection diesel engine was studied at various engine rotation. A single cylinder direct injection diesel engine was used in this experiment. The bore diameter of the engine used was set to 85 mm, the stroke length was set to 96.9 mm, and the compression ratio was set to 16.3. The variation of engine rotation started from 800 rpm to 2 000 rpm with 400 rpm increment. The variation of boost pressure is bounded from 0 kPa boost pressure (naturally aspirated) to the maximum of 60 kPa boost pressure with 20 kPa boost pressure increment. The performance of the engine is evaluated in terms of in-cylinder pressure and heat release rate as the most important performance characteristics of the diesel engine. The in-cylinder pressure and heat release rate of direct injection diesel engine are increased with the elevation of boost pressure at various engine rotation. The raise of engine rotation resulted in the decrease of maximum in-cylinder pressure and heat release rate.

scholarly journals Combustion and emission characteristics of diesel engine fuelled with rice bran oil methyl ester and its diesel blends

2008 ◽  
Vol 12 (1) ◽  
pp. 139-150 ◽  
Author(s):  
Rao Gattamaneni ◽  
Saravanan Subramani ◽  
Sampath Santhanam ◽  
Rajagopal Kuderu
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Heat Release ◽  
Vegetable Oils ◽  
Rice Bran ◽  
Ignition Delay ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Engine Fuel ◽  
Maximum Heat

There has been a worldwide interest in searching for alternatives to petroleum-derived fuels due to their depletion as well as due to the concern for the environment. Vegetable oils have capability to solve this problem because they are renewable and lead to reduction in environmental pollution. The direct use of vegetable oils as a diesel engine fuel is possible but not preferable because of their extremely higher viscosity, strong tendency to polymerize and bad cold start properties. On the other hand, Biodiesels, which are derived from vegetable oils, have been recently recognized as a potential alternative to diesel oil. This study deals with the analysis of rice bran oil methyl ester (RBME) as a diesel fuel. RBME is derived through the transesterification process, in which the rice bran oil reacts with methanol in the presence of KOH. The properties of RBME thus obtained are comparable with ASTM biodiesel standards. Tests are conducted on a 4.4 kW, single-cylinder, naturally aspirated, direct-injection air-cooled stationary diesel engine to evaluate the feasibility of RBME and its diesel blends as alternate fuels. The ignition delay and peak heat release for RBME and its diesel blends are found to be lower than that of diesel and the ignition delay decreases with increase in RBME in the blend. Maximum heat release is found to occur earlier for RBME and its diesel blends than diesel. As the amount of RBME in the blend increases the HC, CO, and soot concentrations in the exhaust decreased when compared to mineral diesel. The NOx emissions of the RBME and its diesel blends are noted to be slightly higher than that of diesel.

Effects of λ on the Combustion Characteristics of HCCI Engine Fueled with N-Butanol

2015 ◽  
Vol 1092-1093 ◽  
pp. 508-511
Author(s):  
Jia Wang Zhou ◽  
Chun Hua Zhang ◽  
Gang Li ◽  
Ye Chun Shen
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Combustion Engine ◽  
Pressure Rise ◽  
Combustion Characteristics ◽  
Cylinder Pressure ◽  
Maximum Heat ◽  
Hcci Engine ◽  
Combustion Duration

The combustion characteristics of an HCCI engine fueled with n-butanol were investigated on a modified two-cylinder, four stoke diesel engine. The experiments were conducted on the HCCI engine with λ of 2.0, 2.5 and 3.0, and the intake air temperature and engine speed were kept at 140 °C and 1000rpm, respectively. Effects of λ on combustion characteristics including in-cylinder pressure rise rate, heat release rate, CA05 and combustion duration of HCCI combustion engine are discussed in details based on the recorded in-cylinder pressure. The results indicate that in-cylinder pressure and the rate of pressure rise both decrease with the increase of λ, the maximum heat release rate also decreases with the increase of λ but occurs at late crank angles. In addition, as λ increases, the combustion phasing retards and combustion duration becomes longer.

Sign in / Sign up

Export Citation Format

Share Document