Temperature Distribution in Cocurrent Two-Phase (Liquid-Liquid) Laminar Flow on Inclined Surfaces

1964 ◽  
Vol 86 (4) ◽  
pp. 476-480 ◽  
Author(s):  
M. Bentwich ◽  
S. Sideman
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Transverse Section ◽  
Heat Transfer Mechanism ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Inclined Surfaces ◽  
Steady State Temperature ◽  
Phase Liquid

The steady-state temperature distribution in stratified two-phase, laminar viscous flow down an inclined solid plane is analyzed. With the plane and atmosphere kept at constant uniform temperatures, the temperature distribution is evaluated for various heat-transfer coefficients at the exposed surface. Graetz’s general approach is adopted here so that this solution holds for arbitrary given temperatures at a transverse section upstream. This method is modified here so as to account for the discontinuities of the physical properties at the interface. This analysis thus yields a detailed account of the heat-transfer mechanism which takes place at the interface.

Forced Convective Boiling of Refrigerant HCFC123 in a Mini-Tube

2010 ◽  
Author(s):  
Koichi Araga ◽  
Keisuke Okamoto ◽  
Keiji Murata
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Mass Flux ◽  
Pool Boiling ◽  
Constant Heat Flux ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Convective Boiling ◽  
Frictional Pressure Drop ◽  
Heat Transfer Coefficients

This paper presents an experimental investigation of the forced convective boiling of refrigerant HCFC123 in a mini-tube. The inner diameters of the test tubes, D, were 0.51 mm and 0.30 mm. First, two-phase frictional pressure drops were measured under adiabatic conditions and compared with the correlations for conventional tubes. The frictional pressure drop data were lower than the correlation for conventional tubes. However, the data were qualitatively in accord with those for conventional tubes and were correlated in the form φL2−1/Xtt. Next, heat transfer coefficients were measured under the conditions of constant heat flux and compared with those for conventional tubes and for pool boiling. The heat transfer characteristics for mini-tubes were different from those for conventional tubes and quite complicated. The heat transfer coefficients for D = 0.51 mm increased with heat flux but were almost independent of mass flux. Although the heat transfer coefficients were higher than those for a conventional tube with D = 10.3 mm and for pool boiling in the low quality region, they decreased gradually with increasing quality. The heat transfer coefficients for D = 0.30 mm were higher than those for D = 0.51 mm and were almost independent of both mass flux and heat flux.

Comparison of 30 Boiling and Condensation Correlations for Two-Phase Flows in Compact Plate-Fin Heat Exchangers

2017 ◽  
Author(s):  
Wenhai Li ◽  
Ken Alabi ◽  
Foluso Ladeinde
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Flow Boiling ◽  
Transfer Coefficients ◽  
Two Phase Flows ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Heat Exchanger Design ◽  
Micro Channels ◽  
Vertical Tubes

Over the years, empirical correlations have been developed for predicting saturated flow boiling [1–15] and condensation [16–30] heat transfer coefficients inside horizontal/vertical tubes or micro-channels. In the present work, we have examined 30 of these models, and modified many of them for use in compact plate-fin heat exchangers. However, the various correlations, which have been developed for pipes and ducts, have been modified in our work to make them applicable to extended fin surfaces. The various correlations have been used in a low-order, one-dimensional, finite-volume type numerical integration of the flow and heat transfer equations in heat exchangers. The NIST’s REFPROP database [31] is used to account for the large variations in the fluid thermo-physical properties during phase change. The numerical results are compared with Yara’s experimental data [32]. The validity of the various boiling and condensation models for a real plate-fin heat exchanger design is discussed. The results show that some of the modified boiling and condensation correlations can provide acceptable prediction of heat transfer coefficient for two-phase flows in compact plate-fin heat exchangers.

Cooling of a Finned Cylinder by a Jet Flow of Air

2003 ◽  
Author(s):  
F. Gori ◽  
M. Borgia ◽  
A. Doro Altan
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Wall Temperature ◽  
Experimental Tests ◽  
Jet Flow ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Electric System ◽  
Heat Transfer Coefficients ◽  
Convective Heat Transfer Coefficients

Experimental tests have been carried out to evaluate the heat transfer characteristics on an externally finned cylinder impinged by a jet flow of air. The cylinder is internally heated with an electric system. Thermocouples located inside the cylinder allow to evaluate the wall temperature distribution, in order to calculate the local and average convective heat transfer coefficients.

Two-Phase Pressure Drop and Boiling Heat Transfer in a Single Horizontal Microchannel

2006 ◽  
Author(s):  
Cheol Huh ◽  
Moo Hwan Kim
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Local Flow ◽  
Heat Transfer Coefficients ◽  
Phase Pressure

With a single microchannel and a series of microheaters made with MEMS technique, two-phase pressure drop and local flow boiling heat transfer were investigated using deionized water in a single horizontal rectangular microchannel. The test microchannel has a hydraulic diameter of 100 μm and length of 40 mm. A real time observation of the flow patterns with simultaneous measurement are made possible. Tests are performed for mass fluxes of 90, 169, and 267 kg/m2s and heat fluxes of from 100 to 600 kW/m2. The experimental local flow boiling heat transfer coefficients and two-phase frictional pressure gradient are evaluated and the effects of heat flux, mass flux, and vapor qualities on flow boiling are studied. Both the evaluated experimental data are compared with existing correlations. The experimental heat transfer coefficients are nearly independent on mass flux and the vapor quality. Most of all correlations do not provide reliable heat transfer coefficients predictions with vapor quality and prediction accuracy. As for two-phase pressure drop, the measured pressure drop increases with the mass flux and heat flux. Most of all existing correlations of two-phase frictional pressure gradient do not predict the experimental data except some limited conditions.

Thermoreflectance Wall Temperature Measurement in Annular Two-Phase Flow

2019 ◽  
Author(s):  
Jason Chan ◽  
Brian E. Fehring ◽  
Roman W. Morse ◽  
Kristofer M. Dressler ◽  
Gregory F. Nellis ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Wall Temperature ◽  
Annular Flow ◽  
High Heat ◽  
High Heat Flux ◽  
Phase Flow ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Dry Out

Abstract A thermoreflectance method to measure wall temperature in two-phase annular flow is described. In high heat flux conditions, momentary dry-out occurs as the liquid film vaporizes, resulting in dramatic decreases in heat transfer coefficient. Simultaneous liquid and vapor thermoreflectance measurements allow calculations of instantaneous and time-averaged heat transfer coefficients. Validation, calibration and uncertainty of the technique are discussed.

Experimental Study on Flow Boiling Heat Transfer in an Extremely Small Tube

2006 ◽  
Author(s):  
Haruhiko Ohta ◽  
Koichi Inoue ◽  
Yuichiro Shimada
Keyword(s):  
Heat Transfer ◽  
Forced Convection ◽  
Flow Boiling ◽  
Vapor Quality ◽  
Heat Transfer Characteristics ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
Flow Boiling Heat Transfer ◽  
Small Tube

Flow boiling heat transfer in a single small tube is investigated by using FC72 as a working fluid. The heat transfer coefficients are measured in the ranges of heat flux 2–24kW/m2 and mass velocity 100–400kg/m2s under the condition of near atmospheric pressure. Test tube, made of stainless steel, has an inner diameter of 0.51mm and a heated length of 200mm. The tube is located horizontally in a vacuum chamber to reduce the heat loss and to minimize the time to obtain data regarded as that of steady state. In the single-phase region, heat transfer coefficients due to forced convection are in good agreement with the values from the conventional theories. In the saturated region, measured heat transfer characteristics are quite different depending on whether the test liquid is deaerated or not deaerated before the experiments. By using deaerated liquid, three different heat transfer regimes are observed: In the first regime, the heat transfer is dominated by nucleate boiling in low vapor quality, and the heat transfer is deteriorated or enhanced depending on the channel confinement and heat flux. In the second regime, the heat transfer is dominated by two-phase forced convection in moderate quality as is well known for the tubes of normal size. In the third regime, the heat transfer is dominated again by two-phase forced convection, but is deteriorated in high quality. One or two regimes can disappear or become unclear depending on the conditions of flow and heating. The effects of vapor quality and mass velocity on the heat transfer characteristics due to two-phase forced convection in the moderate vapor quality are clarified in the experimental ranges tested. And a reason for the gradual heat transfer deterioration observed in high quality is discussed based on the liquid-vapor behaviors inherent in small diameter tubes.

Investigation of Two Phase Heat Transfer Coefficients of Cryogenic Mixed Refrigerants

2013 ◽  
Author(s):  
Seungwhan Baek ◽  
Sangkwon Jeong
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Microchannel Heat Exchanger ◽  
Heat Transfer Coefficients ◽  
Evaporation Heat ◽  
Two Phase Heat Transfer

Mixed Refrigerant Joule Thomson (MR-JT) refrigerators are widely used in various kinds of cryogenic systems these days. Although heat transfer coefficient estimation for a multiphase and multi-component fluid in cryogenic temperature range is necessarily required in the heat exchanger design of MR-JT refrigerator, it has been rarely discussed so far. In this paper, condensation and evaporation heat transfer coefficients of mixed refrigerant are measured in a microchannel heat exchanger. Printed Circuit Heat Exchanger (PCHE) has been developed as a compact microchannel heat exchanger and used in the experiment. Several two-phase heat transfer coefficient correlations are examined to discuss the experimental measurement results. The result of this paper shows that cryogenic mixed refrigerant heat transfer coefficients can be estimated by conventional two-phase heat transfer coefficient correlations.

Spatial and Temporal Wall Temperature Fluctuations in Two-Phase Flow in Microgap Coolers

2010 ◽  
Author(s):  
Jessica Sheehan ◽  
Avram Bar-Cohen
Keyword(s):  
Heat Transfer ◽  
High Heat ◽  
Heat Fluxes ◽  
Operating Conditions ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Heat Transfer Coefficients ◽  
High Heat Transfer ◽  
Volumetric Cooling ◽  
Very High

Heat transfer to an evaporating refrigerant and/or dielectric liquid in a microgap channel can provide very high heat transfer coefficients and volumetric cooling rates. Recent studies at Maryland have established the dominance of the annular flow regime in such microgap channels and related the observed high-quality peak of an M-shaped heat transfer coefficient curve to the onset of local dryout. The present study utilizes infrared thermography to locate such nascent dryout regions and operating conditions. Data obtained with a 210 micron microgap channel, operated with a mass flux of 195.2 kg/m2-s and heat fluxes of 10.3 to 26 W/cm2 are presented and discussed.

Sign in / Sign up

Export Citation Format

Share Document