Transient Pool Boiling of Water on a Vertical Surface With a Step in Heat Generation

1962 ◽  
Vol 84 (3) ◽  
pp. 217-224 ◽  
Author(s):  
Henry Lurie ◽  
H. A. Johnson
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Heat Generation ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Vertical Surface ◽  
Steady State Temperature ◽  
Nucleate Boiling Heat Transfer ◽  
Time Required ◽  
Phd Thesis

This paper is based on the PhD thesis investigation by H. Lurie [1] on the transient heat transfer from a vertical submerged metallic ribbon undergoing a step in Joule heating leading to boiling on its surface. The tests were made in deaerated distilled water at atmospheric pressure with pool temperatures at saturation and 112 deg F subcooled, and with heat generation rates per unit of ribbon surface area from nonboiling to 1.6 × 106 Btu/ft2hr. Although the heat capacity of the ribbon is low, the surface temperature overshoot compared to the steady-state temperature is minor with values of less than 10 deg F. The time required to reach this overshoot, or the time required to reach steady state, is very short and decreases with increasing heat flux. These values are short compared to Goldstein and Eckert [2] and Siegel’s [3] estimates of the time required to develop the hydro-dynamic and thermal boundary layers in natural convection, and indicate that nucleate boiling heat transfer is probably a weak function of the fluid circulation. Some further support for this is evidenced by calculated transient temperatures based on steady nucleate boiling heat transfer which are in reasonable agreement with the measured performance.

An Overview: Analysis of Heat and Mass Transfer in Fractal Media by Fractal Geometry and Technique

2010 ◽  
Author(s):  
Boming Yu
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Porous Media ◽  
Heat And Mass Transfer ◽  
Oil Recovery ◽  
Fractal Geometry ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Fractal Media ◽  
Nucleate Boiling Heat Transfer

In the past three decades, fractal geometry and technique have received considerable attention due to its wide applications in sciences and technologies such as in physics, mathematics, geophysics, oil recovery, material science and engineering, flow and heat and mass transfer in porous media etc. The fractal geometry and technique may become particularly powerful when they are applied to deal with random and disordered media such as porous media, nanofluids, nucleate boiling heat transfer. In this paper, a summary of recent advances is presented in the areas of heat and mass transfer in fractal media by fractal geometry technique. The present overview includes a brief summary of the fractal geometry technique applied in the areas of heat and mass transfer; thermal conductivities of porous media and nanofluids; nucleate boiling heat transfer. A few comments are made with respect to the theoretical studies that should be made in the future.

Visualization of Boiling Heat Transfer on Micro Porous Coated Surface in Confined Space

2013 ◽  
Author(s):  
Chien-Yuh Yang ◽  
Chien-Fu Liu
Keyword(s):  
Heat Transfer ◽  
Heat Exchangers ◽  
Boiling Heat Transfer ◽  
Heat Transfer Performance ◽  
Heating Surface ◽  
Nucleate Boiling ◽  
Confined Space ◽  
Two Phase ◽  
Nucleate Boiling Heat Transfer ◽  
Coated Surface

Numerous researches have been developed for pool boiling on microporous coated surface in the past decade. The nucleate boiling heat transfer was found to be increased by up to 4.5 times than that on uncoated surface. Recently, the two-phase micro heat exchangers have been considered for high flux electronic devices cooling. The enhancement techniques for improving the nucleate boiling heat transfer performance in the micro heat exchangers have gotten more importance. Previous studies of microporous coatings, however, have been restricted to boiling in unconfined space. No studies have been made on the feasibility of using microporous coatings for enhancing boiling in confined spaces. This study provides an experimental observation of the vapor generation and leaving processes on microporous coatings surface in a 1-mm confined space. It would be helpful for understanding the mechanism of boiling heat transfer and improving the design of two-phase micro heat exchangers. Aluminum particles of average diameter 20 μm were mixed with a binder and a carrier to develop a 150 μm thickness boiling enhancement paint on a 3.0 cm by 3.0 cm copper heating surface. The heating surface was covered by a thin glass plate with a 1 mm spacer to form a 1 mm vertical narrow space for the test section. The boiling phenomenon was recorded by a high speed camera. In addition to the three boiling regimes observed by Bonjour and Lallemand [1], i.e., isolated deformed bubbles, coalesced bubbles and partial dryout at low, moderate and high heat fluxes respectively in unconfined space, a suction and blowing process was observed at the highest heat flux condition. Owing to the space confinement, liquid was sucked and vapor was expelled periodically during the bubble generation process. This mechanism significantly enhanced the boiling heat transfer performance in confined space.

Pool Boiling Heat Transfer with Nanotube Arrays Surface on Titanium

2012 ◽  
Vol 550-553 ◽  
pp. 2913-2916 ◽  
Author(s):  
Jin Liang Tao ◽  
Xin Liang Wang ◽  
Pei Hua Shi ◽  
Xiao Ping Shi
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Heat Transfer Performance ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Test Fluid ◽  
Porous Coating ◽  
Pool Boiling Heat Transfer ◽  
Nucleate Boiling Heat Transfer ◽  
Boiling Heat Transfer Coefficient

In this paper, a new porous coating was formed directly on the surface of titanium metal via anodic oxidation. And by the SEM, the morphology of the coating, which is composed of well-ordered perpendicular nanotubes, was characterized. Moreover, taking deionized water as the test fluid, a visualization study of the coating on its pool boiling heat transfer performance was made. The results demonstrated that compared with the smooth surface, the nucleate boiling heat transfer coefficient can increase 3 times while the nucleate boiling super heat was reduced 30%.

Boiling Heat Transfer and Critical Heat Flux Enhancement of Upward- and Downward-Facing Heater in Nanofluids

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Muhamad Zuhairi Sulaiman ◽  
Masahiro Takamura ◽  
Kazuki Nakahashi ◽  
Tomio Okawa
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Flux Enhancement ◽  
Optimum Configuration ◽  
Wall Superheat ◽  
Nucleate Boiling Heat Transfer

Boiling heat transfer (BHT) and critical heat flux (CHF) performance were experimentally studied for saturated pool boiling of water-based nanofluids. In present experimental works, copper heaters of 20 mm diameter with titanium-oxide (TiO2) nanocoated surface were produced in pool boiling of nanofluid. Experiments were performed in both upward and downward facing nanofluid coated heater surface. TiO2 nanoparticle was used with concentration ranging from 0.004 until 0.4 kg/m3 and boiling time of tb = 1, 3, 10, 20, 40, and 60 mins. Distilled water was used to observed BHT and CHF performance of different nanofluids boiling time and concentration configurations. Nucleate boiling heat transfer observed to deteriorate in upward facing heater, however; in contrast effect of enhancement for downward. Maximum enhancements of CHF for upward- and downward-facing heater are 2.1 and 1.9 times, respectively. Reduction of mean contact angle demonstrate enhancement on the critical heat flux for both upward-facing and downward-facing heater configuration. However, nucleate boiling heat transfer shows inconsistency in similar concentration with sequence of boiling time. For both downward- and upward-facing nanocoated heater's BHT and CHF, the optimum configuration denotes by C = 400 kg/m3 with tb = 1 min which shows the best increment of boiling curve trend with lowest wall superheat ΔT = 25 K and critical heat flux enhancement of 2.02 times.

Sign in / Sign up

Export Citation Format

Share Document