scholarly journals Discussion: “Aerodynamic Design and Performance of Five-Stage Transonic Axial-Flow Compressor” (Kovach, Karl, and Sandercock, D. M., 1961, ASME J. Eng. Power, 83, pp. 303–320)

1961 ◽  
Vol 83 (3) ◽  
pp. 320-321
Author(s):  
P. Schwaar
Keyword(s):  
Axial Flow ◽  
Aerodynamic Design ◽  
Axial Flow Compressor ◽  
And Performance ◽  
Flow Compressor

Aerodynamic Design and Performance of Five-Stage Transonic Axial-Flow Compressor

1961 ◽  
Vol 83 (3) ◽  
pp. 303-320 ◽  
Author(s):  
Karl Kovach ◽  
D. M. Sandercock
Keyword(s):  
Research Work ◽  
Axial Flow ◽  
Performance Characteristics ◽  
Research Center ◽  
Aerodynamic Design ◽  
Axial Flow Compressor ◽  
Turbojet Engine ◽  
And Performance ◽  
Flow Compressor ◽  
Work Done

A five-stage axial-flow compressor with all rotors operating with transonic relative inlet Mach numbers was designed as a research vehicle at the Lewis Research Center in 1952. The compressor was designed and tested as a component of a turbojet engine. This paper summarizes the research work done on this compressor including the aerodynamic design and detailed performance characteristics.

Aerodynamic Design and Testing of an Axial Flow Compressor for the GT24/26 Gas Turbines

2013 ◽  
Author(s):  
Damir Novak ◽  
Michael Loetzerich ◽  
Matthias Boese
Keyword(s):  
Gas Turbines ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Leading Edge ◽  
Advanced Technology ◽  
Aerodynamic Design ◽  
3D Design ◽  
Axial Flow Compressor ◽  
Stage Matching ◽  
Flow Compressor

A 22-stage axial flow compressor with a pressure ratio 35:1 has been designed, built and successfully tested for a heavy-duty gas turbine application. Advanced technology and aero engine design tools have been used. The compressor has been designed using an “arbitrary” airfoil blading including 3D design features, like leading edge re-camber, lean, sweep and flowpath contouring. The compressor performance and part load behavior have been improved by accurate stage matching based on whole compressor 3D analyses. The new compressor has been tested in a scaled down rig and validated in the Alstom Test Power Plant (ATPP).The compressor met all design objectives and demonstrated excellent performance. This paper describes the aerodynamic design and test results.

Flow Analysis of Axial Compressor AV63-15 Variable Stator Simulation

2012 ◽  
Vol 532-533 ◽  
pp. 474-478
Author(s):  
Wei Hua Cheng ◽  
Mian Chang Li ◽  
Chuan Peng Li
Keyword(s):  
Flow Analysis ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Axial Flow ◽  
Operating Conditions ◽  
Axial Flow Compressor ◽  
Air Supply ◽  
The Difference ◽  
And Performance ◽  
Flow Compressor

This paper conducts numerical simulation to a 15-stage civil axial flow compressor and obtains its main parameters distribution and performance curve by a full three-dimensional viscid flow computation software. The computation result indicates that, the developed axial flow compressor meets the anticipated design requirements, and satisfies the customers’ indicators. Under the designed compression ratio, the difference between the maximum air supply quantity in summer and the minimum air supply quantity in winter is 22%. By comparing the operating conditions and data analysis, obtained the change trend of axial velocity, static pressure and temperature, and Ma, and discovered that, under opening of 48° and outlet back pressure of 550KPa, flow separation occurred on the section of machine set close to hud, which indicated that operating condition was close to surging condition.

scholarly journals A Turbojet Simulator for Mach Numbers up to 2.0

1972 ◽  
Author(s):  
F. W. Steffen ◽  
E. A. Satmary ◽  
M. R. Vanco ◽  
S. M. Nosek
Keyword(s):  
High Pressure ◽  
Wind Tunnel ◽  
Axial Flow ◽  
Calibration Procedure ◽  
Aerodynamic Design ◽  
Flight Data ◽  
Axial Flow Compressor ◽  
Heated Air ◽  
Turbojet Engine ◽  
Flow Compressor

A turbojet simulator has been designed and fabricated for use in wind tunnel models. The simulator contains a six-stage, axial-flow compressor powered by a three-stage, axial-flow turbine. High pressure heated air was used to drive the turbine. At design conditions, compressor axial flow, turbine exit flow, and a third supplementary flow all entered the exhaust nozzle at equal values of pressure and temperature. Overall aerodynamic design, instrumentation, and calibration procedure is presented. Performance of the device when used to simulate a J-85 turbojet engine at transonic speeds is reported. The installed nozzle performance obtained with the simulator is also discussed and compared with flight data.

Axial flow compressor design†

1999 ◽  
Vol 213 (5) ◽  
pp. 437-449 ◽  
Author(s):  
S. J. Gallimore
Keyword(s):  
Design Process ◽  
Axial Flow ◽  
Point Of View ◽  
Aerodynamic Design ◽  
Basic Principles ◽  
Axial Flow Compressor ◽  
Compressor Design ◽  
Aero Engines ◽  
Flow Compressor ◽  
Practical Constraints

The purpose of this paper is to set out some of the basic principles and rules associated with the design of axial flow compressors, principally for aero-engines, as well as the practical constraints that are inevitably present. The thrust is primarily on the aerodynamic design but this cannot be divorced from the mechanical aspects and so some of these are touched upon but are not gone into so deeply. The paper has been written from the point of view of the designer and tries to cover most of the points that need to be considered in order to produce a successful compressor. The emphasis has been on the theory behind the design process and on minimizing the reliance on empirical rules. However, because of the complexity of the flow, some empiricism still remains.

Sign in / Sign up

Export Citation Format

Share Document