Free Vibration of Initially Stressed Circular Disks

1965 ◽  
Vol 87 (2) ◽  
pp. 258-264 ◽  
Author(s):  
C. D. Mote
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Variable Thickness ◽  
Transverse Vibration ◽  
Fundamental Mode ◽  
Natural Frequencies ◽  
Thermal Environment ◽  
Vibration Characteristics ◽  
Initial Stresses ◽  
Circular Disks

The approximate free vibration characteristics of centrally clamped, variable thickness disks are analyzed by the Rayleigh-Ritz technique. Natural frequencies of transverse vibration are computed, taking into consideration rotational and thermal in-plane stresses as well as purposely induced initial stresses. Initial stresses can significantly raise the minimum disk natural frequency throughout a prescribed rotational and thermal environment. The fundamental mode of disk vibration is one of zero nodal circles and either zero, one, or two nodal diameters, depending upon the disk geometry and the rotational-thermal environment.

Free Vibration of Thin-Walled Open Section Beams With Unconstrained Damping Treatment

1981 ◽  
Vol 48 (1) ◽  
pp. 169-173 ◽  
Author(s):  
S. Narayanan ◽  
J. P. Verma ◽  
A. K. Mallik
Keyword(s):  
Free Vibration ◽  
Cross Section ◽  
Transverse Vibration ◽  
Natural Frequencies ◽  
Vibration Characteristics ◽  
Numerical Results ◽  
Simply Supported ◽  
Clamped Beams ◽  
Thin Walled ◽  
Open Cross Section

Free-vibration characteristics of a thin-walled, open cross-section beam, with unconstrained damping layers at the flanges, are investigated. Both uncoupled transverse vibration and the coupled bending-torsion oscillations, of a beam of a top-hat section, are considered. Numerical results are presented for natural frequencies and modal loss factors of simply supported and clamped-clamped beams.

scholarly journals Effects of Elliptical Hole on the Correlation of Natural Frequency with Buckling Load of Basalt Laminates Composite Plates

2020 ◽  
Vol 27 (1) ◽  
pp. 216-225
Author(s):  
Buntheng Chhorn ◽  
WooYoung Jung
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Basalt Fiber ◽  
Orientation Angle ◽  
Elliptical Hole ◽  
Composite Plates ◽  
Buckling Load ◽  
Mode Shapes ◽  
Geometric Ratio

AbstractRecently, basalt fiber reinforced polymer (BFRP) is acknowledged as an outstanding material for the strengthening of existing concrete structure, especially it was being used in marine vehicles, aerospace, automotive and nuclear engineering. Most of the structures were subjected to severe dynamic loading during their service life that may induce vibration of the structures. However, free vibration studied on the basalt laminates composite plates with elliptical cut-out and correlation of natural frequency with buckling load has been very limited. Therefore, effects of the elliptical hole on the natural frequency of basalt/epoxy composite plates was performed in this study. Effects of stacking sequence (θ), elliptical hole inclination (ϕ), hole geometric ratio (a/b) and position of the elliptical hole were considered. The numerical modeling of free vibration analysis was based on the mechanical properties of BFRP obtained from the experiment. The natural frequencies as well as mode shapes of basalt laminates composite plates were numerically determined using the commercial program software (ABAQUS). Then, the determination of correlation of natural frequencies with buckling load was carried out. Results showed that elliptical hole inclination and fiber orientation angle induced the inverse proportion between natural frequency and buckling load.

Vibration of Beams with a Single Delamination under Axial Loading

2011 ◽  
Vol 675-677 ◽  
pp. 477-480
Author(s):  
Dong Wei Shu
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Analytical Solutions ◽  
Axial Load ◽  
Natural Frequencies ◽  
Axial Loading ◽  
Composite Beams ◽  
Mode Shapes ◽  
Equilibrium Conditions ◽  
Monotonic Relation

In this work analytical solutions are developed to study the free vibration of composite beams under axial loading. The beam with a single delamination is modeled as four interconnected Euler-Bernoulli beams using the delamination as their boundary. The continuity and the equilibrium conditions are satisfied between the adjoining beams. The studies show that the sizes and the locations of the delaminations significantly influence the natural frequencies and mode shapes of the beam. A monotonic relation between the natural frequency and the axial load is predicted.

Sheet Material Property Effects upon Dynamic Behavior in Self-Pierce Riveted Joints

2011 ◽  
Vol 675-677 ◽  
pp. 999-1002 ◽  
Author(s):  
Xiao Cong He
Keyword(s):  
Natural Frequency ◽  
Transverse Vibration ◽  
Spot Welding ◽  
Sheet Material ◽  
Vibration Characteristics ◽  
Efficient Design ◽  
Material Density ◽  
Sheet Materials ◽  
Riveted Joints ◽  
Free Transverse Vibration

Self-pierce riveting (SPR) technology offers an alternative to resistance spot welding (RSW) for joining sheet materials. It has been found that the SPR technology produced a much stronger joint than the RSW in fatigue test. For efficient design of SPR structures, the knowledge of dynamic characteristics of the SPR beams is essential. In this paper, the free transverse vibration characteristics of single lap-jointed cantilevered SPR beams are investigated in detail. The focus of the analysis is to reveal the influence on the natural frequency and natural frequency ratio of these beams caused by variations in the material properties of sheet materials to be jointed. It is shown that the transverse natural frequencies of single lap jointed cantilevered SPR beams increase significantly as the Young’s modulus of the sheet materials increases, but change slightly corresponding to the change in Poisson’s ratio. It is also found that the material density of the sheets have significant effects on the free transverse vibration characteristics of the beams.

scholarly journals Vibrational Analysis on Hemp and Okra Fibres Mixed Glass Fiber Polyester Composite

2021 ◽  
Vol 8 (11) ◽  
pp. 55-62
Author(s):  
Putti Venkata Siva Teja ◽  
Badatala Ooha ◽  
Kondeti Sravanth
Keyword(s):  
Glass Fiber ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Fiber Composite ◽  
Fem Analysis ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Machine Component ◽  
Free System ◽  
Glass Fiber Composite

In transverse vibrations the element moves to and fro in a direction perpendicular to the direction of the advance of the wave. To determine the vibration characteristics i.e., natural frequencies and mode shapes, modal analysis is a process for a structure or a machine component while is being designed. In real life, aero planes, missiles, rockets, space vehicles, satellites, sub marines etc are modeled as free-free mechanical systems. In this paper an attempt was made to compare natural frequency for two composite materials- ladies finger with Glass fiber composite and Hemp with Glass fiber composite by taking as cantilever beams. The cantilever beam which is fixed at one end is vibrated to obtain the natural frequency, mode shapes at four different modes. A simple low cost demonstration experiment is performed in this paper by using common apparatus in order to compare theoretical, numerical (FEM analysis) profiles of two free-free thin two rectangular composite beams of dimensions 305*49.5* 7 in mm. Keywords: Natural frequencies, Mode shapes, Vibration characteristics, Ladies finger fiber, Hemp fiber, Glass fiber, FEM analysis, Free-Free system.

scholarly journals Wave Based Method for Free Vibration Analysis of Ring Stiffened Cylindrical Shell with Intermediate Large Frame Ribs

2013 ◽  
Vol 20 (3) ◽  
pp. 459-479 ◽  
Author(s):  
Meixia Chen ◽  
Jianhui Wei ◽  
Kun Xie ◽  
Naiqi Deng ◽  
Guoxiang Hou
Keyword(s):  
Cylindrical Shell ◽  
Free Vibration ◽  
Boundary Conditions ◽  
Natural Frequencies ◽  
Free Vibration Analysis ◽  
Structure Type ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Arbitrary Boundary ◽  
Stiffened Cylindrical Shell

Wave based method which can be recognized as a semi-analytical and semi-numerical method is presented to analyze the free vibration characteristics of ring stiffened cylindrical shell with intermediate large frame ribs for arbitrary boundary conditions. According to the structure type and the positions of discontinuities, the model is divided into different substructures whose vibration field is expanded by wave functions which are exactly analytical solutions to the governing equations of the motions of corresponding structure type. Boundary conditions and continuity equations between different substructures are used to form the final matrix to be solved. Natural frequencies and vibration mode shapes are calculated by wave based method and the results show good agreement with finite element method for clamped-clamped, shear diaphragm – shear diaphragm and free-free boundary conditions. Free vibration characteristics of ring stiffened cylindrical shells with intermediate large frame ribs are compared with those with bulkheads and those with all ordinary ribs. Effects of the size, the number and the distribution of intermediate large frame rib are investigated. The frame rib which is large enough is playing a role as bulkhead, which can be considered imposing simply supported and clamped constraints at one end of the cabin and dividing the cylindrical shell into several cabins vibrating separately at their own natural frequencies.

scholarly journals Free Vibration Characteristics of Cylindrical Shells Using a Wave Propagation Method

2001 ◽  
Vol 8 (2) ◽  
pp. 71-84 ◽  
Author(s):  
A. Ghoshal ◽  
S. Parthan ◽  
D. Hughes ◽  
M.J. Schulz
Keyword(s):  
Cylindrical Shell ◽  
Wave Propagation ◽  
Free Vibration ◽  
Periodic Structure ◽  
Natural Frequencies ◽  
Vibration Characteristics ◽  
Structural Element ◽  
Lower Bounding ◽  
Nodal Points ◽  
Wave Propagation Method

In the present paper, concept of a periodic structure is used to study the characteristics of the natural frequencies of a complete unstiffened cylindrical shell. A segment of the shell between two consecutive nodal points is chosen to be a periodic structural element. The present effort is to modify Mead and Bardell's approach to study the free vibration characteristics of unstiffened cylindrical shell. The Love-Timoshenko formulation for the strain energy is used in conjunction with Hamilton's principle to compute the natural propagation constants for two shell geometries and different circumferential nodal patterns employing Floquet's principle. The natural frequencies were obtained using Sengupta's method and were compared with those obtained from classical Arnold-Warburton's method. The results from the wave propagation method were found to compare identically with the classical methods, since both the methods lead to the exact solution of the same problem. Thus consideration of the shell segment between two consecutive nodal points as a periodic structure is validated. The variations of the phase constants at the lower bounding frequency for the first propagation band for different nodal patterns have been computed. The method is highly computationally efficient.

FREE VIBRATION ANALYSIS OF DISCRETELY STIFFENED SKEW PLATES

2001 ◽  
Vol 01 (01) ◽  
pp. 125-144 ◽  
Author(s):  
HUAN ZENG ◽  
CHARLES W. BERT
Keyword(s):  
Free Vibration ◽  
Boundary Conditions ◽  
Natural Frequencies ◽  
Ritz Method ◽  
Free Vibration Analysis ◽  
Vibration Characteristics ◽  
Skew Angle ◽  
Various Boundary Conditions ◽  
Skew Plate ◽  
Convergence Study

Stiffened skew plates find application in various engineering fields. The free vibration characteristics of such plates have been studied by various methods. An orthogonally stiffened skew plate is a skew plate with stiffeners running orthogonal to two opposite edges. To the best knowledge of the present investigators, no previous work has been done for free vibration characteristics of skew plates of such stiffening geometry. The present work studies the free vibration of such plates. The pb-2 Rayleigh–Ritz method was employed due to its accuracy and computational efficiency. The conventional finite element method was also used as a comparative check. A convergence study was first performed for various boundary conditions. Then the vibration of orthogonally stiffened skew plates with different boundary conditions was studied. Close agreement was found between these two methods. The variations of natural frequencies with different parameters, including skew angle ϕ, edge ratio b/a, and height-thickness ratio f/h, were investigated for three types of boundary conditions.

Free Vibration Characteristics of SPR Joints

2006 ◽  
Author(s):  
Xiaocong He ◽  
Ian Pearson ◽  
Ken Young
Keyword(s):  
Aluminum Alloy ◽  
Free Vibration ◽  
Torsional Vibration ◽  
Natural Frequencies ◽  
Vibration Characteristics ◽  
Advanced Materials ◽  
Mode Shapes ◽  
Stress Distributions ◽  
Numerical Examples ◽  
Different Characteristics

Self-piercing riveting (SPR) has drawn more attention in recent years because it can join some advanced materials that are hard to weld, such as aluminum alloy sheets. In this paper, the free torsional vibration characteristics of single lap-jointed encastre SPR beam are investigated in detail. The focus of the analysis is to reveal the influence on the torsional natural frequencies and mode shapes of the single lap-jointed encastre SPR beam of different characteristics of sheets to be jointed. Numerical examples show that the torsional natural frequencies increase significantly as the Young’s modulus of the sheets increase, but almost no change corresponding to the change in Poisson’s ratio of the sheets to be joint. The mode shapes show that there are different deformations in the jointed section of SPR beam compared with the reference encastre beam without joint. These different deformations may cause different natural frequency values and different stress distributions.

Sign in / Sign up

Export Citation Format

Share Document