scholarly journals Discussion: “Stability of the High-Speed Journal Bearing Under Steady Load: 2—The Compressible Film” (Cheng, H. S., and Trumpler, P. R., 1963, ASME J. Eng. Ind., 85, pp. 274–279)

1963 ◽  
Vol 85 (3) ◽  
pp. 279-279
Author(s):  
E. J. Gunter
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Steady Load

Stability of the High-Speed Journal Bearing Under Steady Load: 1—The Incompressible Film

1962 ◽  
Vol 84 (3) ◽  
pp. 351-357 ◽  
Author(s):  
M. M. Reddi ◽  
P. R. Trumpler
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Orbital Motion ◽  
Hydrodynamic Force ◽  
Nonlinear Differential Equations ◽  
Equations Of Motion ◽  
Static Equilibrium ◽  
The Stability ◽  
External Loads ◽  
Steady Load

The phenomenon of oil-film whirl in bearings subjected to steady external loads is analyzed. The journal, assumed to be a particle mass, is subjected to the action of two forces; namely, the external load acting on the bearing and the hydrodynamic force developed in the fluid film. The resulting equations of motion for a full-film bearing and a 180-deg partial-film bearing are developed as pairs of second-order nonlinear differential equations. In evaluating the hydrodynamic force, the contribution of the shear stress on the journal surface is found to be negligible for the full-film bearing, whereas for the partial-film bearing it is found to be significant at small attitude values. The equations of motion are linearized and the coefficients of the resulting characteristic equations are studied for the stability of the static-equilibrium positions. The full-film bearing is found to have no stable static-equilibrium position, whereas the 180-deg partial-film bearing is found to have stable static-equilibrium positions under certain parametric conditions. The equations of motion for the full-film bearing are integrated numerically on a digital computer. The results show that the journal center, depending on the parametric conditions, acquired either an orbital motion or a dynamical path of increasing attitude terminating in bearing failure.

scholarly journals Improvement of Tilting-Pad Journal Bearing Operating Characteristics by Application of Eddy Grooves

Lubricants ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 18
Author(s):  
Eckhard Schüler ◽  
Olaf Berner
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Load Capacity ◽  
Fluid Film ◽  
Operating Characteristics ◽  
Fluid Film Bearings ◽  
Tilting Pad ◽  
Bearing Load ◽  
Bearing Loads ◽  
Tilting Pad Journal Bearing

In high speed, high load fluid-film bearings, the laminar-turbulent flow transition can lead to a considerable reduction of the maximum bearing temperatures, due to a homogenization of the fluid-film temperature in radial direction. Since this phenomenon only occurs significantly in large bearings or at very high sliding speeds, means to achieve the effect at lower speeds have been investigated in the past. This paper shows an experimental investigation of this effect and how it can be used for smaller bearings by optimized eddy grooves, machined into the bearing surface. The investigations were carried out on a Miba journal bearing test rig with Ø120 mm shaft diameter at speeds between 50 m/s–110 m/s and at specific bearing loads up to 4.0 MPa. To investigate the potential of this technology, additional temperature probes were installed at the crucial position directly in the sliding surface of an up-to-date tilting pad journal bearing. The results show that the achieved surface temperature reduction with the optimized eddy grooves is significant and represents a considerable enhancement of bearing load capacity. This increase in performance opens new options for the design of bearings and related turbomachinery applications.

Sign in / Sign up

Export Citation Format

Share Document