scholarly journals Effect of Combined Stress on Yield and Fracture Behavior of Zircaloy-2

1961 ◽  
Vol 83 (4) ◽  
pp. 499-508 ◽  
Author(s):  
R. L. Mehan
Keyword(s):  
Plastic Flow ◽  
Biaxial Tension ◽  
Effective Strain ◽  
Tension Stress ◽  
Combined Stress ◽  
Flow Properties ◽  
Axial Tension ◽  
Fracture Ductility ◽  
Stress States ◽  
Single Stress

The yielding and fracture characteristics of Zircaloy-2 as a function of stress state were investigated at room temperature through the medium of thin-walled cylindrical specimens under internal pressure and axial tension. Stress states from uniaxial longitudinal tension to uniaxial tangential tension were examined. Two tests at elevated temperature were performed at a single stress ratio. It was found that the fracture ductility lessened with increasing biaxiality. A minimum in ductility was found at balanced biaxial tension where the fracture ductility, as expressed by the effective strain, was 29 per cent. The yielding and plastic flow properties were found to be highly anisotropic. Two methods were used to express the plastic flow data: a graphical approach and a theoretical analysis based on a theory proposed by R. Hill, either one of which is suitable to express the flow properties of Zircaloy-2 under various states of combined stress.

Anisotropic Loading Functions for Combined Stresses in the Plastic Range

1955 ◽  
Vol 22 (1) ◽  
pp. 77-85
Author(s):  
L. W. Hu ◽  
Joseph Marin
Keyword(s):  
Plastic Flow ◽  
Biaxial Tension ◽  
Strain History ◽  
Test Results ◽  
Axial Tension ◽  
State Of Stress ◽  
Loading Function ◽  
Combined Stresses ◽  
Shift Of Origin ◽  
Tubular Specimens

Abstract A loading function is a relation between combined stresses for which the beginning of plastic flow takes place. The loading function for a given material is different depending upon the initial plastic strains produced. That is, the initial stress or strain history influences the subsequent loading function. This paper gives the results of an experimental investigation to determine the validity of certain loading functions proposed for anisotropic materials. The study reported was conducted for an aluminum alloy 24S-T and the state of stress covered was biaxial tension. These stresses were produced in the usual way by subjecting thin-walled tubular specimens to axial tension and internal pressure. The test results showed that none of the existing loading functions is adequate for interpreting the plastic stress-strain relations obtained. Tests also were made to determine the change in the loading function with increase in plastic flow. It was found that the loading function did not remain symmetrical with respect to the original function, nor was the new loading function the same as the original except for a shift of origin. However, the test results support in a qualitative way the concept of the so-called “yield corner.”

Biaxial Strength of HY 80 Steel

1985 ◽  
Vol 107 (2) ◽  
pp. 132-137 ◽  
Author(s):  
K. S. Chan ◽  
U. S. Lindholm ◽  
J. Wise
Keyword(s):  
Biaxial Tension ◽  
Strain Ratio ◽  
Thin Wall ◽  
Plastic Strain Ratio ◽  
Axial Tension ◽  
Diffuse Necking ◽  
Stress States ◽  
Von Mises ◽  
Tube Geometry ◽  
Good Agreement

The biaxial deformation behavior of HY 80 steel has been examined by testing thin wall tubes under combined axial tension and internal pressure. The effective stress-strain curves and the hardening response have been found to vary with the stress state. The plastic strain ratio at a given stress ratio deviates from the von Mises value except at the stress states near uniaxial tension, plane strain and equi-biaxial tension. Using Drucker theory, these deviations are eliminated and the resulting yield locus is in good agreement with both the Bishop-Hill theory and the experimental results. Influenced by the tube geometry, the instability strains at the onset of diffuse necking are decreased by an increase in hoop tension. The diffuse necking strains are reasonably predicted by the Swift and the Lankford-Saibel/Mellor criteria.

Comparison of Substructures Between Uniaxial and Biaxial Deformation in 1100-0 Aluminum

1981 ◽  
Vol 39 ◽  
pp. 52-53
Author(s):  
D. L. Rohr ◽  
S. S. Hecker
Keyword(s):  
Plastic Strain ◽  
Cell Walls ◽  
Room Temperature ◽  
Mechanical Response ◽  
Biaxial Tension ◽  
Initial Deformation ◽  
Uniaxial Deformation ◽  
Biaxial Deformation ◽  
Stress States ◽  
Comprehensive Study

As part of a comprehensive study of microstructural and mechanical response of metals to uniaxial and biaxial deformations, the development of substructure in 1100 A1 has been studied over a range of plastic strain for two stress states.Specimens of 1100 aluminum annealed at 350 C were tested in uniaxial (UT) and balanced biaxial tension (BBT) at room temperature to different strain levels. The biaxial specimens were produced by the in-plane punch stretching technique. Areas of known strain levels were prepared for TEM by lapping followed by jet electropolishing. All specimens were examined in a JEOL 200B run at 150 and 200 kV within 24 to 36 hours after testing.The development of the substructure with deformation is shown in Fig. 1 for both stress states. Initial deformation produces dislocation tangles, which form cell walls by 10% uniaxial deformation, and start to recover to form subgrains by 25%. The results of several hundred measurements of cell/subgrain sizes by a linear intercept technique are presented in Table I.

scholarly journals A Study of Yielding and Plasticity of Rapid Prototyped ABS

Mathematics ◽  
2021 ◽  
Vol 9 (13) ◽  
pp. 1495
Author(s):  
Dan-Andrei Șerban ◽  
Cosmin Marșavina ◽  
Alexandru Viorel Coșa ◽  
George Belgiu ◽  
Radu Negru
Keyword(s):  
Experimental Data ◽  
Stress State ◽  
Plastic Flow ◽  
Plane Stress ◽  
Yield Criterion ◽  
Numerical Analyses ◽  
Flow Potential ◽  
Stress States ◽  
State Configuration

In this article, the yielding and plastic flow of a rapid-prototyped ABS compound was investigated for various plane stress states. The experimental procedures consisted of multiaxial tests performed on an Arcan device on specimens manufactured through photopolymerization. Numerical analyses were employed in order to determine the yield points for each stress state configuration. The results were used for the calibration of the Hosford yield criterion and flow potential. Numerical analyses performed on identical specimen models and test configurations yielded results that are in accordance with the experimental data.

Research of stamping of unequal channel bars. Part 3. Force parameters and shape change of the billet when extruding channels. 1. Kinematic and stress states of the billet

2021 ◽  
pp. 65-71
Author(s):  
A.L. Vorontsov
Keyword(s):  
Plastic Flow ◽  
Complete System ◽  
Shape Change ◽  
Plane Deformation ◽  
System Of Equations ◽  
Flow Rates ◽  
Die Forging ◽  
The Matrix ◽  
Stress States ◽  
Theory Of Plastic Flow

On the basis of the complete system of equations of the theory of plastic flow, the kinematic and stress states of the billet are determined when the channels are extruded under conditions of plane deformation of the misaligned position of the punch and the matrix. Keywords: die forging, extrusion, misaligned position, punch, matrix, plane deformation, plastic flow rates, stresses. [email protected]

Evaluating plastic flow properties by characterizing indentation size effect using a sharp indenter

2008 ◽  
Vol 56 (14) ◽  
pp. 3338-3343 ◽  
Author(s):  
Ju-Young Kim ◽  
Seung-Kyun Kang ◽  
Julia R. Greer ◽  
Dongil Kwon
Keyword(s):  
Size Effect ◽  
Plastic Flow ◽  
Indentation Size Effect ◽  
Flow Properties ◽  
Indentation Size

Improvement of Axial Tension Distribution of Bolted Joints Tightened by Calibrated Wrench Method From Viewpoint of Quality and Process Control Using Elliptical Confidence Limit

2019 ◽  
Author(s):  
Soichi Hareyama ◽  
Ken-ichi Manabe ◽  
Satoshi Kobayashi
Keyword(s):  
Process Control ◽  
Statistical Method ◽  
Confidence Limit ◽  
Bolted Joints ◽  
Independent Random Variables ◽  
Tension Stress ◽  
Bolted Joint ◽  
Tightening Torque ◽  
Tension Distribution ◽  
Axial Tension

Abstract When tightening a large number of bolted joints, the calibrated wrench method is used. Since this method is indirect, the axial tension varies greatly in many cases. However, the calibrated wrench method is still widely used because of the simplicity of the tool and easy standardization. When the tightening torque and axial tension are considered to be two independent random variables, the axial tension (stress) is distributed within an elliptical confidence limit. Conventionally, it is thought that the shape of this distribution is a rhombus. Considering the permitted limit for a working load (stress) on a bolted joint, the elliptical variation has a larger margin to the yield point than that of a conventional rhombus. On the basis of this feature, we show in this paper that a higher tightening target torque and a higher axial tension can be set than before. By applying the elliptical confidence limit, one can obtain higher tightening torque and initial axial tension than the conventional values within a smaller range of variations. In this study, in the case of tightening a large number of bolted joints at factories and so forth, tightening reliability is considered as a problem associated with quality or process control and a probabilistic statistical method is investigated. Finally, we carry out analysis to establish the optimum tightening torque for bolted joints.

Sign in / Sign up

Export Citation Format

Share Document