Closure to “Discussions of ‘Lubrication Phenomena in Spur Gears: Capacity, Film Thickness Variation, and Efficiency’” (1965, ASME J. Basic Eng., 87, pp. 663–664)

1965 ◽  
Vol 87 (3) ◽  
pp. 664-665
Author(s):  
R. Wayne Adkins ◽  
E. I. Radzimovsky
Keyword(s):  
Film Thickness ◽  
Thickness Variation ◽  
Spur Gears

Lubrication Phenomena in Spur Gears: Capacity, Film Thickness Variation, and Efficiency

1965 ◽  
Vol 87 (3) ◽  
pp. 655-663 ◽  
Author(s):  
R. Wayne Adkins ◽  
E. I. Radzimovsky
Keyword(s):  
Shear Stress ◽  
Film Thickness ◽  
Pressure Distribution ◽  
Power Loss ◽  
Hydrodynamic Lubrication ◽  
Thickness Variation ◽  
Spur Gears ◽  
Oil Film ◽  
Lubrication Conditions ◽  
Lubricant Viscosity

In this paper the oil film separating the mating surfaces of involute spur gears operating under hydrodynamic lubrication conditions is analyzed. This analysis surpasses previous analyses in as much as the actual motion of the involute profiles (rolling, sliding, and squeezing motion) and the total number of teeth engaged at any one time are considered. Expressions are derived for the pressure distribution, shear stress, and power loss in the oil film at any phase of tooth engagement. A method is developed by which these expressions can be applied to determine the film thickness at any instant and the power loss for a given load, speed, and lubricant viscosity.

Application of dynamic mesh technology in the oil film flow simulation for hydrostatic bearing

2019 ◽  
Vol 71 (1) ◽  
pp. 146-153
Author(s):  
Yanqin Zhang ◽  
Zhiquan Zhang ◽  
Xiangbin Kong ◽  
Rui Li ◽  
Hui Jiang
Keyword(s):  
Film Thickness ◽  
Flow Velocity ◽  
Manufacturing Industry ◽  
Dynamic Mesh ◽  
Lubricating Oil ◽  
Thickness Variation ◽  
Content Type ◽  
Oil Film ◽  
Rotating Speed ◽  
Hydrostatic Bearing

Purpose The purpose of this paper was to obtain the lubrication characteristics of heavy hydrostatic bearing in heavy equipment manufacturing industry through theoretical analysis and numerical simulation. Design/methodology/approach This paper discusses the influence of oil film thickness variation on velocity field, outlet-L and outlet-R flow velocity under the hydrostatic bearing running in no-load 0 N, load 400 KN, full load 1,500 KN and rotating speeds of 10 r/min, 20 r/min, 30 r/min, 40 r/min, 50 r/min and 60 r/min, by using dynamic mesh technology and FLUENT software. Findings When the working table rotates clockwise, in the change process of oil film thickness, the fluid flow pattern of the lubricating oil at the edge of the sealing oil is the rule of laminar flow, and the oil cavity has a vortex. The outlet-R flow velocity becomes higher and higher by increasing the bearing load and working table speed, and the flow velocity increases with the decrease in oil film thickness; the outlet-L flow velocity increases with the decrease in oil film thickness under low rotating speed (less than 10 r/min) condition and decreases with the decrease of oil film thickness under high rotating speed (more than 60 r/min) condition. Originality/value The influence of the oil film thickness on the flow state distribution of the oil film was analyzed under different working conditions, and the influence rules of oil film thickness on the flow velocity of hydrostatic bearing oil pad was obtained by using dynamic mesh technology.

Sign in / Sign up

Export Citation Format

Share Document