Elastoplastic Stress and Strain Distribution in a Finite Plate With a Circular Hole Subjected to Unidimensional Load

1963 ◽  
Vol 30 (1) ◽  
pp. 115-121 ◽  
Author(s):  
A. J. Durelli ◽  
C. A. Sciammarella
Keyword(s):  
Experimental Determination ◽  
Circular Hole ◽  
Strain Distribution ◽  
Stress And Strain ◽  
Hardening Material ◽  
Finite Plate ◽  
Elastoplastic Stress ◽  
Moire Method ◽  
Stress And Strain Distribution

This paper deals with the experimental determination of the elastoplastic stress and strain distribution around an empty circular hole in a finite aluminum plate subjected to a unidimensional load as the deformation increases from the elastic far into the plastic field. The strains were measured using the moire method. The stresses were computed by means of the Prandtl-Reuss stress-strain relationships presented in a convenient form for the case of a strain-hardening material.

Effect of Corner Shape on Elastic Stress and Strain Concentration in Plates With an Oblique Hole

1973 ◽  
Vol 95 (1) ◽  
pp. 151-157 ◽  
Author(s):  
F. Ellyin ◽  
U. M. Izmiroglu
Keyword(s):  
Strain Distribution ◽  
Elastic Stress ◽  
Steel Plates ◽  
Stress And Strain ◽  
Plate Model ◽  
Strain Concentration ◽  
Controlling Variables ◽  
Stress And Strain Distribution ◽  
Insight Into

The effect of the corner cut on the elastic stress and strain concentration in plates containing an oblique hole is studied. Fourteen steel plates with different corner break configurations and varying angles of inclinations are tested. This study has resulted in the determination of the effective range of the controlling variables for a “radius tip” or a “vertical cut”. An investigation of this nature is of interest in the design of oblique nozzle connections in pressure vessel heads and shells. It provides an insight into the nature of stresses in skewed holes and nozzle attachments. Previous works [3, 8] have shown the applicability of the plate model to the oblique nozzle connection, and present study fills the gap with regards to the effect of acute corner cut on the stress and strain distribution.

Effect of pipe expansion on the redistribution of residual stresses after molding

2020 ◽  
Vol 10 (2) ◽  
pp. 122-126
Author(s):  
Nikolay A. Makhutov ◽  
◽  
Dmitry A. Neganov ◽  
Eugeny P. Studenov ◽  
◽  
...  
Keyword(s):  
Residual Stresses ◽  
Strain Distribution ◽  
Strain State ◽  
Stress And Strain ◽  
Cylindrical Shape ◽  
Pipe Material ◽  
Pipe Expansion ◽  
Calculation Results ◽  
Residual Deformations ◽  
Stress And Strain Distribution

In the factory, pipes for trunk oil and oil product pipelines are obtained by molding and welding. To ensure a cylindrical shape and reduce technological residual stresses, expansion technology is used. Pipe expansion causes a significant change in the values of residual deformations and stresses. The article presents both the calculation results and graphs regarding stress and strain distribution during bending of the stock and their redistribution after expansion. Based on the calculation results, the final total values of residual stresses and residual deformations caused by bending and expansion were stated to be important components of the stress-strain state observed in pipelines being operated under cyclic loading, as well as those used in assessing how degradation affects the ductility of the pipe material. These factors were concluded as being reasonably taken into account when performing verification calculations regarding long-running pipelines if, based on their diagnostics and analysis, their state does not meet modern strength requirements.

Study on Stress and Strain of Anchorage Using Finite Element Method

2013 ◽  
Vol 325-326 ◽  
pp. 1314-1317
Author(s):  
Cong Sheng Chen ◽  
Ping He ◽  
Cheng Yong Wang ◽  
Xue Hui Chen ◽  
Lei Huang ◽  
...  
Keyword(s):  
Finite Element ◽  
Strain Distribution ◽  
Maximum Stress ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Integrated Modeling ◽  
Stress And Strain ◽  
Steel Strand ◽  
Prestressed State ◽  
Stress And Strain Distribution

Three-dimensional integrated modeling method and the numerical simulation of elastoplastic finite element are adopted in the paper. The mechanical response of the five holes anchorage is analyzed in certain prestressed state. The stress and strain distribution information of the anchor ring, clip and steel strand is obtained respectively, and the structure safety is discussed by investigating on the maximum stress and strain.

Application of Moire Methods to the Determination of Transient Stress and Strain Distributions

1962 ◽  
Vol 29 (1) ◽  
pp. 23-29 ◽  
Author(s):  
W. F. Riley ◽  
A. J. Durelli
Keyword(s):  
Strain Distribution ◽  
Stress And Strain ◽  
Two Dimensional ◽  
Distribution Problem ◽  
Principal Stresses ◽  
Transient Stress ◽  
Optical Phenomenon ◽  
Moiré Effect ◽  
Fringe Patterns

When two arrays of lines are superimposed an optical phenomenon known as the moire effect is observed under certain conditions. This moire effect is used by the authors to determine the distribution of transient strains on the surface of two-dimensional bodies. The method can be used to solve completely the strain-distribution problem or it can be used in combination with photoelasticity to separate the principal stresses. The methods used in interpreting the moire fringe patterns and the techniques used to produce the patterns are described in the paper. Two applications are discussed.

Finite Element Analysis of Metal Flow of Finishing Groove in Hot Continuous Rolling Bar

2012 ◽  
Vol 510 ◽  
pp. 667-672
Author(s):  
Jia Lin Zhou ◽  
Chen Gang Pan ◽  
Xiao Yong Zhang
Keyword(s):  
Strain Distribution ◽  
Metal Flow ◽  
Dimensional Accuracy ◽  
Stress And Strain ◽  
Fe Model ◽  
Element Analysis ◽  
Iron And Steel ◽  
Expansion Angle ◽  
The Stability ◽  
Stress And Strain Distribution

This article established 3D FE model of dual-radius arc finishing groove and tangent expansion angle finishing groove using ANSYS / LS-DYNA software for Wuhan Iron and Steel plant Ф16 hot continuous bar, and analyzed metal flow pattern, stress and strain distribution of two types finishing grooves. The results show that surface stress and strain distribution of dual-radius arc finishing groove have better uniform than them of tangent expansion angle finishing groove, and dual-radius arc finishing groove ensures the stability of the rolled piece in finishing groove, improve the dimensional accuracy and surface quality of rolled finishing product.

Sign in / Sign up

Export Citation Format

Share Document