Boiling Heat-Transfer Data at Low Heat Flux

1967 ◽  
Vol 89 (3) ◽  
pp. 235-242 ◽  
Author(s):  
W. C. Elrod ◽  
J. A. Clark ◽  
E. R. Lady ◽  
H. Merte
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Convection Heat Transfer ◽  
Solid Material ◽  
Nucleate Boiling ◽  
Suspended Solid ◽  
Dissolved Gas ◽  
Horizontal Tubes ◽  
Saturated Water

Data are presented for natural and forced convection heat transfer from the outside of a single 3/4-in-dia tube to saturated water in the pressure range from 535 to 1550 psia. Nonboiling and nucleate boiling at low heat flux are considered for vertical and horizontal tubes. Water chemistry control is shown to be important in obtaining reproducible data. A new factor, suspended solid material in the boiling medium, is found to influence the nucleate boiling data in a manner similar to that of a dissolved gas.

Boiling Heat Transfer and Critical Heat Flux Enhancement of Upward- and Downward-Facing Heater in Nanofluids

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Muhamad Zuhairi Sulaiman ◽  
Masahiro Takamura ◽  
Kazuki Nakahashi ◽  
Tomio Okawa
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Flux Enhancement ◽  
Optimum Configuration ◽  
Wall Superheat ◽  
Nucleate Boiling Heat Transfer

Boiling heat transfer (BHT) and critical heat flux (CHF) performance were experimentally studied for saturated pool boiling of water-based nanofluids. In present experimental works, copper heaters of 20 mm diameter with titanium-oxide (TiO2) nanocoated surface were produced in pool boiling of nanofluid. Experiments were performed in both upward and downward facing nanofluid coated heater surface. TiO2 nanoparticle was used with concentration ranging from 0.004 until 0.4 kg/m3 and boiling time of tb = 1, 3, 10, 20, 40, and 60 mins. Distilled water was used to observed BHT and CHF performance of different nanofluids boiling time and concentration configurations. Nucleate boiling heat transfer observed to deteriorate in upward facing heater, however; in contrast effect of enhancement for downward. Maximum enhancements of CHF for upward- and downward-facing heater are 2.1 and 1.9 times, respectively. Reduction of mean contact angle demonstrate enhancement on the critical heat flux for both upward-facing and downward-facing heater configuration. However, nucleate boiling heat transfer shows inconsistency in similar concentration with sequence of boiling time. For both downward- and upward-facing nanocoated heater's BHT and CHF, the optimum configuration denotes by C = 400 kg/m3 with tb = 1 min which shows the best increment of boiling curve trend with lowest wall superheat ΔT = 25 K and critical heat flux enhancement of 2.02 times.

Study on Subcooled-Forced Flow Boiling Heat Transfer and Critical Heat Flux of Solid-Water Two-Phase Mixture

1999 ◽  
Author(s):  
Yasuo Koizumi ◽  
Hiroyasu Ohtake ◽  
Manabu Mochizuki
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Liquid Layer ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Forced Flow ◽  
Superheated Liquid ◽  
Flow Boiling Heat Transfer

Abstract The effect of solid particle introduction on subcooled-forced flow boiling heat transfer and a critical heat flux was examined experimentally. In the experiment, glass beads of 0.6 mm diameter were mixed in subcooled water. Experiments were conducted in a range of the subcooling of 40 K, a velocity of 0.17–6.7 m/s, a volumetric particle ratio of 0–17%. When particles were introduced, the growth of a superheated liquid layer near a heat trasnsfer surface seemed to be suppressed and the onset of nucleate boiling was delayed. The particles promoted the condensation of bubbles on the heat transfer surface, which shifted the initiation of a net vapor generation to a high heat flux region. Boiling heat trasnfer was augmented by the particle introduction. The suppression of the growth of the superheated liquid layer and the promotion of bubble condensation and dissipation by the particles seemed to contribute that heat transfer augmentation. The wall superheat at the critical heat flux was elevated by the particle introduction and the critical heat flux itself was also enhanced. However, the degree of the critical heat flux improvement was not drastic.

Some Possible Critical Conditions in Nucleate Boiling

1963 ◽  
Vol 85 (2) ◽  
pp. 89-99 ◽  
Author(s):  
Yan-Po Chang
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Maximum Rate ◽  
Unit Area ◽  
Heating Surface ◽  
Nucleate Boiling ◽  
Critical Conditions ◽  
Bubble Generation ◽  
Basic Ideas

The primary purpose of this paper is to introduce into boiling heat transfer certain basic ideas from which several critical conditions are derived. The heat transfer in nucleate boiling is considered as being limited by the maximum rate of bubble generation from a unit area of the heating surface. With certain simplified assumptions, an equation is obtained for the first critical heat flux of nucleate boiling with and without forced convection and subcooling.

scholarly journals Discussion of the Heat Flux Calculation Method During Pool Boiling on Meshed Heaters

2020 ◽  
Vol 2 (1) ◽  
pp. 247-252
Author(s):  
Łukasz J. Orman ◽  
Norbert Radek ◽  
Jacek Pietraszek ◽  
Dariusz Gontarski
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Distilled Water ◽  
Determination Method ◽  
Nucleate Boiling Heat Transfer ◽  
Calculation Results ◽  
Very High

AbstractThe paper discusses nucleate boiling heat transfer on meshed surfaces during pool boiling of distilled water and ethyl alcohol of very high purity. It presents a correlation for heat flux developed for heaters covered with microstructural coatings made of meshes. The experimental results have been compared with the calculation results performed using the correlation and have been followed by discussion. Conclusions regarding the heat flux determination method have been drawn with the particular focus on the usefulness of the considered model for heat flux calculations on samples with sintered mesh layers.

scholarly journals ELETRIC FIELD ENHANCEMENT AND DETERIORATION OF BOILING HEAT TRANSFER AND CRITICAL HEAT FLUX IN DIELECTRIC FLUIDS

2001 ◽  
Vol 1 (1) ◽  
pp. 32
Author(s):  
P. M. Carrica ◽  
V. Masson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Electric Fields ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Film Boiling ◽  
Two Phase ◽  
Boiling Regime ◽  
Dielectric Fluids

We present the results of an experimental study of the effects of externally imposed electric fields on boiling heat transfer and critical heat flux (CHF) in dielectric fluids. The study comprises the analysis of geometries that, under the effects of electric fields, cause the bubbles either to be pushed toward the heater or away from it. A local phase detection probe was used to measure the void fraction and the interfacial impact rate near the heater. It was found that the critical heat flux can be either augmented or reduced with the application of an electric field, depending on the direction of . In addition, the heat transfer can be slightly enhanced or degraded depending on the heat flux. The study of the two-phase flow in nucleate boiling, only for the case of favorable dielectrophoretic forces, reveals that the application of an electric field reduces the bubble detection time and increases the detachment frequency. It also shows that the two-phase flow characteristics of the second film boiling regime resemble more a nucleate boiling regime than a film boiling regime.

A Photographic Study of Boiling in the Absence of Gravity

1959 ◽  
Vol 81 (3) ◽  
pp. 230-236 ◽  
Author(s):  
R. Siegel ◽  
C. Usiskin
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Boiling Heat Transfer ◽  
High Speed ◽  
Free Fall ◽  
Nucleate Boiling ◽  
Zero Gravity ◽  
Experimental Equipment ◽  
Boiling Process ◽  
Qualitative Effect

A photographic study was made to determine the qualitative effect of zero gravity on the mechanism of boiling heat transfer. The experimental equipment included a container for boiling water and a high-speed motion-picture camera. To eliminate the influence of gravity, these were mounted on a platform which was allowed to fall freely approximately 8 ft. During the free fall, photographs were taken of boiling from various surface configurations such as electrically heated horizontal and vertical ribbons. The heat flux was varied to produce conditions from moderate nucleate boiling to burnout. The results indicate that gravity plays a considerable role in the boiling process, especially in connection with the motion of vapor within the liquid.

The Critical Heat Flux in Nucleate Boiling Heat Transfer: Part I—The Chemical Actuator Mechanism

2009 ◽  
Author(s):  
M. R. Reda
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Grain Boundaries ◽  
Recent Work ◽  
Boiling Heat Transfer ◽  
Nucleate Boiling ◽  
Passive Layer ◽  
Nucleate Boiling Heat Transfer ◽  
Good Agreement

Nucleate boiling heat transfer is first introduced and the literature is reviewed. It was concluded that the passive layer and the grain boundaries are responsible for the transfer to the nucleate boiling regime. Based on the recent work of Biener and his collaborators (Nature Material 2008) and the Gibbs rule of thermodynamics, a possible mechanism was outlined. The mechanism assumes that each grain in the passive layer act as a chemical actuator which is driven by microstructure phase change. The new mechanism agrees well with the experimental results, in good agreement with previous models and can explain why and how CHF occurs.

Effect of Heat Flux on Pool Boiling Heat Transfer Enhancement (Numerical Investigation Approach)

2020 ◽  
Author(s):  
T. S. Mogaji ◽  
O. A. Sogbesan ◽  
Tien-Chien Jen
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Numerical Investigation ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Transfer Enhancement

Abstract This study presents numerical investigation results of heat flux effect on pool boiling heat transfer enhancement during nucleate boiling heat transfer of water. The simulation was performed for five different heated surfaces such as: brass, copper, mild steel, stainless steel and aluminum using ANSYS simulation software at 1 atmospheric pressure. The samples were heated in a domain developed for bubble growth during nucleate boiling process under the same operational condition of applied heat flux ranged from 100 to 1000 kW/m2 and their corresponding heat transfer coefficient was obtained numerically. Obtained experimental data of other authors from the open literature result is in close agreement with the simulated data, thus confirming the validity of the CFD simulation method used in this study. It is found that heat transfer coefficient increases with increasing heat flux. The results revealed that in comparison to other materials tested, better heat transfer performance up to 38.5% and 7.11% is observed for aluminum and brass at lower superheated temperature difference conditions of 6.96K and 14.01K respectively. This behavior indicates better bubble development and detachment capability of these heating surface materials and could be used in improving the performance of thermal devices toward producing compact and miniaturized equipment.

Effect of Pressure, Subcooling, and Dissolved Gas on Pool Boiling Heat Transfer From Microporous Surfaces in FC-72

2003 ◽  
Vol 125 (1) ◽  
pp. 75-83 ◽  
Author(s):  
K. N. Rainey ◽  
S. M. You ◽  
S. Lee
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Heat Transfer Performance ◽  
Nucleate Boiling ◽  
Gas Content ◽  
Absolute Pressure ◽  
Dissolved Gas ◽  
Test Conditions ◽  
Nucleate Boiling Heat Transfer ◽  
Surface Correlations

The present research is an experimental study of the effects of pressure, subcooling, and non-condensable gas (air) on the pool nucleate boiling heat transfer performance of a microporous enhanced and a plain (machine-roughened) reference surface. The test surfaces, 1-cm2 flat copper blocks in the horizontal, upward facing orientation, were immersed in FC-72. The test conditions included an absolute pressure range of 30–150 kPa, a liquid subcooling range of 0 (saturation) to 50 K, and both gas-saturated and pure subcooling conditions. Effects of these parameters on nucleate boiling and critical heat flux (CHF) were investigated. Results showed that, in general, the effects of pressure and subcooling on both nucleate boiling and CHF were consistent with the prevailing trends in the literature. For the present heater geometry, the effects of dissolved gas on the boiling performance were generally small, however, as the dissolved gas content increased (through either increased pressure or subcooling) more of the nucleate boiling curve was affected (enhanced). The enhancement of CHF from increased liquid subcooling was greater for the microporous surface than the plain surface. Correlations for both nucleate boiling and CHF were also presented.

Sign in / Sign up

Export Citation Format

Share Document