Prediction of the Low Cycle Fatigue Life of Pressure Vessels

1967 ◽  
Vol 89 (4) ◽  
pp. 858-868 ◽  
Author(s):  
A. G. Pickett ◽  
S. C. Grigory
Keyword(s):  
Fatigue Life ◽  
Stress Analysis ◽  
Pressure Vessel ◽  
Low Cycle Fatigue ◽  
Design Procedure ◽  
Pressure Vessels ◽  
Analysis Method ◽  
Notch Stress ◽  
Fatigue Life Analysis ◽  
Fatigue Evaluation

The bases for ASME Boiler and Pressure Vessel Code, Section III, fatigue evaluation procedures, the fracture mechanics approach to fatigue life analysis, and the notch stress analysis method are reviewed. Fatigue life predictions are compared with the results of materials, model, and full size pressure vessel tests performed for PVRC and AEC. These tests were made in response to the research objectives established by ASME Special Committee to Review Code Stress Basis in 1958. A proposed design procedure based on the notch stress analysis method and experimental results is presented.

Design of Pressure Vessels for Low-Cycle Fatigue

1962 ◽  
Vol 84 (3) ◽  
pp. 389-399 ◽  
Author(s):  
B. F. Langer
Keyword(s):  
Fatigue Strength ◽  
Pressure Vessel ◽  
Low Cycle Fatigue ◽  
Fatigue Curve ◽  
Pressure Vessels ◽  
Reduction Factor ◽  
Strength Reduction ◽  
Strength Reduction Factor ◽  
The Mean ◽  
Fatigue Evaluation

Methods are described for constructing a fatigue curve based on strain-fatigue data for use in pressure vessel design. When this curve is used, the same fatigue strength-reduction factor should be used for low-cycle as for high-cycle conditions. When evaluating the effects of combined mean and alternating stress, the fatigue strength-reduction factor should be applied to both the mean and the alternating component, but then account must be taken of the reduction in mean stress which can be produced by yielding. The complete fatigue evaluation of a pressure vessel can be a major task for the designer, but it can be omitted, or at least drastically reduced, if certain requirements can be met regarding design details, inspection, and magnitude of transients. Although the emphasis in this paper is on pressure vessel design, the same principles could be applied to any structure made of ductile metal and subjected to limited numbers of load cycles.

Prediction of Low-Cycle Fatigue Life of Specimens With Fabrication Flaws

1968 ◽  
Vol 90 (4) ◽  
pp. 620-626 ◽  
Author(s):  
A. G. Pickett
Keyword(s):  
Fatigue Life ◽  
Crack Initiation ◽  
Low Cycle Fatigue ◽  
Small Specimen ◽  
Cycle Fatigue ◽  
Notch Stress ◽  
Weld Defect ◽  
Life Analysis ◽  
Fatigue Life Analysis ◽  
Crack Initiation Life

A modification of the notch stress procedure for fatigue-life analysis is presented. The importance of considering the mechanics of the specimen and the effects of the notch on specimen mechanics is illustrated by example. The procedure is applied to correlate the results of small specimen tests with large weld defect specimen tests. The significance of crack-initiation life and crack-propagation life and the dependence of these portions of total fatigue life on specimen geometry and loading is developed.

Life Prediction of Composite Pressure Vessels Using Multi-Scale Approach

2010 ◽  
Author(s):  
Sung Kyu Ha ◽  
Stephen W. Tsai ◽  
Seong Jong Kim ◽  
Khazar Hayat ◽  
Kyo Kook Jin
Keyword(s):  
Fatigue Life ◽  
Stress Analysis ◽  
Pressure Vessel ◽  
Composite Structures ◽  
Life Prediction ◽  
Pressure Vessels ◽  
Multi Scale ◽  
Helical Angle ◽  
Composite Pressure Vessel ◽  
Composite Pressure Vessels

A multi-scale fatigue life prediction methodology of composite pressure vessels subjected to multi-axial loading has been proposed in this paper. The multi-scale approach starts from the constituents, fiber, matrix and interface, leading to predict behavior of ply, laminates and eventually the composite structures. The life prediction methodology is composed of two steps: macro stress analysis and micro mechanics of failure based on fatigue analysis. In the macro stress analysis, multiaxial fatigue loading acting at laminate is determined from finite element analysis (FEM) of composite pressure vessel, and ply stresses are computed using a classical laminate theory (CLT). The micro-scale stresses are calculated in each constituent (i.e. matrix, interface, and fiber) from ply stresses using a micromechanical model. Micromechanics of failure (MMF) was originally developed to predict the strength of composites and now extended to prediction of fatigue life. Two methods are employed in predicting fatigue life of each constituent, i.e. an equivalent stress method for multi-axially loaded matrix, and a critical plane method for the interface. A modified Goodman diagram is used to take into account the generic mean stresses. Damages from each loading cycle are accumulated using Miner’s rule. Each fiber is assumed to follow a probabilistic failure depending on the length. Using the overall micro and macro models established in this study, Monte Carlo simulation has been performed to predict the overall fatigue life of a composite pressure vessel considering statistical distribution of material properties of each constituent and manufacturing winding helical angle.

A Study on Fatigue Life Evaluation of Pressure Vessel Made of ASME SA240-316L Material Using Numerical Analysis

2019 ◽  
Vol 893 ◽  
pp. 1-5 ◽  
Author(s):  
Eui Soo Kim
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Pressure Vessel ◽  
Life Prediction ◽  
Pressure Vessels ◽  
Physical Damage ◽  
Element Analysis ◽  
Internal Damage ◽  
Life Evaluation ◽  
Fatigue Life Evaluation

Pressure vessels are subjected to repeated loads during use and charging, which can causefine physical damage even in the elastic region. If the load is repeated under stress conditions belowthe yield strength, internal damage accumulates. Fatigue life evaluation of the structure of thepressure vessel using finite element analysis (FEA) is used to evaluate the life cycle of the structuraldesign based on finite element method (FEM) technology. This technique is more advanced thanfatigue life prediction that uses relational equations. This study describes fatigue analysis to predictthe fatigue life of a pressure vessel using stress data obtained from FEA. The life prediction results areuseful for improving the component design at a very early development stage. The fatigue life of thepressure vessel is calculated for each node on the model, and cumulative damage theory is used tocalculate the fatigue life. Then, the fatigue life is calculated from this information using the FEanalysis software ADINA and the fatigue life calculation program WINLIFE.

Fatigue and Burst Analysis of Hy-140(T) Steel Pressure Vessels

1970 ◽  
Vol 92 (1) ◽  
pp. 11-16 ◽  
Author(s):  
J. M. Barsom ◽  
S. T. Rolfe
Keyword(s):  
Yield Strength ◽  
Pressure Vessel ◽  
Low Cycle Fatigue ◽  
High Strength Steels ◽  
High Strength ◽  
Fatigue Tests ◽  
Pressure Vessels ◽  
High Yield ◽  
Corrosion Properties ◽  
Burst Analysis

Increasing use of high-strength steels in pressure-vessel design has resulted from emphasis on decreasing the weight of pressure vessels for certain applications. To demonstrate the suitability of a 140-ksi yield strength steel for use in unwelded pressure vessels, HY-140(T)—a quenched and tempered 5Ni-Cr-Mo-V steel—was fabricated and subjected to various burst and fatigue tests, as well as to various laboratory tests. In general, results of the investigation indicated very good tensile, Charpy, Nil Ductility Transition Temperature (NDT), low-cycle fatigue, and stress-corrosion properties of HY-140(T) steels, as well as very good burst tests results, in comparison with existing high-yield strength pressure-vessel steels. The results also indicate that the HY-140(T) steel should be an excellent material for its originally designed purpose, Naval hull applications.

A Study of Nozzles in Pressure Vessels under Pressure Fatigue Loading

1967 ◽  
Vol 182 (1) ◽  
pp. 657-684 ◽  
Author(s):  
J. Spence ◽  
W. B. Carlson
Keyword(s):  
Fatigue Life ◽  
Mild Steel ◽  
Pressure Vessel ◽  
Special Interest ◽  
Maximum Stress ◽  
Fatigue Loading ◽  
Fatigue Tests ◽  
Pressure Vessels ◽  
Full Size

Nozzles in cylindrical vessels have been of special interest to designers for some time and have offered a field of activity for many research workers. This paper presents some static and fatigue tests on five designs of full size pressure vessel nozzles manufactured in two materials. Supporting and other published work is reviewed showing that on the basis of the same maximum stress mild steel vessels give the same fatigue life as low alloy vessels. When compared on the basis of current codes it is shown that mild steel vessels may have five to ten times the fatigue life of low alloy vessels unless special precautions are taken.

Use of Duplex Stainless Steel in Economic Design of a Pressure Vessel

2006 ◽  
Vol 129 (1) ◽  
pp. 155-161 ◽  
Author(s):  
Milan Veljkovic ◽  
Jonas Gozzi
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Stainless Steels ◽  
Pressure Vessel ◽  
Design Procedure ◽  
High Strength Steels ◽  
High Strength ◽  
Pressure Vessels ◽  
Economic Design ◽  
European Standard

Pressure vessels have been used for a long time in various applications in oil, chemical, nuclear, and power industries. Although high-strength steels have been available in the last three decades, there are still some provisions in design codes that preclude a full exploitation of its properties. This was recognized by the European Equipment Industry and an initiative to improve economy and safe use of high-strength steels in the pressure vessel design was expressed in the evaluation report (Szusdziara, S., and McAllista, S., EPERC Report No. (97)005, Nov. 11, 1997). Duplex stainless steel (DSS) has a mixed structure which consists of ferrite and austenite stainless steels, with austenite between 40% and 60%. The current version of the European standard for unfired pressure vessels EN 13445:2002 contains an innovative design procedure based on Finite Element Analysis (FEA), called Design by Analysis-Direct Route (DBA-DR). According to EN 13445:2002 duplex stainless steels should be designed as a ferritic stainless steels. Such statement seems to penalize the DSS grades for the use in unfired pressure vessels (Bocquet, P., and Hukelmann, F., 2001, EPERC Bulletin, No. 5). The aim of this paper is to present an investigation performed by Luleå University of Technology within the ECOPRESS project (2000-2003) (http://www.ecopress.org), indicating possibilities towards economic design of pressure vessels made of the EN 1.4462, designation according to the European standard EN 10088-1 Stainless steels. The results show that FEA with von Mises yield criterion and isotropic hardening describe the material behaviour with a good agreement compared to tests and that 5% principal strain limit is too low and 12% is more appropriate.

scholarly journals Low-cycle fatigue behaviour of laser welded high-strength steel DOMEX 700 MC

2018 ◽  
Vol 157 ◽  
pp. 05013 ◽  
Author(s):  
Peter Kopas ◽  
Milan Sága ◽  
František Nový ◽  
Bohuš Leitner
Keyword(s):  
Fatigue Life ◽  
Welded Joints ◽  
High Strength Steel ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
High Strength ◽  
Fatigue Behaviour ◽  
Total Strain Amplitude ◽  
Cycle Fatigue ◽  
Fatigue Life Analysis

The article presents the results of research on low cycle fatigue strength of laser welded joints vs. non-welded material of high-strength steel DOMEX 700 MC. The tests were performed under load controlled using the total strain amplitude ɛac. The operating principle of the special electro-mechanic fatigue testing equipment with a suitable clamping system was working on 35 Hz frequency. Fatigue life analysis was conducted based on the Manson-Coffin-Basquin equation, which made it possible to determine fatigue parameters. Studies have shown differences in the fatigue life of original specimens and laser welded joints analysed, where laser welded joints showed lower fatigue resistance. In this article a numerical analysis of stresses generated in bending fatigue specimens has been performed employing the commercially available FEM-program ADINA.

Sign in / Sign up

Export Citation Format

Share Document