Velocity Distributions in Two-Phase Vortex Flow

1968 ◽  
Vol 90 (3) ◽  
pp. 368-372
Author(s):  
J. F. Lafferty ◽  
F. G. Hammitt ◽  
R. Cheesewright

An analytical model is developed to describe gas-jet driven two-phase vortex flow. Utilizing experimental data, the model is used to calculate the velocity distributions of the two phases within an air-water vortex. The computed velocities are in very good agreement with independent measurements and with trends predicted from other investigations of single-phase vortex flow.

Author(s):  
Ashish Kotwal ◽  
Che-Hao Yang ◽  
Clement Tang

The current study shows computational and experimental analysis of multiphase flows (gas-liquid two-phase flow) in channels with sudden area change. Four test sections used for sudden contraction and expansion of area in experiments and computational analysis. These are 0.5–0.375, 0.5–0.315, 0.5–0.19, 0.5–0.14, inversely true for expansion channels. Liquid Flow rates ranging from 0.005 kg/s to 0.03 kg/s employed, while gas flow rates ranging from 0.00049 kg/s to 0.029 kg/s implemented. First, single-phase flow consists of only water, and second two-phase Nitrogen-Water mixture flow analyzed experimentally and computationally. For Single-phase flow, two mathematical models used for comparison: the two transport equations k-epsilon turbulence model (K-Epsilon), and the five transport equations Reynolds stress turbulence interaction model (RSM). A Eulerian-Eulerian multiphase approach and the RSM mathematical model developed for two-phase gas-liquid flows based on current experimental data. As area changes, the pressure drop observed, which is directly proportional to the Reynolds number. The computational analysis can show precise prediction and a good agreement with experimental data when area ratio and pressure differences are smaller for laminar and turbulent flows in circular geometries. During two-phase flows, the pressure drop generated shows reasonable dependence on void fraction parameter, regardless of numerical analysis and experimental analysis.


2008 ◽  
Vol 2008 ◽  
pp. 1-9 ◽  
Author(s):  
Jim Meagher ◽  
Xi Wu ◽  
Chris Lencioni

A two-complex-degrees-of-freedom model is developed and compared to experimental data for various amounts of rotor bow and its orientation to mass imbalance of the rotor. The equation of motion is developed by adding constant forces that rotate with the rotor to a Bently-Muszynska two-mode isotropic rotor model with a plane journal bearing. Diagnostic information discernable from probes at the bearing is explored and compared to midspan response, where previous research has concentrated. The model presented also extends earlier work by representing the effect of a nonrigid bearing. Good agreement between the analytical model and experiment demonstrates that the analysis presented can be useful to diagnose and balance residual shaft bow from probes located at the bearings, where vibration data are typically more available than midspan probes.


1985 ◽  
Vol 107 (1) ◽  
pp. 142-151 ◽  
Author(s):  
J. P. Langlinais ◽  
A. T. Bourgoyne ◽  
W. R. Holden

The calculation of single-phase and two-phase flowing pressure gradients in a well annulus is generally based on an extension of empirical correlations developed for Newtonian fluids in circular pipes. Various techniques for extending pipe flow correlations to an annular geometry have been presented in the literature which involve the representation of the annular well geometry with an equivalent circular diameter and the representation of non-Newtonian fluid behavior with an apparent Newtonian viscosity. Unfortunately, little experimental data have been available which would allow a comparison of the relative accuracy of the various proposed techniques. In this study, experimental pressure gradient data have been taken in two 6000-ft wells. Frictional pressure losses for single-phase flow (mud only) in two annuli were compared to values predicted by the Bingham plastic and power law models. These calculations utilized the equivalent diameters defined by the Crittendon criteria, the hydraulic diameter, and the slot approximation. Also, total pressure difference for two-phase flow was measured for one annular geometry. This data was compared to that predicted by the Poettmann and Carpenter, Hagedorn and Brown, Orkiszewski, and Beggs and Brill correlations. Comparison of experimental data with the various prediction techniques was favorable, each having advantage in certain situations. For the data investigated, the Crittendon criteria using a Bingham plastic model gave the best results. The two-phase flow data was best predicted by the Hagedorn and Brown correlation utilizing an equivalent hydraulic diameter.


Author(s):  
Brady Drew ◽  
John Charonko ◽  
Pavlos Vlachos

Entrainment characteristics of two-phase flow (liquid-gas) buoyant jets differ significantly from their single-phase flow counterparts. Past studies have not adequately described the mechanisms that cause the gas jet to entrain liquid from its surroundings and expand. In this work, Particle Image Velocimetry (PIV) and shadowgraph flow visualization experiments have been conducted on submerged round gas jets of varying speeds and nozzle diameters with the goal of improving our understanding of the processes of entrainment and expansion in a two-phase jet. We hypothesize that liquid is entrained into the gas column through (1) shear entrainment due to instabilities at the interface between the fast-moving gas jet and stagnant liquid, and (2) convective entrainment that occurs when the jet begins to pinch off and transform into a bubbly plume. The total entrainment estimated using the PIV measurements is higher than the respective values that single-phase buoyant jet theory suggests, especially at low jet speeds. This may be an effect of increased convective entrainment as the jet slows down. The shadowgraph flow visualization experiments provide valuable information pertaining to the structure of the jet and the interfacial dynamics.


1963 ◽  
Vol 85 (2) ◽  
pp. 137-150 ◽  
Author(s):  
S. Levy

Single-phase turbulent mixing length methods are used to predict two-phase flow. Two-phase density and velocity distributions and two-phase pressure drops are derived by treating the two-phase system as a continuous medium where the turbulent exchanges of momentum and density are equal. Good agreement is obtained between test results and analytical predictions.


2014 ◽  
Vol 2014 ◽  
pp. 1-19 ◽  
Author(s):  
Jorge Pérez Mañes ◽  
Victor Hugo Sánchez Espinoza ◽  
Sergio Chiva Vicent ◽  
Michael Böttcher ◽  
Robert Stieglitz

This paper deals with the validation of the two-phase flow models of the CFD code NEPTUNEC-CFD using experimental data provided by the OECD BWR BFBT and PSBT Benchmark. Since the two-phase models of CFD codes are extensively being improved, the validation is a key step for the acceptability of such codes. The validation work is performed in the frame of the European NURISP Project and it was focused on the steady state and transient void fraction tests. The influence of different NEPTUNE-CFD model parameters on the void fraction prediction is investigated and discussed in detail. Due to the coupling of heat conduction solver SYRTHES with NEPTUNE-CFD, the description of the coupled fluid dynamics and heat transfer between the fuel rod and the fluid is improved significantly. The averaged void fraction predicted by NEPTUNE-CFD for selected PSBT and BFBT tests is in good agreement with the experimental data. Finally, areas for future improvements of the NEPTUNE-CFD code were identified, too.


2005 ◽  
Vol 127 (4) ◽  
pp. 479-486
Author(s):  
Bin Liu ◽  
Mauricio Prado

For any pumping artificial lift system in the petroleum industry, the free gas significantly affects the performance of the pump and the system above the pump. A model, though not a complete two-phase flow model, has been developed for the effective prediction of separation efficiency across a wide range of production conditions. The model presented is divided into two main parts, the single-phase flow-field solution and the bubble-tracking method. The first part of the model solves the single-phase liquid flow field using the computational fluid dynamics approach. Then, a simple bubble-tracking method was applied to estimate the down-hole natural separation efficiency for two-phase flow. A comparison between the results of the model and the experimental data was conducted. It shows a very good agreement with the experimental data for lower gas void fractions (bubble flow regime).


Author(s):  
Christian Weinmu¨ller ◽  
Dimos Poulikakos

Microfluidics has experienced a significant increase in research activities in recent years with a wide range of applications emerging, such as micro heat exchangers, energy conversion devices, microreactors, lab-on-chip devices and micro total chemical analysis systems (μTAS). Efforts to enhance or extend the performance of single phase microfluidic devices are met by two-phase flow systems [1, 2]. Essential for the design and control of microfluidic systems is the understanding of the fluid/hydrodynamic behavior, especially pressure drop correlations. These are well established for single phase flow, however, analytical correlations for two-phase flow only reflect experimentally obtained values within an accuracy of ± 50% [3, 4]. The present study illustrates the effect of two-phase flow regimes on the pressure drop. Experimental measurement data is put into relation of calculated values based on established correlations of Lockhart-Martinelli with Chisholm modifications for macroscopic flows [5, 6] and Mishima-Hibiki modifications for microscale flows [7]. Further, the experimental pressure drop data is superimposed onto two-phase flow maps to identify apparent correlations of pressure drop abnormalities and flow regimes. The experiments were conducted in a square microchannel with a width of 200 μm. Optical access is guaranteed by an anodically bonded glass plate on a MEMS fabricated silicon chip. Superficial velocities range from 0.01 m/s to 1 m/s for the gas flow and from 0.0001 m/s to 1 m/s for the liquid flow with water as liquid feed and CO2 as gas. The analysis of the flow regimes was performed by imaging the distinct flow regimes by laser induced fluorescence microscopy, employing Rhodamine B as the photosensitive dye. The pressure drop was synchronically recorded with a 200 mbar, 2.5 bar and 25 bar differential pressure transmitter and the data was exported via a LabView based software environment, see Figure 1. Figure 2 illustrates the experimentally obtained pressure drop in comparison to the calculated values based on the Lockhard-Martinelli correlation with the Chisholm modification and the Mishima-Hibiki modification. For both cases the predications underestimate the two-phase pressure drop by more than 50%. Nevertheless, the regression of the experimental data has an offset of linear nature. Two-phase flow is assigned to flow regime maps of bubbly, wedging, slug or annular flow defined by superficial gas and liquid velocities. In Figure 3 the pressure drop is plotted as a surface over the corresponding flow regime map. Transition lines indicate a change of flow regimes enclosing an area of an anticline in the pressure data. In the direct comparison between the calculated and the measured values, the two surfaces show a distinct deviation. Especially, the anticline of the experimental data is not explained by the analytical correlations. Figure 4 depicts the findings of Figure 3 at a constant superficial velocity of 0.0232 m/s. The dominant influence of the flow regimes on the pressure drop becomes apparent, especially in the wedging flow regime. The evident deviation of two-phase flow correlations for the pressure drop is based on omitting the influence of the flow regimes. In conclusion, the study reveals a strong divergence of pressure drop measurements in microscale two-phase flow from established correlations of Lockhart-Martinelli and recognized modifications. In reference to [8, 9], an analytical model incorporating the flow regimes and, hence, predicting the precise pressure drop would be of great benefit for hydrodynamic considerations in microfluidics.


Author(s):  
Alan B. Maskal ◽  
Fatih Aydogan

The fuel rods in Pressurized Water Reactor (PWR) and Boiling Water Reactor (BWR) cores are supported by spacer grids. Even though spacer grids add to the pressure loss in the reactor core, spacer grids have several benefits in Light Water Reactors (LWRs). Some of these benefits are: (i) increasing the turbulence at the bottom of the reactor core for better heat transfer in single phase region of the LWRs, (ii) improving the departure nucleate boiling ratio results for PWRs, and (iii) improving critical power ratio (CPR) values by increasing the thickness of film in annular flow regime in the top section of the reactor core of BWRs. Several mathematical models have been developed for single and two phase pressure loss across the grid spacer. Almost all of them significantly depend on Reynolds Number. Spacer designs have evolved (incorporating mixing vanes, springs, dimples, etc), resulting in the complexity of the analysis across the grid, all the models have been compared not only theoretically but also quantitatively. For the quantitative comparisons, this work compares the results of mathematical spacer models with experimental data of BWR Full Size Fine Mesh Bundle Tests (BFBT). The experimental data of BFBT provides very detailed experimental results for pressure drop by using several different boundary condition and detailed pressure drop measurements. Since one CT-scanner was used at the bundle exit and three X-ray densitometers were used for the chordal average void distribution at different elevations to generate the BFBT results, detailed two phase parameters have been measured in BFBT database. Two bundle types of BFBT, the current 8×8 type and the high burn-up 8×8 type, were simulated. Three combinations of radial and axial power shapes were tested: 1) beginning of cycle (BOC) radial power pattern/cosine axial power shape (the C2A pattern); 2) end of cycle (EOC) radial power pattern/cosine axial power shape (C2B pattern); and 3) beginning of cycle radial power pattern/inlet peaked axial power shape (C3 pattern) in BFBT. The pressure drop in BFBT database was measured in both single-phase flow and two-phase flow conditions that cover the normal operational behavior. BFBT database gives the three combinations of high burnup assemblies with different radial and axial power shapes, namely C2A, C2B and C3, which were utilized in the critical power measurements. There are two types of spacers in this program — ferrule type and grid type. Therefore, detailed experimental data of BFBT was used for analyzing mathematical models of spacer grid for various boundary conditions of BWR in this paper. It was observed and discussed that pressure drop values due to spacer models can be significantly different.


2002 ◽  
Vol 755 ◽  
Author(s):  
Shihuai Zhou ◽  
Long-Qing Chen ◽  
Rebecca A. MacKay ◽  
Zi-Kui Li u

ABSTRACTThe phase equilibria and thermodynamic properties of the ternary Ni-Al-Ta system on Ni-rich side were analyzed. Thermodynamic descriptions of the liquid, γ-fcc, γ'-L12, and π-Ni6AlTa phases were obtained using the CALPHAD (CALculation of PHase Diagrams) technique. The thermodynamics of γ-fcc and γ'-L12 phases were modeled with a single Gibbs energy function taking into account the crystallographic relation between the two phases. The ternary interaction parameters of the liquid and fcc phases were also determined. The calculated phase diagrams of the ternary Ni-Al-Ta system show a good agreement with experimental data.


Sign in / Sign up

Export Citation Format

Share Document