scholarly journals Discussion: “Stability Considerations for a Gas-Lubricated Tilting-Pad Journal Bearing. Part 1: Analytical Methods” (Chu, T. Y., McCabe, J. T., and Elrod, H. G., 1968, ASME J. Lubr. Technol., 90, pp. 162–172)

1968 ◽  
Vol 90 (3) ◽  
pp. 639-639
Author(s):  
V. Castelli
Keyword(s):  
Analytical Methods ◽  
Journal Bearing ◽  
Tilting Pad ◽  
Tilting Pad Journal Bearing ◽  
Bearing Part

Stability Considerations for a Gas-Lubricated Tilting Pad Bearing—Part 2: Analytical Refinements and Stability Data

1972 ◽  
Vol 94 (3) ◽  
pp. 223-233 ◽  
Author(s):  
J. T. McCabe ◽  
T. Y. Chu ◽  
H. G. Elrod
Keyword(s):  
Steady State ◽  
Frequency Response ◽  
Journal Bearing ◽  
Design Data ◽  
Tilting Pad ◽  
Stability Data ◽  
Frequency Response Method ◽  
Response Method ◽  
Tilting Pad Journal Bearing ◽  
Bearing Part

A method for generating the film response of a single gas-lubricated tilting pad journal bearing is derived and it is shown how the results can be used to provide both steady-state and stability data for a three pad bearing. The nature of tilting pad bearing stability is discussed with the aid of frequency response plots, mode shape computations and two illustrative limiting cases. In the first, the bearing pivots are locked and the shaft is free to translate; in the second, the rotor is restrained from translating but the pads are free to pitch. Finally, a design example is given and a comparison is made between a three shoe bearing with design data based on the step-jump method and a four shoe bearing with design data based on the frequency response method.

scholarly journals Improvement of Tilting-Pad Journal Bearing Operating Characteristics by Application of Eddy Grooves

Lubricants ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 18
Author(s):  
Eckhard Schüler ◽  
Olaf Berner
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Load Capacity ◽  
Fluid Film ◽  
Operating Characteristics ◽  
Fluid Film Bearings ◽  
Tilting Pad ◽  
Bearing Load ◽  
Bearing Loads ◽  
Tilting Pad Journal Bearing

In high speed, high load fluid-film bearings, the laminar-turbulent flow transition can lead to a considerable reduction of the maximum bearing temperatures, due to a homogenization of the fluid-film temperature in radial direction. Since this phenomenon only occurs significantly in large bearings or at very high sliding speeds, means to achieve the effect at lower speeds have been investigated in the past. This paper shows an experimental investigation of this effect and how it can be used for smaller bearings by optimized eddy grooves, machined into the bearing surface. The investigations were carried out on a Miba journal bearing test rig with Ø120 mm shaft diameter at speeds between 50 m/s–110 m/s and at specific bearing loads up to 4.0 MPa. To investigate the potential of this technology, additional temperature probes were installed at the crucial position directly in the sliding surface of an up-to-date tilting pad journal bearing. The results show that the achieved surface temperature reduction with the optimized eddy grooves is significant and represents a considerable enhancement of bearing load capacity. This increase in performance opens new options for the design of bearings and related turbomachinery applications.

Dynamic Analysis of Tilting-Pad Journal Bearing—Influence of Pad Deformations

1994 ◽  
Vol 116 (3) ◽  
pp. 621-627 ◽  
Author(s):  
H. Desbordes ◽  
M. Fillon ◽  
C. Chan Hew Wai ◽  
J. Frene
Keyword(s):  
Film Thickness ◽  
Pressure Field ◽  
Journal Bearing ◽  
Maximum Pressure ◽  
Tilting Pad ◽  
Minimum Film Thickness ◽  
Dimensional Finite Element ◽  
The One ◽  
Tilting Pad Journal Bearing ◽  
Tilting Pad Journal Bearings

A theoretical nonlinear analysis of tilting-pad journal bearings is presented for small and large unbalance loads under isothermal conditions. The radial displacements of internal pad surface due to pressure field are determined by a two-dimensional finite element method in order to define the actual film thickness. The influence of pad deformations on the journal orbit, on the minimum film thickness and on the maximum pressure is studied. The effects of pad displacements are to decrease the minimum film thickness and to increase the maximum pressure. The orbit amplitude is also increased by 20 percent for the large unbalance load compared to the one obtained for rigid pad.

Tilting Pad Journal Bearings: A Discussion on Stability Calculation, Frequency Dependence, and Pad and Pivot Flexibility

2012 ◽  
Author(s):  
Jason C. Wilkes ◽  
Dara W. Childs
Keyword(s):  
Degrees Of Freedom ◽  
Journal Bearing ◽  
Operating Temperature ◽  
Excitation Frequency ◽  
Full Model ◽  
Stability Calculation ◽  
Damping Coefficients ◽  
Tilting Pad ◽  
Stiffness And Damping ◽  
Tilting Pad Journal Bearing

For several years, researchers have presented predictions showing that using a full tilting-pad journal bearing (TPJB) model (retaining all of the pad degrees of freedom) is necessary to accurately perform stability calculations for a shaft operating on TPJBs. This paper will discuss this issue, discuss the importance of pad and pivot flexibility in predicting impedance coefficients for the tilting-pad journal bearing, present measured changes in bearing clearance with operating temperature, and summarize the differences between measured and predicted frequency dependence of dynamic impedance coefficients. The current work presents recent test data for a 100 mm (4 in) five-pad TPJB tested in load on pad (LOP) configuration. Measured results include bearing clearance as a function of operating temperature, pad clearance and radial displacement of the loaded pad (the pad having the static load vector directed through its pivot), and frequency dependent stiffness and damping. Measured hot bearing clearances are approximately 30% smaller than measured cold bearing clearances and are inversely proportional to pad surface temperature; predicting bearing impedances with a rigid pad and pivot model using these reduced clearances results in overpredicted stiffness and damping coefficients that are several times larger than previous comparisons. The effect of employing a full bearing model versus a reduced bearing model (where only journal degrees of freedom are retained) in a stability calculation for a realistic rotor-bearing system is assessed. For the bearing tested, the bearing coefficients reduced at the frequency of the unstable eigenvalue (subsynchronously reduced) predicted a destabilizing cross-coupled stiffness coefficient at the onset of instability within 1% of the full model, while synchronously reduced coefficients for the lightly loaded bearing required 25% more destabilizing cross-coupled stiffness than the full model to cause system instability. The same stability calculation was performed using measured stiffness and damping coefficients at synchronous and subsynchronous frequencies. These predictions showed that both the synchronously measured stiffness and damping and predictions using the full bearing model were more conservative than the model using subsynchronously measured stiffness and damping, an outcome that is completely opposite from conclusions reached by comparing different prediction models. This contrasting outcome results from a predicted increase in damping with increasing excitation frequency at all speeds and loads; however, this increase in damping with increasing excitation frequency was only measured at the most heavily loaded conditions.

Sign in / Sign up

Export Citation Format

Share Document