Measurement of Temperatures Associated With Bubbles in Subcooled Pool Boiling

1969 ◽  
Vol 91 (1) ◽  
pp. 123-128 ◽  
Author(s):  
J. D. Jacobs ◽  
A. H. Shade
Keyword(s):  
Heat Transfer ◽  
Carbon Tetrachloride ◽  
Heat Source ◽  
Optical System ◽  
High Speed ◽  
Pool Boiling ◽  
Motion Pictures ◽  
Heater Surface ◽  
Subcooled Liquid ◽  
Idealized Model

High-speed motion pictures were taken of initial pool boiling of carbon tetrachloride using a schlieren optical system and associated temperature instrumentation. Many bubbles leaving the heat source were found to be superheated regardless of the degree of subcooling of the liquid. Individual bubbles rising from the heater surface carried a thin laminar layer of hot liquid on their upper surface and trailed a wake of warm liquid. An idealized model of the surrounding warm liquid was empirically developed and accounts for a significant portion of the heat transfer in pool boiling of highly subcooled liquid.

Pool Boiling Characteristics of Metallic Nanofluids

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
K. Hari Krishna ◽  
Harish Ganapathy ◽  
G. Sateesh ◽  
Sarit K. Das
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boiling Heat Transfer ◽  
Volume Fraction ◽  
Pool Boiling ◽  
Heat Fluxes ◽  
Solid Particles ◽  
Heater Surface ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Nanofluids, solid-liquid suspensions with solid particles of size of the order of few nanometers, have created interest in many researchers because of their enhancement in thermal conductivity and convective heat transfer characteristics. Many studies have been done on the pool boiling characteristics of nanofluids, most of which have been with nanofluids containing oxide nanoparticles owing to the ease in their preparation. Deterioration in boiling heat transfer was observed in some studies. Metallic nanofluids having metal nanoparticles, which are known for their good heat transfer characteristics in bulk regime, reported drastic enhancement in thermal conductivity. The present paper investigates into the pool boiling characteristics of metallic nanofluids, in particular of Cu-H2O nanofluids, on flat copper heater surface. The results indicate that at comparatively low heat fluxes, there is deterioration in boiling heat transfer with very low particle volume fraction of 0.01%, and it increases with volume fraction and shows enhancement with 0.1%. However, the behavior is the other way around at high heat fluxes. The enhancement at low heat fluxes is due to the fact that the effect of formation of thin sorption layer of nanoparticles on heater surface, which causes deterioration by trapping the nucleation sites, is overshadowed by the increase in microlayer evaporation, which is due to enhancement in thermal conductivity. Same trend has been observed with variation in the surface roughness of the heater as well.

scholarly journals Effect of Uniformly and Nonuniformly Coated Al2O3 Nanoparticles over Glass Tube Heater on Pool Boiling

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Nitin Doifode ◽  
Sameer Gajghate ◽  
Abdul Najim ◽  
Anil Acharya ◽  
Ashok Pise
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
High Speed ◽  
Pool Boiling ◽  
Glass Tube ◽  
Al2o3 Nanoparticles ◽  
High Speed Camera ◽  
Coated Nanoparticles ◽  
Nucleation Sites ◽  
Coated Surface

Effect of uniformly and nonuniformly coated Al2O3 nanoparticles over plain glass tube heater on pool boiling heat transfer was studied experimentally. A borosilicate glass tube coated with Al2O3 nanoparticle was used as test heater. The boiling behaviour was studied by using high speed camera. Result obtained for pool boiling shows enhancement in heat transfer for nanoparticle coated surface heater and compared with plain glass tube heater. Also heat transfer coefficient for nonuniformly coated nanoparticles was studied and compared with uniformly coated and plain glass tube. Coating effect of nanoparticles over glass tube increases its surface roughness and thereby creates more nucleation sites.

Pool Boiling of n-Pentane, CFC-113, and Water Under Reduced Gravity: Parabolic Flight Experiments With a Transparent Heater

1995 ◽  
Vol 117 (2) ◽  
pp. 408-417 ◽  
Author(s):  
T. Oka ◽  
Y. Abe ◽  
Y. H. Mori ◽  
A. Nagashima
Keyword(s):  
Heat Transfer ◽  
Parabolic Flight ◽  
Pool Boiling ◽  
Glass Plate ◽  
Nucleate Boiling ◽  
Heat Fluxes ◽  
Rear Side ◽  
Heater Surface ◽  
Reduced Gravity ◽  
Liquid Behavior

A series of pool boiling experiments have been conducted under reduced gravity condition (the order of 10−2 times the terrestrial gravity) available in an aircraft taking parabolic flight. A transparent resistant heater, a transparent indium oxide film plated on a glass plate, was employed so that the vapor/liquid behavior interacting with the heater surface could be observed from the rear side of the heater simultaneously with the side view of vapor bubbles above the heater surface. The experiments were performed for three different fluids—n-pentane, CFC-113, and water—under subcooled conditions. The critical heat fluxes for both n-pentane and CFC-113 under the reduced gravity were lowered to about 40 percent of the corresponding terrestrial values. Although the heat transfer characteristics in a low heat flux nucleate boiling regime for both n-pentane and CFC-113 showed no more than a slight change with the reduction in gravity, a significant heat transfer deterioration was noted with water in the reduced gravity boiling. The observation from the rear side of the heater suggested that this particular difference in the gravity dependency of heat transfer was ascribed to a considerable difference, between the organic fluids and water, in the behavior of attachment to the heater surface of the bubbles grown up, while the behavior of attachment must depend on the surface tension of each fluid and the wettability of the heater surface with the fluid.

Experimental Study of Enhanced Pool Boiling Heat Transfer Using Graphite Foam Inserts

2011 ◽  
Vol 312-315 ◽  
pp. 352-357 ◽  
Author(s):  
K.C. Leong ◽  
L.W. Jin ◽  
I. Pranoto ◽  
H.Y Li ◽  
J.C. Chai
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Boiling Heat Transfer ◽  
High Speed ◽  
Bubble Formation ◽  
Pool Boiling ◽  
Heat Fluxes ◽  
Copper Block ◽  
Different Types ◽  
Graphite Foam

This paper presents the results of an experimental study of heat transfer in a pool boiling evaporator with porous insert. Different types of graphite foams were tested with the phase change coolant FC-72 in a designed thermosyphon. Comparisons between the graphite foams and a solid copper block show that the porous structure enhances pool boiling significantly. The boiling thermal resistance of the tested graphite foams was found to be about 2 times lower than that of the copper block. The bubble formation recorded by a high speed camera indicates that boiling from a graphite foam is more vigorous than from a copper block. The designed thermosyphon with graphite foam insert can remove heat fluxes of up to 112 W/cm2 with the maximum heater temperature maintained below 100°C.

New Pool Boiling Heat Transfer in the Presence of Low-Frequency Vibrations Into a Vertical Cylindrical Heat Source

2014 ◽  
Vol 27 (5) ◽  
pp. 428-437 ◽  
Author(s):  
H. Atashi ◽  
A. Alaei ◽  
M. H. Kafshgari ◽  
R. Aeinehvand ◽  
S. K. Rahimi
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Low Frequency ◽  
Pool Boiling Heat Transfer

Laser Interferometric Investigation of the Microlayer Evaporation Phenomenon

1975 ◽  
Vol 97 (1) ◽  
pp. 88-92 ◽  
Author(s):  
C. M. Voutsinos ◽  
R. L. Judd
Keyword(s):  
Heat Transfer ◽  
High Speed ◽  
Laser Interferometry ◽  
Nucleate Boiling ◽  
High Speed Photography ◽  
Heater Surface ◽  
Nucleate Boiling Heat Transfer ◽  
Interferometric Investigation ◽  
Microlayer Evaporation ◽  
Laser Interferometric

An experimental investigation is presented in which the growth and evaporation of the microlayer underlying a bubble forming on a glass heater surface has been studied using laser interferometry and high speed photography. The results presented for a single bubble indicate that the microlayer thickness is of the order of 5 μm. Subsequent analysis of these results confirms that the microlayer evaporation phenomenon is a significant heat transfer mechanism, representing approximately 25 percent of the total nucleate boiling heat transfer rate for the conditions investigated.

Sign in / Sign up

Export Citation Format

Share Document