scholarly journals Discussion: “Inlet Shear Heating in Elastohydrodynamic Lubrication” (Greenwood, J. A., and Kauzlarich, J. J., 1973, ASME J. Lubr. Technol., 95, pp. 417–423)

1973 ◽  
Vol 95 (4) ◽  
pp. 423-425
Author(s):  
A. Dyson
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Shear Heating

scholarly journals Contributions of Molecular Dynamics Simulations to Elastohydrodynamic Lubrication

2021 ◽  
Vol 69 (1) ◽  
Author(s):  
James P. Ewen ◽  
Hugh A. Spikes ◽  
Daniele Dini
Keyword(s):  
Molecular Dynamics ◽  
Shear Rate ◽  
Experimental Design ◽  
Md Simulation ◽  
Elastohydrodynamic Lubrication ◽  
Quantitative Agreement ◽  
Coupling Methods ◽  
Fundamental Understanding ◽  
Shear Heating ◽  
Dynamics Simulations

AbstractThe prediction of friction under elastohydrodynamic lubrication (EHL) conditions remains one of the most important and controversial areas of tribology. This is mostly because the pressure and shear rate conditions inside EHL contacts are particularly severe, which complicates experimental design. Over the last decade, molecular dynamics (MD) simulation has played an increasingly significant role in our fundamental understanding of molecular behaviour under EHL conditions. In recent years, MD simulation has shown quantitative agreement with friction and viscosity results obtained experimentally, meaning that they can, either in isolation or through the use of multiscale coupling methods, begin to be used to test and inform macroscale models for EHL problems. This is particularly useful under conditions that are relevant inside machine components, but are difficult to obtain experimentally without uncontrollable shear heating.

On the Pressure Rippling and Roughness Deformation in Elastohydrodynamic Lubrication of Rough Surfaces

1993 ◽  
Vol 115 (3) ◽  
pp. 439-444 ◽  
Author(s):  
L. Chang ◽  
M. N. Webster ◽  
A. Jackson
Keyword(s):  
Surface Roughness ◽  
Rough Surface ◽  
Thermal Effects ◽  
Numerical Solutions ◽  
Elastohydrodynamic Lubrication ◽  
Shear Thinning ◽  
Isothermal Conditions ◽  
Large Pressure ◽  
Shear Heating ◽  
Micro Deformation

The objective of this paper is to conduct a qualitative analysis on the effects of lubricant shear thinning, lubricant shear heating and the roughness-induced transients on the pressure rippling and roughness deformation that occurs under elastohydrodynamic lubrication (EHL) conditions. To facilitate the analysis, the numerical solutions to an example problem of EHL line contact between a perfectly smooth surface and a sinusoidal rough surface are presented. This micro-EHL problem is first solved using the conventional model of a Newtonian lubricant and a stationary rough surface under isothermal conditions. It is then solved by including the non-Newtonian effects, the roughness-induced transients and the thermal effects in sequence, so that the changes in the results brought about by each of these elements can be clearly observed and then analyzed. The analysis, which is not limited to the model problem solved in this paper, suggests that misleading results of large pressure rippling and flattened surface roughness are obtained using the Newtonian lubricant models under steady-state, isothermal conditions. Much less micro-deformation of the surface roughness is actually produced because the magnitude of the pressure ripples is greatly limited by either the lubricant non-Newtonian shear thinning and shear heating or the roughness-induced transients.

Inlet Shear Heating in Elastohydrodynamic Lubrication

1973 ◽  
Vol 95 (4) ◽  
pp. 417-423 ◽  
Author(s):  
J. A. Greenwood ◽  
J. J. Kauzlarich
Keyword(s):  
Shear Rate ◽  
Theoretical Analysis ◽  
Film Thickness ◽  
Temperature Rise ◽  
Thermal Effects ◽  
Elastohydrodynamic Lubrication ◽  
Oil Film ◽  
Comparison With Experiment ◽  
Pure Rolling ◽  
Shear Heating

In EHL, the oil film thickness of rollers is controlled by the rate at which the oil is drawn into the conjunction of the disks by the moving surfaces of the rollers. The theory often assumes isothermal conditions in the inlet although it can be shown that the maximum shear rate often exceeds 106 sec−1, even in pure rolling. A theoretical analysis is presented for the oil temperature rise in the inlet of rollers, and the result is applied to predict the consequent film thickness. It is found that thermal effects on film thickness are only negligible at low rolling speeds. A comparison with experiment supports the conclusion that the thinning of the film thickness below that predicted by isothermal theory is substantially explained by inlet shear heating of the lubricant.

Plasto ‐elastohydrodynamic lubrication performance of greased ellipsoid contact

2021 ◽  
Author(s):  
Yong Zheng ◽  
Changqing Wang ◽  
Chao Pu ◽  
Jiayu Gong ◽  
Fanming Meng
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Lubrication Performance

Theoretical analysis of a rolling-sliding elastohydrodynamic lubrication line contact with a subsurface inclusion

2019 ◽  
Vol 233 (8) ◽  
pp. 1197-1207
Author(s):  
Armando Félix Quiñonez ◽  
Guillermo E Morales Espejel
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Element Model ◽  
Von Mises Stress ◽  
Transient Effects ◽  
Mean Velocity ◽  
The Matrix ◽  
Soft Inclusion ◽  
The Mean ◽  
Von Mises ◽  
Fully Coupled

This work investigates the transient effects of a single subsurface inclusion over the pressure, film thickness, and von Mises stress in a line elastohydrodynamic lubrication contact. Results are obtained with a fully-coupled finite element model for either a stiff or a soft inclusion moving at the speed of the surface. Two cases analyzed consider the inclusion moving either at the same speed as the mean velocity of the lubricant or moving slower. Two additional cases investigate reducing either the size of the inclusion or its stiffness differential with respect to the matrix. It is shown that the well-known two-wave elastohydrodynamic lubrication mechanism induced by surface features is also applicable to the inclusions. Also, that the effects of the inclusion become weaker both when its size is reduced and when its stiffness approaches that of the matrix. A direct comparison with predictions by the semi-analytical model of Morales-Espejel et al. ( Proc IMechE, Part J: J Engineering Tribology 2017; 231) shows reasonable qualitative agreement. Quantitatively some differences are observed which, after accounting for the semi-analytical model's simplicity, physical agreement, and computational efficiency, may then be considered as reasonable for engineering applications.

Sign in / Sign up

Export Citation Format

Share Document