Thermal Distortion of Spiral-Grooved Gas-Lubricated Thrust Bearings

1971 ◽  
Vol 93 (1) ◽  
pp. 102-111 ◽  
Author(s):  
C. Wachmann ◽  
S. B. Malanoski ◽  
J. H. Vohr
Keyword(s):  
Thrust Bearing ◽  
Load Capacity ◽  
Heat Removal ◽  
Maximum Load ◽  
Thermal Distortion ◽  
Thrust Bearings ◽  
Self Heating ◽  
Worked Example ◽  
Performance Curves

Self-heating during operation causes a bearing to undergo thermal distortion. A method is presented to determine the consequent effects on the load capacity of a spiral-grooved air-lubricated thrust bearing designed for maximum load capacity. The effect of mode of heat removal is discussed. Appropriate performance curves and a worked example are given.

Load Capacity Tests on Tapered-Land and Pivoted-Shoe Thrust Bearings for Large Steam-Turbine Application

1959 ◽  
Vol 81 (2) ◽  
pp. 208-213
Author(s):  
R. E. Brandon ◽  
H. C. Bahr
Keyword(s):  
Bearing Capacity ◽  
Steam Turbine ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Maximum Load ◽  
Full Scale ◽  
Thermal Distortion ◽  
Test Installation ◽  
Land Type ◽  
Thrust Bearings

Results of full-scale maximum load capacity tests on large, 3600-rpm, pivoted-shoe and tapered-land thrust bearings are reported. The results show 700 psi capacity for the pivoted-shoe bearing and 1085 psi for the tapered-land type. Additional evidence of thermal distortion and its effect on thrust-bearing capacity are discussed. A brief description of a new thrust-bearing test installation also is included.

An Accurate Solution of the Gas Lubricated, Flat Sector Thrust Bearing

1977 ◽  
Vol 99 (1) ◽  
pp. 82-88 ◽  
Author(s):  
I. Etsion ◽  
D. P. Fleming
Keyword(s):  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Thickness Distribution ◽  
Maximum Load ◽  
Accurate Solution ◽  
Operating Conditions ◽  
Thrust Bearings ◽  
Practical Design ◽  
Minimum Film Thickness

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

A hydrodynamic lubrication model and comparative analysis for coupled microgroove journal-thrust bearings lubricated with water

2019 ◽  
Vol 234 (11) ◽  
pp. 1755-1770
Author(s):  
Guo Xiang ◽  
Yanfeng Han ◽  
Renxiang Chen ◽  
Jiaxu Wang ◽  
Xiaokang Ni ◽  
...  
Keyword(s):  
Thrust Bearing ◽  
Hydrodynamic Lubrication ◽  
Load Capacity ◽  
Mutual Effect ◽  
Hydrodynamic Pressure ◽  
Isosceles Triangle ◽  
Maximum Load ◽  
Hydrodynamic Effect ◽  
Thrust Bearings ◽  
Lubrication Performance

The novelty of this study is to develop a hydrodynamic lubrication numerical model for coupled microgroove journal-thrust bearings (or coupled bearings) under water-lubricated condition. In the present model, the continuity of the hydrodynamic pressure and the fluid field (or coupled hydrodynamic effect) at common boundary is considered to reveal the mutual effect between the hydrodynamic behavior of the journal bearing and the thrust bearing. The lubrication performances of the coupled microgroove bearing with three bottom shapes, i.e., isosceles triangle, right triangle, and left triangle, are studied comparatively. Additionally, the effects of the microgroove depth on the lubrication performances of the coupled bearing are discussed. The present study reveals that the coupled hydrodynamic effect generated by the coupled bearing can improve the lubrication performance for both the journal and the thrust bearing. The microgroove with left triangle bottom shape yields the optimal lubrication performance as compared to the other two. There is an optimal groove depth that generates the maximum load capacity and the minimum friction coefficient for both the journal and the thrust bearing.

Thermal Distortion of Spiral-Grooved Gas-Lubricated Thrust Bearing Due to Self-Heating

1967 ◽  
Vol 89 (2) ◽  
pp. 197-202 ◽  
Author(s):  
C. H. T. Pan ◽  
B. Sternlicht
Keyword(s):  
Thrust Bearing ◽  
Load Capacity ◽  
Structural Materials ◽  
Fluid Film ◽  
Viscous Heating ◽  
Thermal Distortion ◽  
Simple Criterion ◽  
Numerical Example ◽  
Self Heating ◽  
Considerable Loss

The effects of thermal distortion due to viscous heating in the fluid film on the performance of a spiral-grooved, gas-lubricated thrust bearing are analyzed. A numerical example shows that considerable loss of load capacity is possible for bearings made of common structural materials. A simple criterion has been developed to check the importance of this type of thermal distortion.

Theoretical Study on Static Performance of Double-Bump Foil Bearings

2021 ◽  
Author(s):  
Fangcheng Xu ◽  
Jianhua Chu ◽  
Wenlin Luan ◽  
Guang Zhao
Keyword(s):  
Finite Element ◽  
Film Thickness ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Static Characteristics ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Static Performance ◽  
Initial Clearance

Abstract In this paper, single-bump foil models with different thickness and double-bump foil models with different initial clearances are established. The structural stiffness and equivalent viscous damping of double-bump foil and single-bump foil are analyzed by finite element simulation. The results show that the double-layer bump foil has variable stiffness and the displacement of the upper bump is greater than the initial gap when the two-layer bumps contact. A model for obtaining static characteristics of aerodynamic compliant foil thrust bearing is established on the basis of the stiffness characteristics of the double-bump foil. This paper solves gas Reynolds equation, the gas film thickness equation and the foil stiffness characteristic equation via the finite element method and the finite difference method. The static characteristics of the thrust bearings including the bearing pressure distribution, the gas film thickness and the friction power consumption have been obtained. The static characteristics of two kinds of foils have been compared and analyzed, and the effect of initial clearance on the static performance of double-bump foil bearings is studied. The results show that the double-bump foil structure can effectively improve the load capacity of thrust bearing. In addition, the static performance of double-bump foil thrust bearings is between the performance of the single-bump foil bearing and the double-bump foil bearing whose foil’s clearance is zero. The smaller the initial clearance is, the easier it will be to form a stable double-bump foil supporting structure.

Recent Improvements in Load Capacity of Large-Steam-Turbine Thrust Bearings

1961 ◽  
Vol 83 (1) ◽  
pp. 130-134 ◽  
Author(s):  
H. C. Bahr
Keyword(s):  
Thermal Conductivity ◽  
Steam Turbine ◽  
Load Capacity ◽  
Full Scale ◽  
High Thermal Conductivity ◽  
Thermal Distortion ◽  
Maximum Capacity ◽  
Thrust Bearings ◽  
Apparent Reduction

The load capacity of tapered-land and pivoted-shoe thrust bearings has been increased significantly by the use of materials with high thermal conductivity and by modified shoe designs. Results of full-scale maximum-capacity tests at 3600 rpm and at 1800 rpm are presented. Improvements in bearing performance have been made possible by an apparent reduction in thermal distortion and bearing temperature.

The Influence of Ambient Pressure on the Measured Load Capacity of Bump-Foil and Spiral-Groove Gas Thrust Bearings at Ambient Pressures up to 69 Bar on a Novel High-Pressure Gas Bearing Test Rig

2019 ◽  
Author(s):  
Jason Wilkes ◽  
Ryan Cater ◽  
Erik Swanson ◽  
Kevin Passmore ◽  
Jerry Brady
Keyword(s):  
Power Loss ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Ambient Pressure ◽  
Spiral Groove ◽  
Test Rig ◽  
Thrust Bearings ◽  
Order Of Magnitude ◽  
Foil Thrust Bearing ◽  
Thrust Load

Abstract This paper will show the influence of ambient pressure on the thrust capacity of bump-foil and spiral-groove gas thrust bearings. The bearings were operating in nitrogen at various pressures up to 69 bar, and were tested to failure. Failure was detected at various pressures by incrementally increasing the thrust load applied to the thrust bearing until the bearing was no longer thermally stable, or until contact was observed by a temperature spike measured by thermocouples within the bearing. These tests were performed on a novel thrust bearing test rig that was developed to allow thrust testing at pressures up to 207 bar cavity pressure at 260°C while rotating at speeds up to 120,000 rpm. The test rig floats on hydrostatic air bearings to allow for the direct measurement of applied thrust load through linkages that connect the stationary thrust loader to the rotor housing. Test results on a 65 mm (2.56 in) bump-foil thrust bearing at 100 krpm show a marked increase in load capacity with gas density, which has not previously been shown experimentally. Results also show that the load capacity of a similarly sized spiral-groove thrust bearing are relatively insensitive to pressure, and supported an order-of-magnitude less load than that observed for the bump-foil thrust bearing. These results are compared with analytical predictions, which agree reasonably with the experimental results. Predicted power loss is also presented for the bump-foil bearing; however, measured power loss was substantially higher.

Development of Foil Thrust Bearings with Simple Structure for Micro Turbines

2011 ◽  
Vol 368-373 ◽  
pp. 1392-1395 ◽  
Author(s):  
Quan Zhou ◽  
Yu Hou ◽  
Ru Gang Chen
Keyword(s):  
High Speed ◽  
Simple Structure ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Complicated Structure ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Rotational Systems ◽  
Micro Turbine ◽  
Foil Thrust Bearing

Because of the low power loss and high stability, foil bearings are suitable lubrication components for high speed rotational systems. At present, the foil bearings used in actual applications almost have complicated structure and are hard to manufacture. In this paper, two kinds of foil thrust bearings with simple structure are presented. Configurations of these two foil thrust bearings are introduced; meanwhile, the load capacity and running stability are also tested in a high speed micro turbine. It is shown that viscoelastic supported foil thrust bearing has higher load capacity and hemisphere convex dots supported foil thrust bearing is more stable in high speed operational condition.

Effects of Grooving in a Hydrostatic Circular Step Thrust Bearing With Porous Facing

2015 ◽  
Vol 137 (3) ◽  
Author(s):  
M. Mahbubur Razzaque ◽  
M. Zakir Hossain
Keyword(s):  
Mathematical Model ◽  
Inclination Angle ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Maximum Load ◽  
Seepage Flow ◽  
Groove Depth ◽  
Small Thickness ◽  
Flow Through ◽  
High Level

Effects of grooving in a porous faced hydrostatic circular step thrust bearing are investigated using a mathematical model based on the narrow groove theory (NGT). It is shown that enhancement of load capacity by grooving the step is possible at moderate level of permeability of the porous facing. Load capacity drops sharply with the increase of porous facing thickness. However, this drop in load capacity occurs mostly within a small thickness of the porous facing. Considering the coupled effects of permeability and inertia, it is recommended that the dimensionless step location should be 0.5–0.8 and the dimensionless step height should be less than five to take advantage of grooving. The groove geometric parameters such as groove inclination angle, fraction of grooved area and groove depth corresponding to the maximum load capacity are found to be the same for both with and without porous facing. However, with porous facing, the sensitivity of the load capacity on the groove parameters reduces. At high level of permeability, the effects of grooves may become insignificant because of high seepage flow through the porous facing.

Sign in / Sign up

Export Citation Format

Share Document