Heat Transfer to Evaporating Liquid Films

1971 ◽  
Vol 93 (4) ◽  
pp. 391-396 ◽  
Author(s):  
K. R. Chun ◽  
R. A. Seban
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Turbulent Flow ◽  
Transfer Coefficient ◽  
Liquid Films ◽  
Vertical Tube ◽  
Water Films ◽  
Laminar And Turbulent Flow ◽  
The Heat Transfer Coefficient

Results are presented for the heat-transfer coefficient for evaporation from the surface of water films flowing along the outside surface of a vertical tube for the cases of laminar and turbulent flow. Correspondence with results for condensation and liquid heating is shown and the transition from laminar to turbulent flow is indicated to depend on quantities other than Reynolds number.

The Simulation Study of Turbulence Models for Conjugate Heat Transfer Analysis of a High Pressure Air-Cooled Gas Turbine

2010 ◽  
Author(s):  
Zhenfeng Wang ◽  
Peigang Yan ◽  
Hongfei Tang ◽  
Hongyan Huang ◽  
Wanjin Han
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbine ◽  
Turbulence Model ◽  
Conjugate Heat Transfer ◽  
Turbulence Models ◽  
Turbulence Characteristic ◽  
The Heat Transfer Coefficient

The different turbulence models are adopted to simulate NASA-MarkII high pressure air-cooled gas turbine. The experimental work condition is Run 5411. The paper researches that the effect of different turbulence models for the flow and heat transfer characteristics of turbine. The turbulence models include: the laminar turbulence model, high Reynolds number k-ε turbulence model, low Reynolds number turbulence model (k-ω standard format, k-ω-SST and k-ω-SST-γ-θ) and B-L algebra turbulence model which is adopted by the compiled code. The results show that the different turbulence models can give good flow characteristics results of turbine, but the heat transfer characteristics results are different. Comparing to the experimental results, k-ω-SST-θ-γ turbulence model results are more accurate and can simulate accurately the flow and heat transfer characteristics of turbine with transition flow characteristics. But k-ω-SST-γ-θ turbulence model overestimates the turbulence kinetic energy of blade local region and makes the heat transfer coefficient higher. It causes that local region temperature is higher. The results of B-L algebra turbulence model show that the results of B-L model are accurate besides it has 4% temperature error in the transition region. As to the other turbulence models, the results show that all turbulence models can simulate the temperature distribution on the blade pressure surface except the laminar turbulence model underestimates the heat transfer coefficient of turbulence flow region. On the blade suction surface with transition flow characteristics, high Reynolds number k-ε turbulence model overestimates the heat transfer coefficient and causes the blade surface temperature is high about 90K than the experimental result. Low Reynolds number k-ω standard format and k-ω-SST turbulence models also overestimate the blade surface temperature value. So it can draw a conclusion that the unreasonable choice of turbulence models can cause biggish errors for conjugate heat transfer problem of turbine. The combination of k-ω-SST-γ-θ model and B-L algebra model can get more accurate turbine thermal environment results. In addition, in order to obtain the affect of different turbulence models for gas turbine conjugate heat transfer problem. The different turbulence models are adopted to simulate the different computation mesh domains (First case and Second case). As to each cooling passages, the first case gives the wall heat transfer coefficient of each cooling passages and the second case considers the conjugate heat transfer course between the cooling passages and blade. It can draw a conclusion that the application of heat transfer coefficient on the wall of each cooling passages avoids the accumulative error. So, for the turbine vane geometry models with complex cooling passages or holes, the choice of turbulence models and the analysis of different mesh domains are important. At last, different turbulence characteristic boundary conditions of turbine inner-cooling passages are given and K-ω-SST-γ-θ turbulence model is adopted in order to obtain the effect of turbulence characteristic boundary conditions for the conjugate heat transfer computation results. The results show that the turbulence characteristic boundary conditions of turbine inner-cooling passages have a great effect on the conjugate heat transfer results of high pressure gas turbine.

Experimental Investigation of Air–Water Mist Jet Impingement Cooling Over a Heated Cylinder

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Chunkyraj Khangembam ◽  
Dushyant Singh
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Stagnation Point ◽  
Jet Impingement ◽  
Water Mist ◽  
Heated Cylinder ◽  
Air Jet ◽  
The Heat Transfer Coefficient

Experimental investigation on heat transfer mechanism of air–water mist jet impingement cooling on a heated cylinder is presented. The target cylinder was electrically heated and was maintained under the boiling temperature of water. Parametric studies were carried out for four different values of mist loading fractions, Reynolds numbers, and nozzle-to-surface spacings. Reynolds number, Rehyd, defined based on the hydraulic diameter, was varied from 8820 to 17,106; mist loading fraction, f ranges from 0.25% to 1.0%; and nozzle-to-surface spacing, H/d was varied from 30 to 60. The increment in the heat transfer coefficient with respect to air-jet impingement is presented along with variation in the heat transfer coefficient along the axial and circumferential direction. It is observed that the increase in mist loading greatly increases the heat transfer rate. Increment in the heat transfer coefficient at the stagnation point is found to be 185%, 234%, 272%, and 312% for mist loading fraction 0.25%, 0.50%, 0.75%, and 1.0%, respectively. Experimental study shows identical increment in stagnation point heat transfer coefficient with increasing Reynolds number, with lowest Reynolds number yielding highest increment. Stagnation point heat transfer coefficient increased 263%, 259%, 241%, and 241% as compared to air-jet impingement for Reynolds number 8820, 11,493, 14,166, and 17,106, respectively. The increment in the heat transfer coefficient is observed with a decrease in nozzle-to-surface spacing. Stagnation point heat transfer coefficient increased 282%, 248%, 239%, and 232% as compared to air-jet impingement for nozzle-to-surface spacing of 30, 40, 50, and 60, respectively, is obtained from the experimental analysis. Based on the experimental results, a correlation for stagnation point heat transfer coefficient increment is also proposed.

scholarly journals CFD-Entropy generation analysis of refrigerant-based nanofluids flow in a tube

2020 ◽  
Vol 307 ◽  
pp. 01038
Author(s):  
Mohammed Zohud ◽  
Ahmed Ouadha ◽  
Redouane Benzeguir
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Entropy Generation ◽  
Constant Heat Flux ◽  
Flux Boundary Condition ◽  
Flow Heat ◽  
Heat Flux Boundary Condition ◽  
The Heat Transfer Coefficient

The present paper aims to numerically investigate the flow, heat transfer and entropy generation of some hydrocarbon based nanorefrigerants flowing in a circular tube subject to constant heat flux boundary condition. Numerical tests have been performed for 4 types of nanoparticles, namely Al2O3, CuO, SiO2, and ZnO with a diameter equal to 30 nm and a volume concentration of φ = 5%. These nanoparticles are dispersed in some hydrocarbon-based refrigerants, namely tetrafluoroethane (R134a), propane (R290), butane (R600), isobutane (R600a) and propylene (R1270). Computations have been performed for Reynolds number ranging from 600 to 2200. The numerical results in terms of the average heat transfer coefficient of pure refrigerants have been compared to values obtained using correlations from the literature. The results show that the increase of the Reynolds number increases the heat transfer coefficient and decreases the total entropy generation.

Study on Heat Transfer and Flow Behavior of Mini-Tube Bank for Micro Heat Exchanger

2006 ◽  
Author(s):  
Y. Koizumi ◽  
T. Okuyama ◽  
H. Ohtake
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Flow Behavior ◽  
Flow State ◽  
Wake Region ◽  
Tube Bank ◽  
Disturbed Condition ◽  
The Heat Transfer Coefficient

Heat transfer and flow behavior in the mini tube bank were examined. The tube bank was composed of 1 mm diameter nickel wires and a 30 mm wide × 15 mm high flow channel. Experiments were performed in the range of the rod Re = 5 ~ 430 by using water. Numerical analyses were also conducted with the commercial CFD code STAR-CD. The heat transfer coefficient after the second row was lower than first row's one. The flow visualization results indicated that the wake region was stagnant when the Reynolds number was low. This flow stagnation seemed to cause the heat transfer coefficient deterioration in the tube bank. As the Reynolds number was increased, the flow state in the wake region gradually changed from the stagnant condition to the more disturbed condition. The deeper the row was, the more disturbed the wake was. The heat transfer coefficient began to recover to the first row value at certain Reynolds number. The recovery started from the most downstream row; fifth row in the present experiments and was propagated to the upstream row. The Reynolds number when the recovery was initiated decreased as the spacing between rods was increased. The analytical results of the STAR-CD code supported the experimental results. When the wake was stagnant, the heat transfer coefficient distribution around the rear rod, i.e. the rod in the wake, showed a large dip in the front region of the rod. It was considered that this dip caused the heat transfer coefficient decrease after the second row observed in the experiments.

Experimental and CFD Investigations of Heat Transfer in Helical Coils for the Development of Correlations for Newtonian and Non-Newtonian Fluids in Transient State-Space Conditions

2013 ◽  
Author(s):  
Sandipan S. Pawar ◽  
Vivek K. Sunnapwar ◽  
Vivek K. Yakkundi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Turbulent Flow ◽  
Transfer Coefficient ◽  
Flow Regimes ◽  
Newtonian Fluids ◽  
Water Mixture ◽  
Glycerol Water ◽  
Laminar And Turbulent Flow ◽  
Helical Coils

Experimental studies and CFD investigations were carried out under laminar and turbulent flow regimes in isothermal steady state and non-isothermal unsteady state conditions in helical coils for Newtonian and non-Newtonian fluids. Water and glycerol-water mixture (10 and 20 % glycerol) as Newtonian fluids and dilute aqueous polymer solutions of sodium carboxymethyl cellulose (SCMC), sodium alginate (SA) as non-Newtonian fluids were used in this study. The experiments were performed for three helical coils of coil curvature ratios as 0.0757, 0.064 and 0.055 in laminar and turbulent flow regimes. For the first time, two innovative correlations to calculate Nusselt number (Nu) in terms of new dimensionless ‘M’ number, Prandtl number and coil curvature ratio under different conditions for Newtonian fluids are proposed in this paper. Third correlation of Nu vs. Graetz number (Gz) including the effects of coil curvature on heat transfer coefficient which was not considered by earlier investigators is developed based on tests conducted in laminar flow for Newtonian fluids. All these three innovative correlations developed based on experimental data which were not found in the literature. These correlations were compared with the work of earlier investigators and were found to be in good agreement. The CFD analysis for laminar and turbulent flow was carried out using the CFD package FLUENT 12.0.16. The CFD calculation results (Nui, U) for laminar and turbulent flows were compared with the experimental results, and also the work of earlier investigators was found to be in excellent agreement. Further, the effect of helix diameter on heat transfer for Newtonian and Non-Newtonian fluids are also presented in this paper and it was observed that as helix diameter increases, overall heat transfer coefficient decreases.

Wind-Related Heat Transfer Coefficient for Flat-Plate Solar Collectors

1987 ◽  
Vol 109 (2) ◽  
pp. 108-110 ◽  
Author(s):  
S. Shakerin
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Flat Plate ◽  
Separation Bubble ◽  
Convective Heat Transfer Coefficient ◽  
Leading Edge ◽  
The Heat Transfer Coefficient ◽  
Good Agreement

Experiments were performed to evaluate the convective heat transfer coefficient for a flat plate mounted in a wooden model of a roof of a building. The experiments were carried out in a closed-circuit wind tunnel and included parametric adjustments of the roof tilt and Reynolds number, based on the length of the plate. The roof tilt was set at 0, 30, 45, 60, and 90 degrees and the Reynolds number ranged from 58,000 to 250,000. A transient, one lump, thermal approach was used for heat transfer calculations. Due to a separation bubble at the leading edge of the model, i.e., the roof, at angles of attack of less than 40 degrees, the flow became turbulent after reattachment. This resulted in a higher heat transfer than previously reported in the literature. At higher angles of attack, the flow was not separated at the leading edge and remained laminar. The heat transfer coefficient for higher angles of attack, i.e., α > 40 deg, was found to be approximately independent of the angle of attack and in good agreement with the previously published results.

Applied Pulsed Flow for Single-Phase Convective Heat Transfer Enhancement in a Laminar Flow Cooling System

2008 ◽  
Author(s):  
Bolaji O. Olayiwola ◽  
Gerhard Schaldach ◽  
Peter Walzel
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Cooling System ◽  
Transfer Enhancement ◽  
Flow Rates ◽  
The Heat Transfer Coefficient

Experimental and CFD studies were performed to investigate the enhancement of convective heat transfer in a laminar cooling system using flow pulsation in a flat channel with series of regular spaced fins. Glycerol-water mixtures with dynamic viscosities in the range of 0.001 kg/ms–0.01 kg/ms were used. A steady flow Reynolds number in the laminar range of 10 < Re < 1200 was studied. The amplitudes of the applied pulsations are in the range of 0.25 < A < 0.55 mm and the frequency range is 10 < f < 60 Hz. Two different cooling devices with active length L = 450 mm and 900 mm were investigated. CFD simulations were performed on a parallel-computer (Linux-cluster) using the software suit CFX11 from ANSYS GmbH, Germany. The rate of cooling was found to be significant at moderate low net flow rates. In general, no significant heat transfer enhancement at very low and high flow rates was obtained in compliance with the experimental data. The heat transfer coefficient was found to increase with increasing Prandtl number Pr at constant oscillation Reynolds number Reosc whereas the ratio of the hydraulic diameter to the length of the channel dh/L has insignificant effect on the heat transfer coefficient. This is due to enhanced fluid mixing. CFD results allow for performance predictions of different geometries and flow conditions.

scholarly journals Intensified Thermal Conductivity and Convective Heat Transfer of Ultrasonically Prepared CuO–Polyaniline Nanocomposite Based Nanofluids in Helical Coil Heat Exchanger

2019 ◽  
Vol 64 (2) ◽  
pp. 271-282 ◽  
Author(s):  
Abhishek Lanjewar ◽  
Bharat Bhanvase ◽  
Divya Barai ◽  
Shivani Chawhan ◽  
Shirish Sonawane
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Base Fluid ◽  
Cuo Nanoparticles ◽  
The Heat Transfer Coefficient

In this study, investigation of convective heat transfer enhancement with the use of CuO–Polyaniline (CuO–PANI) nanocomposite basednanofluid inside vertical helically coiled tube heat exchanger was carried out experimentally. In these experiments, the effects of different parameters such as Reynolds number and volume % of CuO–PANI nanocomposite in nanofluid on the heat transfer coefficient of base fluid have been studied. In order to study the effect of CuO–PANI nanocomposite based nanofluid on heat transfer, CuO nanoparticles loaded in PANI were synthesized in the presence of ultrasound assisted environment at different loading concentration of CuO nanoparticles (1, 3 and 5 wt.%). Then the nanofluids were prepared at different concentrations of CuO–PANI nanocomposite using water as a base fluid. The 1 wt.% CuO–PANI nanocomposite was selected for the heat transfer study for nanofluid concentration in the range of 0.05 to 0.3 volume % and Reynolds number range of was 1080 to 2160 (±5). Around 37 % enhancement in the heat transfer coefficient was observed for 0.2 volume % of 1 wt.% CuO–PANI nanocomposite in the base fluid. In addition, significant enhancement in the heat transfer coefficient was observed with an increase in the Reynolds number and percentage loading of CuO nanoparticle in Polyaniline (PANI).

The Effect of Density Variation on Heat Transfer in the Critical Region

1961 ◽  
Vol 83 (2) ◽  
pp. 176-181 ◽  
Author(s):  
Yih-Yun Hsu ◽  
J. M. Smith
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Transfer Coefficient ◽  
Natural Convection ◽  
Turbulent Flow ◽  
Transfer Coefficient ◽  
Critical Point ◽  
Critical Region ◽  
Large Density ◽  
The Heat Transfer Coefficient

The heat-transfer coefficient between fluid and tube wall in turbulent flow depends upon the physical and thermal properties of the fluid. When density changes across the diameter of the tube are large (for example, when the fluid is near the critical point), the variable density can affect the transfer of momentum and heat. Equations are developed for predicting the magnitude of this effect on the heat-transfer coefficient. Deissler’s [5] expressions for the eddy diffusivity are employed in solving the equations for heat and momentum transfer. For flow in vertical tubes large density variations can also affect the heat transfer by inducing natural convection. By considering the influence of body forces on the shear stress, equations are derived to predict the effect of natural convection on the heat-transfer coefficient for turbulent flow. The results indicate that the effect is significant only for relatively high Grashof numbers and low Reynolds numbers. Such conditions may be encountered in flow of a fluid near its thermodynamic critical point. The derived equations are applied for carbon dioxide flow in the critical region under the conditions for which experimental data were measured by Bringer and Smith [2]. Because of the high Reynolds and low Grashof numbers, natural convection is not significant. However, the effect of the large density variations is found to be significant, and the predicted results agree well with the experimental data.

Sign in / Sign up

Export Citation Format

Share Document