Flow Induced Vibrations of a Hydraulic Valve and Their Elimination

1978 ◽  
Vol 100 (2) ◽  
pp. 239-245 ◽  
Author(s):  
D. S. Weaver ◽  
F. A. Adubi ◽  
N. Kouwen
Keyword(s):  
Check Valve ◽  
Rate Of Change ◽  
High Rate ◽  
Fluid Inertia ◽  
Dimensional Model ◽  
Flow Control Devices ◽  
Flow Induced Vibrations ◽  
Valve Opening ◽  
Control Devices ◽  
Hydraulic Valve

The flow induced vibrations of a check valve with a spring damper to prevent slamming have been studied experimentally. Both prototype and two-dimensional model experiments were conducted to develop an understanding of the mechanism of self-excitation. The phenomenon is shown to be caused by the high rate of change of discharge at small angles of valve opening and the hysteretic hydrodynamic loading resulting from fluid inertia. As the discharge-displacement characteristics of the valve are dependent on its geometry, modifications of this geometry were examined and one found which eliminated the vibrations entirely. The phenomenon studied is considered to be the same as that causing vibrations in numerous other flow control devices when operating at small openings.

A Theoretical Model for Self-Excited Vibrations in Hydraulic Gates, Valves and Seals

1980 ◽  
Vol 102 (2) ◽  
pp. 146-151 ◽  
Author(s):  
D. S. Weaver ◽  
S. Ziada
Keyword(s):  
Theoretical Model ◽  
Discharge Coefficient ◽  
Nonlinear Differential Equations ◽  
Check Valve ◽  
Structural Stiffness ◽  
Fluid Inertia ◽  
Vibration Displacement ◽  
Runge Kutta Method ◽  
Flow Control Devices ◽  
Control Devices

A general theoretical model is presented for the jet flow mechanism of self-excited vibrations of flow control devices operating at small openings. The coupled nonlinear differential equations are solved numerically using the Runge-Kutta method. The vibration displacement and discharge characteristics are given for a variety of parameters such as structural stiffness, fluid inertia and discharge coefficient. The predictions are shown to agree reasonably well with the experimental observations of swing check valve vibrations.

scholarly journals New Insight on Liquid Steel Microalloying by Pulse-Step Method in Two-Strand Slab Tundish by Numerical Simulations

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 448
Author(s):  
Adam Cwudziński
Keyword(s):  
Liquid Steel ◽  
Mixing Time ◽  
Casting Process ◽  
Step Method ◽  
Flow Control Devices ◽  
Alloy Addition ◽  
Interesting Approach ◽  
Control Devices ◽  
Steel Flow ◽  
Alloy Concentration

Developing a technology for introducing alloy addition to liquid steel during the course of continuous casting process seems to be an interesting approach to enhancing the steelmaking process, especially as the effective introduction of micro-additives or non-metallic inclusion modifiers to the liquid steel is the key to the production of the highest-quality steel. This paper presents the results of investigation describing the process of liquid steel chemical homogenisation in the two-strand slab tundish. The alloy was fed to liquid steel by pulse-step method. Five tundish equipment variants with different flow control devices and alloy addition feeding positions were considered. The paper includes fields of liquid steel flow, alloy concentration vs. time curves, dimensionless mixing time, minimum time values and alloy concentration deviations at tundish outlets. The results pointed much more effectively with liquid steel mixing nickel than aluminium. For aluminium obtaining a 95% chemical homogenisation level requires three-fold more time. Moreover, it is definitely beneficial for chemical homogenisation to initiate the alloying process simultaneously in two sites. This procedure generates, among others, the least alloy deviation of concentration at tundish outlets.

scholarly journals Insulation Life Span of Low-Voltage Electric Motors—A Survey

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1738
Author(s):  
Vanessa Neves Höpner ◽  
Volmir Eugênio Wilhelm
Keyword(s):  
Life Span ◽  
Electric Motor ◽  
Low Voltage ◽  
Frequency Converter ◽  
Rate Of Change ◽  
High Rate ◽  
Switching Frequency ◽  
Electric Motors ◽  
Frequency Converters ◽  
High Switching Frequency

The use of static frequency converters, which have a high switching frequency, generates voltage pulses with a high rate of change over time. In combination with cable and motor impedance, this generates repetitive overvoltage at the motor terminals, influencing the occurrence of partial discharges between conductors, causing degradation of the insulation of electric motors. Understanding the effects resulting from the frequency converter–electric motor interaction is essential for developing and implementing insulation systems with characteristics that support the most diverse applications, have an operating life under economically viable conditions, and promote energy efficiency. With this objective, a search was carried out in three recognized databases. Duplicate articles were eliminated, resulting in 1069 articles, which were systematically categorized and reviewed, resulting in 481 articles discussing the causes of degradation in the insulation of electric motors powered by frequency converters. A bibliographic portfolio was built and evaluated, with 230 articles that present results on the factors that can be used in estimating the life span of electric motor insulation. In this structure, the historical evolution of the collected information, the authors who conducted the most research on the theme, and the relevance of the knowledge presented in the works were considered.

Soft Switching Approach to Reducing Transition Losses in an On/Off Hydraulic Valve

2009 ◽  
Author(s):  
Michael B. Rannow ◽  
Perry Y. Li
Keyword(s):  
Hydraulic System ◽  
Check Valve ◽  
Fluid Flows ◽  
Soft Switching ◽  
Total System ◽  
System Efficiency ◽  
Hydraulic Systems ◽  
Controlled Systems ◽  
Flow Through ◽  
Hydraulic Valve

A method for significantly reducing the losses associated with an on/off controlled hydraulic system is proposed. There has been a growing interest in the use of on/off valves to control hydraulic systems as a means of improving system efficiency. While on/off valves are efficient when they are fully open or fully closed, a significant amount of energy can be lost in throttling as the valve transitions between the two states. A soft switching approach is proposed as a method of eliminating the majority of these transition losses. The operating principle of soft switching is that fluid can temporarily flow through a check valve or into a small chamber while valve orifices are partially closed. The fluid can then flow out of the chamber once the valve has fully transitioned. Thus, fluid flows through the valve only when it is in its most efficient fully open state. A model of the system is derived and simulated, with results indicating that the soft switching approach can reduce transition and compressibility losses by 79%, and total system losses by 66%. Design equations are also derived. The soft switching approach has the potential to improve the efficiency of on/off controlled systems and is particularly important as switching frequencies are increased. The soft switching approach will also facilitate the use of slower on/off valves for effective on/off control; in simulation, a valve with soft switching matched the efficiency an on/off valve that was 5 times faster.

scholarly journals Prediction of flow-control devices' noise with modified acoustic perturbation equations

2020 ◽  
Vol 22 (3) ◽  
pp. 619-627
Author(s):  
Luca Fenini ◽  
Stefano Malavasi
Keyword(s):  
Flow Control ◽  
Fluid Dynamic ◽  
International Standards ◽  
The Other ◽  
Computational Time ◽  
Noise Prediction ◽  
Acoustic Perturbation ◽  
Flow Control Devices ◽  
Control Devices ◽  
Perturbation Equations

Abstract Fluid-dynamic noise emissions produced by flow-control devices inside ducts are a concerning issue for valve manufacturers and pipeline management. This work proposes a modified formulation of Acoustic Perturbation Equations (APE) that is applicable to industrial frameworks where the interest is addressed to noise prediction according to international standards. This formulation is derived from a literature APE system removing two terms allowing for a computational time reduction of about 20%. The physical contribution of the removed terms is discussed according to the literature. The modified APE are applied to the prediction of the noise emitted by an orifice. The reliability of the new APE system is evaluated by comparing the Sound Pressure Level (SPL) and the acoustic pressure with the ones returned by LES and literature APE. The new formulation agrees with the other methods far from the orifice: moving over nine diameters downstream of the trailing edge, the SPL is in accordance with the other models. Since international standards characterize control devices with the noise measured 1 m downstream of them, the modified APE formulation provides reliable and faster noise prediction for those devices with outlet diameter, d, such that 9d < 1 m.

scholarly journals Development and evaluation of the focused assessment of sonographic pathologies in the intensive care unit (FASP-ICU) protocol

Critical Care ◽  
2021 ◽  
Vol 25 (1) ◽  
Author(s):  
Stefan Schmidt ◽  
Jana-Katharina Dieks ◽  
Michael Quintel ◽  
Onnen Moerer
Keyword(s):  
Intensive Care Unit ◽  
Intensive Care ◽  
Conclusive Evidence ◽  
Rate Of Change ◽  
University Hospital ◽  
High Rate ◽  
Whole Body ◽  
Routine Surveillance ◽  
Organ Systems ◽  
Training Schemes

Abstract Background The use of ultrasonography in the intensive care unit (ICU) is steadily increasing but is usually restricted to examinations of single organs or organ systems. In this study, we combine the ultrasound approaches the most relevant to ICU to design a whole-body ultrasound (WBU) protocol. Recommendations and training schemes for WBU are sparse and lack conclusive evidence. Our aim was therefore to define the range and prevalence of abnormalities detectable by WBU to develop a simple and fast bedside examination protocol, and to evaluate the value of routine surveillance WBU in ICU patients. Methods A protocol for focused assessments of sonographic abnormalities of the ocular, vascular, pulmonary, cardiac and abdominal systems was developed to evaluate 99 predefined sonographic entities on the day of admission and on days 3, 6, 10 and 15 of the ICU admission. The study was a clinical prospective single-center trial in 111 consecutive patients admitted to the surgical ICUs of a tertiary university hospital. Results A total of 3003 abnormalities demonstrable by sonography were detected in 1275 individual scans of organ systems and 4395 individual single-organ examinations. The rate of previously undetected abnormalities ranged from 6.4 ± 4.2 on the day of admission to 2.9 ± 1.8 on day 15. Based on the sonographic findings, intensive care therapy was altered following 45.1% of examinations. Mean examination time was 18.7 ± 3.2 min, or 1.6 invested minutes per detected abnormality. Conclusions Performing the WBU protocol led to therapy changes in 45.1% of the time. Detected sonographic abnormalities showed a high rate of change in the course of the serial assessments, underlining the value of routine ultrasound examinations in the ICU. Trial registration The study was registered in the German Clinical Trials Register (DRKS, 7 April 2017; retrospectively registered) under the identifier DRKS00010428.

The Application of Shape Memory Alloy as Vortex Generators and Flow Control Devices for Enhanced Convective Heat Transfer

2007 ◽  
Author(s):  
Mohd. S. Aris ◽  
Ieuan Owen ◽  
Chris. J. Sutcliffe
Keyword(s):  
Heat Transfer ◽  
Flow Control ◽  
Shape Memory ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Convective Heat ◽  
Vortex Generators ◽  
Transfer Enhancement ◽  
Flow Control Devices ◽  
Control Devices

This paper is concerned with convective heat transfer enhancement of heated surfaces through the use of vortex generators and flow control devices. A preliminary proof-of-concept investigation has been carried out into the use of active vortex generators and flow control elements, both manufactured from Shape Memory Alloys (SMAs) which are activated at set temperatures. The vortex generators change their shape to intrude further into the flow at high temperature to enhance heat transfer, while they maintain a low profile at low temperatures to minimise flow pressure losses. One set of vortex generators was made from pre-alloyed powders of SMA material in an advanced rapid prototyping process known as Selective Laser Melting (SLM). Another set of devices was also made from commercially available flat annealed thin SMA sheets for comparison purposes. The flow control elements are devices that preferentially guide the flow to heated parts of a surface, again using temperature-activated SMAs. Promising results were obtained for both the vortex generator and flow control device when their temperatures were varied from 20° to 85°C. The vortex generators responded by increasing their angle of attack from 20° to 35° while the wavy flow control elements straightened out at higher temperatures. As the designs were two-way trained, they regain their initial position and shape at a lower temperature. The surface temperature of the heated plate on which the active devices were positioned reduced between 8 to 51%, indicating heat transfer enhancement due to the generated vortices and changes in air flow rates.

Sign in / Sign up

Export Citation Format

Share Document