Flow Control in Wide-Angled Conical Diffusers

1976 ◽  
Vol 98 (4) ◽  
pp. 728-735 ◽  
Author(s):  
M. C. Welsh
Keyword(s):  
Flow Control ◽  
Control Device ◽  
Performance Characteristics ◽  
Flow Conditions ◽  
Mean Velocity ◽  
Inlet Condition ◽  
Control Techniques ◽  
Flow Control Device ◽  
Conical Diffuser ◽  
Two Factors

Flow control techniques in wide-angled conical diffusers are discussed. Selected performance characteristics of a wide-angled conical diffuser and tailpipe with and without a star flow-control device are also presented. The diffuser performance is sensitive to the star location and geometry and to the diffuser inlet flow conditions. The correct combination of the first two factors for a given inlet condition leads to a significant increase in pressure recovery and flow stability in the diffuser and tailpipe, together with satisfactory mean velocity profiles for entry to downstream duct components.

Sound suppressing gas flow control device

1980 ◽  
Vol 67 (4) ◽  
pp. 1413-1413
Author(s):  
George J. Kay ◽  
Alan Keskimen
Keyword(s):  
Flow Control ◽  
Gas Flow ◽  
Control Device ◽  
Flow Control Device

The Development of a Pressure Actuated Isolation Nozzle Assembly and its Application as Flow Control Device in Extended Reach Water-Alternating-Gas Pilot Wells

2021 ◽  
Author(s):  
Zhihua Wang ◽  
Aqib Qureshi ◽  
Tarik A Abdelfattah ◽  
Joshua R Snitkoff
Keyword(s):  
Flow Control ◽  
Drilling Fluid ◽  
Applied Pressure ◽  
Control Device ◽  
Lessons Learned ◽  
Production Performance ◽  
Dissolution Time ◽  
Enhanced Production ◽  
Water Alternating Gas ◽  
Flow Control Device

Abstract The re-development of a giant offshore field in the United Arab Emirates (UAE) consists predominantly of four artificial islands requiring in most cases extremely long horizontal laterals to reach the reservoir targets. Earlier SPE technical papers (1,2) have introduced the development, testing, qualification, and deployment of the plugged liner technology using the dissolvable plugged nozzles (DPNs). The use of DPN plugged liner technology has resulted in CAPEX savings and enhanced production performance. The benefits of DPN technology are its simplicity along with its cost effectiveness. However, the dissolvable material has some limitations, such as pressure rating and dissolution time, which are fluid chemistry dependent. To overcome these limits, a new Pressure Actuated Isolation Nozzle Assembly (PAINA) was developed as an alternative to the plugged liner tool for applications where a higher pressure rating is required, as well as on demand opening. Furthermore, the new PAINA also functions as a flow control device during injection and production, enhancing acid jetting effects during bullhead stimulation and reducing brine losses during liner installation. Liners with PAINAs can be run to TD similar to blank pipe: fluids can be circulated through the inside of the liner without the need for a wash pipe. Once on bottom, non-aqueous drilling fluid is displaced to brine without actuating the isolation mechanism. When the well is ready for production or injection, pressure is applied and the isolation mechanism is activated to establish communication between well and reservoir. These tools were successfully run as flow control devices in water-alternating-gas (WAG) pilot wells. The planning and execution of the initial application will be discussed, along with the tool development, qualification testing, and lessons learned. The key advantage of this technology is in extending plugged liner applications to cases where other pressure-operated tools are included as part of the liner lower completion. Pressure can be applied to the well multiple times without activating the isolation mechanism as long as the applied pressure is below the actuation pressure.

Investigation of a Passive Flow Control Device in an S-Duct Inlet of a Propulsion System With High Subsonic Flow

2018 ◽  
Author(s):  
Asad Asghar ◽  
Satpreet Sidhu ◽  
William D. E. Allan ◽  
Grant Ingram ◽  
Tom M. Hickling ◽  
...  
Keyword(s):  
Flow Control ◽  
Complex Geometry ◽  
Control Device ◽  
Pressure Recovery ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Flow Control Device ◽  
Inner Radius ◽  
Selection Of ◽  
Numerical Approaches

S-Ducts have wide application on air vehicles with embedded engines. The complex geometry is known to lead to separation downstream of curved profiles. This paper reports the influences on that flow of passive flow control geometries. In these experiments, stream-wise tubercles were applied in an effort to improve the internal performance of S-duct diffusers, parameters including pressure recovery, distortion and swirl. The test articles were tested with the high subsonic (Ma = 0.8) flow and were manufactured using 3D printing. Stream-wise static pressure and exit-plane total pressure were measured in a test rig using surface pressure taps and a 5-probe rotating rake, respectively; the baseline and variant S-ducts were simulated through computational fluid dynamics. The experiments showed that some subtle improvements to the S-Duct distortion could be achieved through careful selection of tubercle geometry. Generally, the recovered flow downstream of the inner radius of the second bend of the S-duct deteriorated, but overall pressure recovery improved. The simulations were useful in characterizing swirl, whereas experiments were not so equipped. Adjustments to the numerical approaches resulted in reasonable agreement with the experiments.

Sign in / Sign up

Export Citation Format

Share Document