Water Production from Exhaust Gases of Steam Power Plants

1979 ◽  
Vol 101 (4) ◽  
pp. 677-679
Author(s):  
N. Papageorgiou
Keyword(s):  
Natural Gas ◽  
Power Plants ◽  
Water Production ◽  
Economic Aspects ◽  
Steam Generators ◽  
Steam Power ◽  
Power Cycles ◽  
Exhaust Gases ◽  
Steam Power Plants ◽  
Nontraditional Method

An attractive and nontraditional method for water production is presented in this paper. The proposed method is to condense the exhaust gases of the natural gas fired steam generators of power plants. In order to achieve this, it is necessary that modification of the convectional steam power cycles be accomplished without sacrificing the efficiency of the power plants. An investigation and modification of the power cycles is proposed. Economic aspects are also considered.

scholarly journals Internal Combustion Steam Cycle (G.I.S.T. Cycle): Thermodynamical Feasibility and Plant Lay-Out Proposals

1997 ◽  
Author(s):  
C. Caputo ◽  
M. Gambini ◽  
G. L. Guizzi
Keyword(s):  
Natural Gas ◽  
Power Plants ◽  
Internal Combustion ◽  
Steam Flow ◽  
Inlet Temperature ◽  
Steam Boiler ◽  
Critical Approach ◽  
Steam Power ◽  
Steam Power Plants ◽  
Steam Cycle

In this paper a new kind of steam cycle provided with internal combustion is proposed. The internal combustion of natural gas and compressed air inside the steam flow has been conceived to carry out a steam heating (SH a/o RH) until TIT (Turbine Inlet Temperature) much higher than those of the conventional steam power plants. By this internal combustion it seems possible to overcome the present limits to TIT in steam plants which are, as known, especially related to the technological problems of the superheater tube materials in the conventional external combustion steam boilers. The proposed cycle has been named with the acronym GIST (Gas Injection STeam) since the hot gases resulting from a combustion close to stechiometric conditions are injected inside the steam flow. This paper provides a first critical approach to these new kinds of thermodynamical cycles. At the first the thermodynamical and technological problems related to the combustion inside steam are explained and discussed. Then, different plant lay-out solutions are proposed with a critical discussion on their overall performance. At the last two GIST solution have been defined that seem very interesting: the first is an hybrid plant scheme (i.e. provided with multi-fuel supply) which involves performances higher than conventional steam power plants (net electric efficiency of about 47%); the second is a plant scheme with full natural gas supply (i.e. without multi-fuel steam boiler) wich involves very relevant performances (net electric efficiency of about 57%).

MATLAB AS A TOOL FOR THE TEACHING OF RANKINE CYCLE WITH SIMULATION OF A SIMPLE STEAM POWER PLANT

2015 ◽  
Vol 77 (28) ◽  
Author(s):  
Marwan Affandi ◽  
Ilmi Abdullah ◽  
Nurul Syahirah Khalid
Keyword(s):  
Power Plant ◽  
Power Plants ◽  
Rankine Cycle ◽  
Important Application ◽  
Steam Power ◽  
Power Cycles ◽  
Steam Power Plant ◽  
Steam Power Plants

Rankine cycle is one example of vapor power cycles. One important application is in steam power plants. Properties of the important points in the cycle can be found from steam tables. However, reading values from a steam table is rather inconvenient particularly when there are many values to be read such in a simulation. Interpolation must often be done since the table only provides values of properties at determined points. Using equations of states for steam is very convenient since values can be computed quickly. Unfortunately, equations of states for steam are very complicated. A program written in MATLAB to assist the teaching of Rankine cycle using steam has been developed. MATLAB is used since it is widely available. Using this program, a lecturer can easily modify a problem and get the answer quickly. Students can also benefit from the program where they can solve problems and compare the results that they will get manually.  

scholarly journals Design of a Simple Model of S. P. P. to Study the Effect of Increasing the Boiler Pressure on the Efficiency of the Model

2021 ◽  
Vol 2 (1) ◽  
pp. 1-7
Author(s):  
Abdlmanam Elmaryami ◽  
Hafied M. B. Khalid ◽  
Abdulssalam M. Abdulssalam ◽  
Alaa A. Abdulssalam ◽  
Mohamed M. Alssafi ◽  
...  
Keyword(s):  
Simple Model ◽  
Thermal Efficiency ◽  
Power Plants ◽  
Rankine Cycle ◽  
Important Application ◽  
Working Fluid ◽  
Operating Pressure ◽  
Steam Power ◽  
Power Cycles ◽  
Steam Power Plants

The Rankine cycle is one example of vapor power cycles. One important application of it is in steam power plants. In this paper, a simple model of the steam power plant is designed to study the effect of increasing boiler's pressures (3, 4, 5, and 6 bar respectively) on the efficiency and the dryness friction of the Model. Properties of the important points in the cycle were calculated consequently the losses in the pump, the losses in the condenser, expansion of the working fluid through the turbine, and the heat transfer to the working fluid through the boiler were determined. From the results, it was found that with the increasing of the boiler's operating pressure the thermal efficiency of the model cycle increases due to a substantial increase in network. Thus net-effect is marked increases in the thermal efficiency of the cycle on account of these measures.

Evaluation of Si Coating on Ferritic Steels by CVD-FBR Technology in Steam Oxidation

2009 ◽  
Vol 289-292 ◽  
pp. 413-420 ◽  
Author(s):  
F.J. Bolívar ◽  
L. Sánchez ◽  
M.P. Hierro ◽  
F.J. Pérez
Keyword(s):  
Power Plants ◽  
Protective Coatings ◽  
Steam Oxidation ◽  
Steam Turbines ◽  
X Ray Diffraction ◽  
Steam Power ◽  
Factors Affecting ◽  
Steam Power Plants ◽  
Temperature And Pressure ◽  
Major Factors

The development of new power generation plants firing fossil fuel is aiming at achieving higher thermal efficiencies of the energy conversion process. The major factors affecting the efficiency of the conventional steam power plants are the temperature and, to a lesser extent, the pressure of the steam entering the turbine. The increased operating temperature and pressure require new materials that have major oxidation resistance. Due to this problem, in the last years numerous studies have been conducted in order to develop new coatings to enhance the resistance of steels with chromium contents between 9 and 12% wt against steam oxidation in order to allow operation of steam turbines at 650 0C. In this study, Si protective coatings were deposited by CVD-FBR on ferritic steel P-91. These type of coatings have shown to be protective at 650 0C under steam for at least 3000 hours of laboratory steam exposure under atmospheric pressure. Morphology and composition of coatings were characterized by different techniques, such as scanning electron microscopy (SEM), electron probe microanalysis, and X-ray diffraction (XRD). The results show a substantial increase of steam oxidation protection afforded by Si coating by CVD-FBR process.

Numerical and Experimental Investigations of the Transient Thermal Behavior of a Steam By-Pass Valve at Steam Temperatures Beyond 700 °C

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
Anis Haj Ayed ◽  
Martin Kemper ◽  
Karsten Kusterer ◽  
Hailu Tadesse ◽  
Manfred Wirsum ◽  
...  
Keyword(s):  
Thermal Behavior ◽  
Power Plants ◽  
Numerical Approach ◽  
Life Assessment ◽  
Experimental Investigations ◽  
Steam Power ◽  
Steam Power Plants ◽  
Cyclic Operation ◽  
Measurement Results ◽  
Transient Thermal

Increasing the efficiency of steam power plants is important to reduce their CO2 emissions and can be achieved by increasing steam temperatures beyond 700 °C. Within the present study, the thermal behavior of a steam by-pass valve subject to cyclic operation with 700 °C steam is investigated experimentally and numerically. An innovative numerical approach was applied to predict the valve’s thermal behavior during cyclic operation, which is essential for fatigue life assessment of such a component. Validation of the applied numerical approach has shown good agreement with measurement results, indicating the potential of its application for the valve design process.

Energy Storage Using Low-Pressure Feedwater

1985 ◽  
Vol 107 (3) ◽  
pp. 569-573 ◽  
Author(s):  
C. M. Harman ◽  
S. Loesch
Keyword(s):  
Energy Storage ◽  
Power Plants ◽  
Storage System ◽  
Energy Storage System ◽  
Low Pressure ◽  
Steam Power ◽  
Low Pressure Turbine ◽  
Availability Analysis ◽  
Steam Power Plants ◽  
And Storage

A method for increasing the peak output of steam power plants through use of a low-pressure feedwater storage system is presented. The generalized availability analysis involves only the low-pressure turbine, low-pressure feedwater heaters, and the storage system. With daily cycling and storage charging at near base load conditions, the turnaround efficiency of the energy storage system was found to approach 100 percent. Storage system turnaround efficiency is decreased when the energy is stored during plant part-load operation.

Sign in / Sign up

Export Citation Format

Share Document