Discussion: “An Axial Compressor End-Wall Boundary Layer Calculation Method” (De Ruyck, J., Hirsch, C., and Kool, P., 1979, ASME J. Eng. Power, 101, pp. 233–245)

1979 ◽  
Vol 101 (2) ◽  
pp. 248-248
Author(s):  
L. H. Smith
Keyword(s):  
Boundary Layer ◽  
Calculation Method ◽  
Axial Compressor ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
End Wall

An Axial Compressor End-Wall Boundary Layer Calculation Method

1979 ◽  
Vol 101 (2) ◽  
pp. 233-245 ◽  
Author(s):  
J. De Ruyck ◽  
C. Hirsch ◽  
P. Kool
Keyword(s):  
Experimental Data ◽  
Boundary Layer ◽  
Velocity Profile ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Wall Region ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
End Wall

An axial compressor end-wall boundary layer theory which requires the introduction of three-dimensional velocity profile models is described. The method is based on pitch-averaged boundary layer equations and contains blade force-defect terms for which a new expression in function of transverse momentum thickness is introduced. In presence of tip clearance a component of the defect force proportional to the clearance over blade height ratio is also introduced. In this way two constants enter the model. It is also shown that all three-dimensional velocity profile models present inherent limitations with regard to the range of boundary layer momentum thicknesses they are able to represent. Therefore a new heuristic velocity profile model is introduced, giving higher flexibility. The end-wall boundary layer calculation allows a correction of the efficiency due to end-wall losses as well as calculation of blockage. The two constants entering the model are calibrated and compared with experimental data allowing a good prediction of overall efficiency including clearance effects and aspect ratio. Besides, the method allows a prediction of radial distribution of velocities and flow angles including the end-wall region and examples are shown compared to experimental data.

Modeling the 3-D Flow Effects on Deviation Angle for Axial Compressor Middle Stages

1986 ◽  
Vol 108 (1) ◽  
pp. 131-137 ◽  
Author(s):  
W. B. Roberts ◽  
G. K. Serovy ◽  
D. M. Sandercock
Keyword(s):  
Boundary Layer ◽  
Layer Thickness ◽  
Boundary Layer Thickness ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Blade Element Theory ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
Flow Effects ◽  
End Wall

A model of the spanwise variation of the 3-D flow effects on deviation is proposed for middle-stage rotors and stators. This variation is taken as the difference above or below that predicted by blade element theory at any spanwise location. It was found that the stator variation is strongly affected by the end-wall boundary-layer thickness as well as camber, solidity, and blade channel aspect ratio. Rotor variation was found to depend on end-wall boundary layer thickness and tip clearance normalized by blade span. If these parameters are known or can be calculated, the models provide a reasonable approximation to the spanwise variation of deviation for middle compressor stages operating at low to high subsonic inlet Mach numbers.

Investigations of an Axial Compressor End-Wall Boundary Layer Prediction Method

1981 ◽  
Vol 103 (1) ◽  
pp. 20-33 ◽  
Author(s):  
J. De Ruyck ◽  
C. Hirsch
Keyword(s):  
Boundary Layer ◽  
Velocity Profile ◽  
Boundary Layers ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Diffusion Factor ◽  
Profile Model ◽  
Wall Boundary Layer ◽  
Wall Boundary ◽  
End Wall

A previously developed axial compressor end-wall boundary layer calculation method which requires the introduction of three-dimensional velocity profile models is summarized. In this method the classical three-dimensional velocity profile models were shown to present inherent limitations at stall limit, with regard to the range of transverse boundary layer thicknesses they are able to represent. A corrected profile model is presented which contains no more limitations without affecting the previous found overall results. Stall limit is predicted by limiting values of shape factor and/or diffusion factor. The new profile model containing also compressibility effects allows the calculation of boundary layers in machines with shrouded blades, by simulating the jump between rotating and non rotating parts of the walls. A corrected version of a force defect correlation is presented which is shown to give better agreement at high incidences. Some results on high and low speed machines are discussed. The model is applied to obtain an end-wall blockage correlation depending on geometry, flow coefficient, AVR, aspect ratio, solidity, diffusion factor, Reynolds number, axial blade spacing, tip clearance and inlet boundary layer thickness. A quantitative estimation of the losses associated with the end-wall boundary layers can be obtained using this analysis and therefore can be a useful tool in the design of an axial compressor stage.

Sign in / Sign up

Export Citation Format

Share Document