The Effect of a Transversely Injected Stream on the Flow through Turbine Cascades—Part III: Influence of Aspect Ratio

1979 ◽  
Vol 101 (1) ◽  
pp. 61-67
Author(s):  
B. A. Aburwin ◽  
N. R. L. Maccallum
Keyword(s):  
Aspect Ratio ◽  
Stagnation Pressure ◽  
Dimensional Theory ◽  
One Dimensional ◽  
Flow Capacity ◽  
Aspect Ratios ◽  
New Instrumentation ◽  
Flow Through ◽  
Turbine Cascades ◽  
End Wall

An experimental investigation has been made of the effect of a transversely injected stream on the flow through turbine cascades similar to those in which previous studies [1, 2] had been made, but having aspect ratios of 1.5 and 1.0 compared to the previous value of 3.0. New instrumentation includes a five-hole probe. The average losses in stagnation pressure and the changes in flow capacity remain in agreement with one-dimensional theory. The exit vortex is moved towards the end-wall as aspect ratio is reduced. The strength of the vortex is diminished when the aspect ratio is reduced from 3.0 to 1.5, but there is little change for the further reduction of aspect ratio.

scholarly journals The wave-induced flow of internal gravity wavepackets with arbitrary aspect ratio

2017 ◽  
Vol 834 ◽  
pp. 385-408 ◽  
Author(s):  
T. S. van den Bremer ◽  
B. R. Sutherland
Keyword(s):  
Aspect Ratio ◽  
Three Dimensional ◽  
Mean Flow ◽  
One Dimensional ◽  
Unidirectional Flow ◽  
Aspect Ratios ◽  
Non Local ◽  
Flow Through ◽  
Induced Flow ◽  
Wave Induced

We examine the wave-induced flow of small-amplitude, quasi-monochromatic, three-dimensional, Boussinesq internal gravity wavepackets in a uniformly stratified ambient. It has been known since Bretherton (J. Fluid Mech., vol. 36 (4), 1969, pp. 785–803) that one-, two- and three-dimensional wavepackets induce qualitatively different flows. Whereas the wave-induced mean flow for compact three-dimensional wavepackets consists of a purely horizontal localized circulation that translates with and around the wavepacket, known as the Bretherton flow, such a flow is prohibited for a two-dimensional wavepacket of infinite spanwise extent, which instead induces a non-local internal wave response that is long compared with the streamwise extent of the wavepacket. One-dimensional (horizontally periodic) wavepackets induce a horizontal, non-divergent unidirectional flow. Through perturbation theory for quasi-monochromatic wavepackets of arbitrary aspect ratio, we predict for which aspect ratios which type of induced mean flow dominates. We compose a regime diagram that delineates whether the induced flow is comparable to that of one-, two- or compact three-dimensional wavepackets. The predictions agree well with the results of fully nonlinear three-dimensional numerical simulations.

The Effect of a Transversely Injected Stream on the Flow Through Turbine Cascades: Part II — Performance Changes

1977 ◽  
Author(s):  
K. D. Shrivastava ◽  
N. R. L. MacCallum
Keyword(s):  
Flow Injection ◽  
Transverse Flow ◽  
Stagnation Pressure ◽  
Main Flow ◽  
Secondary Flows ◽  
Pressure Losses ◽  
Flow Through ◽  
Turbine Cascades ◽  
Inlet Angle ◽  
End Wall

This paper reports the changes in the performance of three turbine cascades when a transverse flow is injected from an end-wall into the main flow immediately in front of the cascade The cascades used the same blade profiles, but set at stagger angles of 35, 40 and 45 deg. The effects of the following other variables were also investigated — main flow inlet angle, injection jet inclination to main flow, injection jet velocity, and jet width. The performance changes were assessed by measurements of averaged stagnation pressure losses, reductions in flow capacities, measurements of secondary flows within the channel, and measurements of the exit vortex.

scholarly journals The Effect of a Transversely Injected Stream on the Flow Through Turbine Cascades: Part I — Flow Effects

1977 ◽  
Author(s):  
K. D. Shrivastava ◽  
N. R. L. MacCallum
Keyword(s):  
Separation Bubble ◽  
Transverse Flow ◽  
Main Flow ◽  
Turbine Cascade ◽  
Suction Surface ◽  
Total Head ◽  
Flow Through ◽  
Turbine Cascades ◽  
Flow Effects ◽  
End Wall

A study has been made of the flow-through turbine cascade when a transverse flow is injected into the main flow immediately in front of the cascade. A separation bubble was observed on the end-wall immediately behind the injection slot. At the suction surface end of this bubble a vortex moved into the main flow and continued downstream through, and beyond, the cascade. The effects of the separation bubble and of the vortex were observed in measurements of pressure around the blade surfaces, in boundary layer transverses on the end-wall, and in total head and directional transverses across the cascade exit.

A Theoretical Analysis of Flow Through the Nucleating Stage in a Low Pressure Steam Turbine

1989 ◽  
Vol 111 (3) ◽  
pp. 236-243 ◽  
Author(s):  
S. A. Skillings ◽  
P. T. Walters ◽  
R. Jackson
Keyword(s):  
Flow Behavior ◽  
Condensation Process ◽  
Dimensional Theory ◽  
One Dimensional ◽  
Heterogeneous Effects ◽  
Pressure Steam ◽  
Droplet Sizes ◽  
Flow Through ◽  
Flow Turbulence ◽  
Efficiency And Reliability

In order to improve steam efficiency and reliability, the phenomena associated with the formation and growth of water droplets must be understood. This paper describes a theoretical investigation into flow behavior in the nucleating stage, where the predictions of a one-dimensional theory are compared with measured turbine data. Results indicate that droplet sizes predicted by homogeneous condensation theory cannot be reconciled with measurements unless fluctuating shock waves arise. Heterogeneous effects and flow turbulence are also discussed along with their implications for the condensation process.

Stokes flow through periodic orifices in a channel

1994 ◽  
Vol 263 ◽  
pp. 207-226 ◽  
Author(s):  
Y. Zeng ◽  
S. Weinbaum
Keyword(s):  
Aspect Ratio ◽  
Stokes Flow ◽  
Three Dimensional ◽  
Plane Wall ◽  
Channel Height ◽  
Infinite Plane ◽  
Electron Microscopic ◽  
Dimensional Solution ◽  
Aspect Ratios ◽  
Flow Through

This paper develops a three-dimensional infinite series solution for the Stokes flow through a parallel walled channel which is obstructed by a thin planar barrier with periodically spaced rectangular orifices of arbitrary aspect ratio B’/d’ and spacing D’. Here B’ is the half-height of the channel and d’ is the half-width of the orifice. The problem is motivated by recent electron microscopic studies of the intercellular channel between vascular endothelial cells which show a thin junction strand barrier with discontinuities or breaks whose spacing and width vary with the tissue. The solution for this flow is constructed as a superposition of Hasimoto's (1958) general solution for the two-dimensional flow through a periodic slit array in an infinite plane wall and a new three-dimensional solution which corrects for the top and bottom boundaries. In contrast to the well-known solutions of Sampson (1891) and Hasimoto (1958) for the flow through zero-thickness orifices of circular or elliptic cross-section or periodic slits in an infinite plane wall, which exhibit characteristic viscous velocity profiles, the present bounded solutions undergo a fascinating change in behaviour as the aspect ratio B’/d’ of the orifice opening is increased. For B’/d’ [Lt ] 1 and (D’ –- d’)/B’ of O(1) or greater, which represents a narrow channel, the velocity has a minimum at the orifice centreline, rises sharply near the orifice edges and then experiences a boundary-layer-like correction over a thickness of O(B’) to satisfy no-slip conditions. For B’/d’ of O(1) the profiles are similar to those in a rectangular duct with a maximum on the centreline, whereas for B’/d’ [Gt ] 1, which describes widely separated channel walls, the solution approaches Hasimoto's solution for the periodic infinite-slit array. In the limit (D’ –- d’)/B’ [Lt ] 1, where the width of the intervening barriers is small compared with the channel height, the solutions exhibit the same behaviour as Lee & Fung's (1969) solution for the flow past a single cylinder. The drag on the zero-thickness barriers in this case is nearly the same as for the cylinder for all aspect ratios.

Experimental Investigation on the Motion of Particle Cloud in Viscous Fluids

2018 ◽  
Vol 141 (3) ◽  
Author(s):  
Amir H. Azimi
Keyword(s):  
Aspect Ratio ◽  
Drag Coefficient ◽  
Viscous Fluids ◽  
Air Bubbles ◽  
Aspect Ratios ◽  
Particle Clouds ◽  
Flow Through ◽  
Using Data ◽  
The Stability ◽  
Individual Particles

Laboratory experiments were conducted to study the dynamics of particle clouds in viscous fluids. Different shapes of frontal head and trailing stems were observed, and particle clouds were classified using data mining methodology. The stability of the frontal head of particle clouds was found to be correlated with the nozzle diameter and mass of sand particles in the form of an initial aspect ratio. The formation of particle clusters into a torus and the split of the frontal head into two or three clusters were investigated in detail. The cluster of particles flow through viscous fluid experienced partial separation due to the release of air bubbles from the rear of frontal head. It was observed that the time and location of major particle separation increase linearly with the aspect ratio. The oscillatory motion of the frontal head, caused by an uneven release of air bubbles from the rear of the frontal head, was found to be correlated with the initial aspect ratio. Both amplitude and wavelength exhibited a linear relationship with nondimensional time. The average drag coefficient of particle clouds Cd in viscous fluids was calculated for different aspect ratios, and the results were compared with the drag coefficient of individual particles. It was found that the averaged drag coefficients of particle clouds were smaller than the drag coefficient of individual particles, and Cd slightly increases with the increasing initial aspect ratio.

Analysis of mixing performances in microchannel with obstacles of different aspect ratios

2019 ◽  
Vol 233 (5) ◽  
pp. 1045-1051 ◽  
Author(s):  
Bappa Mondal ◽  
Sukumar Pati ◽  
PK Patowari
Keyword(s):  
Reynolds Number ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Flow Condition ◽  
Schmidt Number ◽  
Mixing Efficiency ◽  
Rectangular Microchannel ◽  
Mixing Performance ◽  
Aspect Ratios ◽  
Flow Through

In this study, the mixing performance and pressure drop characteristics have been numerically analyzed for flow through rectangular microchannel with obstacles in the walls arranged in a staggered manner. Three different aspect ratios (AR) of the obstacles are considered, namely 4:1, 1:1, and 1:4. The effects of aspect ratio of the obstacles on the mixing efficiency and the pressure drop are analyzed and compared with that of the channel without obstacle. The results are presented in terms of Reynolds number (Re) and Schmidt number (Sc) in the following range: 0.2 ≤ Re ≤ 1 and 500 ≤ Sc ≤ 1500. Enhanced mixing efficiency is achieved for the case of microchannel with obstacles and the corresponding pressure drop is also found to be higher. The mixing efficiency as well as the pressure drop is maximum for AR = 1:4 among all the geometries considered in the analysis in same flow condition. Furthermore, for a given configuration of the microchannel the mixing efficiency is governed by the mass Peclet number and, accordingly, the mixing efficiency increases with the decrease in Schmidt number for a given Reynolds number.

Certain Problems with the Application of Stochastic Diffusion Processes for the Description of Chemical Engineering Phenomena. Stochastic Model of Non-Isothermal Flow Chemical Reactor

1996 ◽  
Vol 61 (2) ◽  
pp. 242-258 ◽  
Author(s):  
Vladimír Kudrna ◽  
Libor Vejmola ◽  
Pavel Hasal
Keyword(s):  
Stochastic Model ◽  
Chemical Engineering ◽  
Diffusion Processes ◽  
Dispersion Model ◽  
Chemical Reactor ◽  
Segregation Index ◽  
One Dimensional ◽  
A Value ◽  
Isothermal Case ◽  
Flow Through

Recently developed stochastic model of a one-dimensional flow-through chemical reactor is extended in this paper also to the non-isothermal case. The model enables the evaluation of concentration and temperature profiles along the reactor. The results are compared with the commonly used one-dimensional dispersion model with Danckwerts' boundary conditions. The stochastic model also enables to evaluate a value of the segregation index.

scholarly journals Effects of Steel Fiber Percentage and Aspect Ratios on Fresh and Harden Properties of Ultra-High Performance Fiber

2021 ◽  
Vol 2 (3) ◽  
pp. 501-515
Author(s):  
Rajib Kumar Biswas ◽  
Farabi Bin Ahmed ◽  
Md. Ehsanul Haque ◽  
Afra Anam Provasha ◽  
Zahid Hasan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
High Performance ◽  
Steel Fiber ◽  
Setting Time ◽  
Fiber Reinforced Concrete ◽  
Future Research ◽  
Manufacturing Cost ◽  
Aspect Ratios ◽  
High Performance Fiber

Steel fibers and their aspect ratios are important parameters that have significant influence on the mechanical properties of ultrahigh-performance fiber-reinforced concrete (UHPFRC). Steel fiber dosage also significantly contributes to the initial manufacturing cost of UHPFRC. This study presents a comprehensive literature review of the effects of steel fiber percentages and aspect ratios on the setting time, workability, and mechanical properties of UHPFRC. It was evident that (1) an increase in steel fiber dosage and aspect ratio negatively impacted workability, owing to the interlocking between fibers; (2) compressive strength was positively influenced by the steel fiber dosage and aspect ratio; and (3) a faster loading rate significantly improved the mechanical properties. There were also some shortcomings in the measurement method for setting time. Lastly, this research highlights current issues for future research. The findings of the study are useful for practicing engineers to understand the distinctive characteristics of UHPFRC.

Sign in / Sign up

Export Citation Format

Share Document