scholarly journals Discussion: “Experimental Study of the Flow Field Within a Transonic Axial Compressor Rotor by Laser Velocimetry and Comparison With Through-Flow Calculations” (Dunker, R. J., Strinning, P. E., and Weyer, H. B., 1978, ASME J. Eng. Power, 100, pp. 279–286)

1978 ◽  
Vol 100 (2) ◽  
pp. 286-286
Author(s):  
Ch. Hirsch
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Axial Compressor ◽  
Laser Velocimetry ◽  
Compressor Rotor ◽  
Through Flow ◽  
Transonic Axial Compressor

Experimental Study of the Flow Field Within a Transonic Axial Compressor Rotor by Laser Velocimetry and Comparison With Through-Flow Calculations

1978 ◽  
Vol 100 (2) ◽  
pp. 279-286 ◽  
Author(s):  
R. J. Dunker ◽  
P. E. Strinning ◽  
H. B. Weyer
Keyword(s):  
Flow Field ◽  
Pressure Ratio ◽  
Analytical Data ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Compressor Rotor ◽  
Through Flow ◽  
Equivalent Mass ◽  
Transonic Axial Compressor ◽  
Design Speed

The flow field ahead, within, and behind the rotor of a transonic axial compressor designed for a total pressure ratio of 1.51 at a relative tip Mach number of 1.4 has been studied in detail using an advanced laser velocimeter. The tests were carried out at 70 and 100 percent design speed (20,260 rpm) and equivalent mass flows corresponding to the point of maximum isentropic efficiency. The tests yielded quite complete data on the span- and gap-wise velocity profiles, on the three-dimensional shock waves in and outside of the rotor blade channels, and on the blade wakes. Some of the experimental results will be submitted, discussed, and compared to corresponding analytical data of a through-flow calculation. The comparison reveals considerable discrepancies inside the blade row between the two-dimensional calculation and the experiments primarily due to the loss and deviation correlations used, as well as to the distribution of losses and flow angles inside the blade channels.

Difference in the Working Principle of Axial Slot and Tip Blowing Casing Treatments

2016 ◽  
Author(s):  
André Inzenhofer ◽  
Cyril Guinet ◽  
Andreas Hupfer ◽  
Bernd Becker ◽  
Patrick Grothe ◽  
...  
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Negative Effect ◽  
Working Principle ◽  
Transonic Axial Compressor ◽  
The Difference ◽  
Casing Treatments

Tip blowing and axial slot casing treatments have shown their ability to enhance the stability of a transonic axial compressor with different effects on efficiency. For an effective application of these casing treatments, a good knowledge of the influence of the casing treatment on the rotor flow field is important. There is still a need for more detailed investigations, in order to understand the interaction between the treatment and the near casing 3D flow field. For transonic compressor rotors this interaction is more complex, as super- and subsonic flow regions alternate while interacting with the casing treatment. In the present study, an axial slot and a tip blowing casing treatment, which have been developed and optimized for the same tip critical transonic axial compressor rotor (reference rotor) by Streit et al. [1] and Guinet et al. [2], are subject of the investigation. Both casing treatment types showed their capabilities to enhance the compressor stability without losing by means of CFD simulations. Since the higher compressor stability allows a higher blade loading, Streit et al. reduced the blade number of the rotor. Thus, the efficiency was increased due to the reduction of friction losses. However, applying the tip blowing casing treatment to the reduced rotor shows a negative effect on the efficiency. Both casing treatment types recirculate flow from a downstream to an upstream location of the rotor and reinject it to enhance the near casing flow field. Although the working principle of the two casing treatment types are similar, the transfer of the casing treatments from the reference to the reduced rotor show different trends in efficiency. Therefore, the effect of recirculation cannot explain the difference in efficiency. Hence, applying axial slots must include additional flow features, compared to recirculation channels. Compensating effects as in circumferential groove casing treatments and other flow interactions between the near casing flow field and the slot flow are considered. These additional mechanisms of the axial slot casing treatment will be identified and isolated by comparing the two different casing treatment types. The numerical simulations are carried out on a 1.5 stage transonic axial compressor using URANS simulations.

Study of the Standard k-ε Model for Tip Leakage Flow in an Axial Compressor Rotor

2016 ◽  
Vol 33 (4) ◽  
Author(s):  
Yanfei Gao ◽  
Yangwei Liu ◽  
Luyang Zhong ◽  
Jiexuan Hou ◽  
Lipeng Lu
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Turbulent Viscosity ◽  
Axial Compressor ◽  
Leakage Flow ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor

AbstractThe standard k-ε model (SKE) and the Reynolds stress model (RSM) are employed to predict the tip leakage flow (TLF) in a low-speed large-scale axial compressor rotor. Then, a new research method is adopted to “freeze” the turbulent kinetic energy and dissipation rate of the flow field derived from the RSM, and obtain the turbulent viscosity using the Boussinesq hypothesis. The Reynolds stresses and mean flow field computed on the basis of the frozen viscosity are compared with the results of the SKE and the RSM. The flow field in the tip region based on the frozen viscosity is more similar to the results of the RSM than those of the SKE, although certain differences can be observed. This finding indicates that the non-equilibrium turbulence transport nature plays an important role in predicting the TLF, as well as the turbulence anisotropy.

The Impact of Manufacturing Variations on Performance of a Transonic Axial Compressor Rotor

2018 ◽  
Author(s):  
Marcus Lejon ◽  
Niklas Andersson ◽  
Lars Ellbrant ◽  
Hans Mårtensson
Keyword(s):  
Flow Field ◽  
Geometric Mean ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Mean Deviation ◽  
Design Intent ◽  
Compressor Rotor ◽  
Measuring Machine ◽  
The Mean ◽  
The Impact

In this paper, the impact of manufacturing variations on performance of an axial compressor rotor are evaluated at design rotational speed. The geometric variations from the design intent were obtained from an optical coordinate measuring machine and used to evaluate the impact of manufacturing variations on performance and the flow field in the rotor. The complete blisk is simulated using 3D CFD calculations, allowing for a detailed analysis of the impact of geometric variations on the flow. It is shown that the mean shift of the geometry from the design intent is responsible for the majority of the change in performance in terms of mass flow and total pressure ratio for this specific blisk. In terms of polytropic efficiency, the measured geometric scatter is shown to have a higher influence than the geometric mean deviation. The geometric scatter around the mean is shown to impact the pressure distribution along the leading edge and the shock position. Furthermore, a blisk is analyzed with one blade deviating substantially from the design intent, denoted as blade 0. It is shown that the impact of blade 0 on the flow is largely limited to the blade passages that it is directly a part of. The results presented in this paper also show that the impact of this blade on the flow field can be represented by a simulation including 3 blade passages. In terms of loss, using 5 blade passages is shown to give a close estimate for the relative change in loss for blade 0 and neighboring blades.

Turbulence Model Influence on Numerical Investigation of Transonic Axial Compressor Rotor

2011 ◽  
Vol 308-310 ◽  
pp. 1519-1522
Author(s):  
Fang Xie ◽  
Chang Jiang Liu ◽  
You Jun Wang
Keyword(s):  
Experimental Data ◽  
Numerical Investigation ◽  
Turbulence Model ◽  
Characteristic Curve ◽  
Axial Compressor ◽  
Internal Flow ◽  
Turbulent Model ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
Point Forecast

Numerical method using HI and HOH meshing combined B - L turbulent model and S - A turbulent model separately based on the Rotor 37 compressor Rotor was applied to the steady flow. results on pressure characteristic curve, stall point forecast etc were compared with related experimental data. This paper discussed calculation precision influenced by the turbulence model and numerical computation grid. This numerical investigation was basis for subsequent compressor internal flow field study.

Aeroelastic Flutter Investigation and Stability Enhancement of a Transonic Axial Compressor Rotor Using Casing Treatment

2017 ◽  
Author(s):  
Kirubakaran Purushothaman ◽  
Sankar Kumar Jeyaraman ◽  
Ajay Pratap ◽  
Kishore Prasad Deshkulkarni
Keyword(s):  
Flow Separation ◽  
Aerodynamic Force ◽  
Damping Ratio ◽  
Axial Compressor ◽  
Casing Treatment ◽  
Aerodynamic Damping ◽  
Compressor Rotor ◽  
Aeroelastic Flutter ◽  
Blade Tip ◽  
Transonic Axial Compressor

This study discusses in detail the aeroelastic flutter investigation of a transonic axial compressor rotor using computational methods. Fluid structure interaction approach is used in this method to evaluate the unsteady aerodynamic force and work done of a vibrating blade in CFD domain. Energy method and work per cycle approach is adapted for this flutter prediction. A framework has been developed to estimate the work per cycle and aerodynamic damping ratio. Based on the aerodynamic damping ratio, occurrence of flutter is estimated for different inter blade phase angles. Initially, the baseline rotor blade design was having negative aerodynamic damping at part speed conditions. The main cause for this flutter occurrence was identified as large flow separation near blade tip region due to high incidence angles. The unsteadiness in the flow was leading to aerodynamic force fluctuation matching with natural frequency of blade, resulting in excitation of the blades. Hence axially skewed slot casing treatment was implemented to reduce the flow separation at blade tip region to alleviate the onset of flutter. By this method, the stall margin and aerodynamic damping of the test compressor was improved and flutter was avoided.

Sign in / Sign up

Export Citation Format

Share Document