Closure to “Discussions of ‘A Family of Surface Velocity Distributions for Axial Compressor Blading and Their Theoretical Performance’” (1976, ASME J. Eng. Power, 98, pp. 238–239)

1976 ◽  
Vol 98 (2) ◽  
pp. 239-241
Author(s):  
G. J. Walker
Keyword(s):  
Axial Compressor ◽  
Surface Velocity ◽  
Theoretical Performance

A Family of Surface Velocity Distributions for Axial Compressor Blading and Their Theoretical Performance

1976 ◽  
Vol 98 (2) ◽  
pp. 229-238 ◽  
Author(s):  
G. J. Walker
Keyword(s):  
High Performance ◽  
Axial Compressor ◽  
Compressor Blade ◽  
Surface Velocity ◽  
Design Parameters ◽  
Suction Surface ◽  
Wide Range ◽  
Using Data ◽  
High Level ◽  
Theoretical Performance

The influence of free stream disturbances on transition is discussed and it is noted that significant regions of laminar flow may exist on axial turbomachine blades despite the high level of disturbance to which they are subjected. A family of surface velocity distributions giving unseparated flow on the suction surface of an axial compressor blade is derived using data from detailed boundary layer measurements on the blading of a single-stage machine. The distributions are broadly similar to those adopted by Wortmann in designing high performance isolated aerofoil sections for operation at much higher Reynolds numbers. The theoretical performance of blades having the specified surface velocity distributions is computed for a wide range of conditions, and the effects of varying Reynolds number and other design parameters are analyzed. The results suggest the possibility of obtaining useful improvements in performance over that of conventional compressor blade sections. The computed performance values show an almost unique relation between the blade losses and the suction surface diffusion ratio. However the correlation of losses with the equivalent diffusion ratio is found to break down at high values of the latter parameter.

Effects of stator splitter blades on aerodynamic performance of a single-stage transonic axial compressor

2020 ◽  
Vol 14 (4) ◽  
pp. 7369-7378
Author(s):  
Ky-Quang Pham ◽  
Xuan-Truong Le ◽  
Cong-Truong Dinh
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Operating Stability ◽  
Length Coverage

Splitter blades located between stator blades in a single-stage axial compressor were proposed and investigated in this work to find their effects on aerodynamic performance and operating stability. Aerodynamic performance of the compressor was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations using the k-e turbulence model with a scalable wall function. The numerical results for the typical performance parameters without stator splitter blades were validated in comparison with experimental data. The numerical results of a parametric study using four geometric parameters (chord length, coverage angle, height and position) of the stator splitter blades showed that the operational stability of the single-stage axial compressor enhances remarkably using the stator splitter blades. The splitters were effective in suppressing flow separation in the stator domain of the compressor at near-stall condition which affects considerably the aerodynamic performance of the compressor.

Modeling Vibration-Induced Tire-Pavement Interaction Noise in the Mid-frequency Range

2020 ◽  
Author(s):  
Sterling McBride ◽  
Ricardo Burdisso ◽  
Corina Sandu
Keyword(s):  
Sound Intensity ◽  
Element Model ◽  
Dominant Frequency ◽  
Contact Forces ◽  
Surface Velocity ◽  
New Wave ◽  
Normal Surface ◽  
Radiated Noise ◽  
Physical Effects ◽  
Effects Of Rotation

ABSTRACT Tire-pavement interaction noise (TPIN) is one of the main sources of exterior noise produced by vehicles traveling at greater than 50 kph. The dominant frequency content is typically within 500–1500 Hz. Structural tire vibrations are among the principal TPIN mechanisms. In this work, the structure of the tire is modeled and a new wave propagation solution to find its response is proposed. Multiple physical effects are accounted for in the formulation. In an effort to analyze the effects of curvature, a flat plate and a cylindrical shell model are presented. Orthotropic and nonuniform structural properties along the tire's transversal direction are included to account for differences between its sidewalls and belt. Finally, the effects of rotation and inflation pressure are also included in the formulation. Modeled frequency response functions are analyzed and validated. In addition, a new frequency-domain formulation is presented for the computation of input tread pattern contact forces. Finally, the rolling tire's normal surface velocity response is coupled with a boundary element model to demonstrate the radiated noise at the leading and trailing edge locations. These results are then compared with experimental data measured with an on-board sound intensity system.

Sign in / Sign up

Export Citation Format

Share Document