Dynamic Model of a Sac-Type Pneumatically Driven Artificial Ventricle

1977 ◽  
Vol 99 (1) ◽  
pp. 14-19 ◽  
Author(s):  
D. B. Geselowitz ◽  
G. E. Miller ◽  
W. M. Phillips
Keyword(s):  
Dynamic Model ◽  
Circulatory System ◽  
Operating Conditions ◽  
Time Varying ◽  
Outlet Port ◽  
Mock Circulatory System ◽  
Linear Resistance ◽  
Wide Range ◽  
Artificial Ventricle ◽  
Nonlinear Resistance

Inlet and outlet pressures and flows were obtained over a wide range of operating conditions for a pneumatically driven sac-type artificial ventricle connected to a mechanical mock circulatory system. The load presented to the ventricle by the mock circulatory system was found to be characterized by a linear resistance and capacitance. A dynamic model for the ventricle which accounted for instantaneous pressures and flows was developed. The outlet port is characterized by an inertance and square law resistance; the inlet port is characterized by a nonlinear resistance dependent on the type of valve. The input to the model is the time varying sac pressure. The model predicts the fill-limited and ejection-limited modes of the artificial ventricle.

Analysis of an Artificial Ventricle and Mock Circulatory System

1977 ◽  
Vol 99 (4) ◽  
pp. 184-188 ◽  
Author(s):  
K. M. High ◽  
J. A. Brighton ◽  
A. D. Brickman ◽  
W. S. Pierce
Keyword(s):  
Artificial Heart ◽  
Circulatory System ◽  
Experimental Tests ◽  
Mean Flow ◽  
Actual System ◽  
Mock Circulatory System ◽  
System A ◽  
The Mean ◽  
Artificial Ventricle ◽  
Good Agreement

A mathematical model is developed for calculating the pressures and flows in an artificial heart, its pneumatic drive unit, and a mock circulatory system. The system is divided into convenient subsystems to facilitate the analysis, and each subsystem is then analyzed separately. The set of independent equations developed is solved on a computer and corresponding experimental tests are made on the actual system. A comparison of the experimental and computer results shows good agreement for the mean flow rate through the pump and also for several instantaneous pressures and flow rates in the system.

Hydrodynamic Characterisation of Ventricular Assist Devices

2001 ◽  
Vol 24 (7) ◽  
pp. 470-477 ◽  
Author(s):  
S. Vandenberghe ◽  
P. Segers ◽  
B. Meyns ◽  
P. Verdonck
Keyword(s):  
Circulatory System ◽  
Ventricular Assist Devices ◽  
Test Fluid ◽  
Hydrodynamic Characteristics ◽  
Ventricular Assist ◽  
Assist Devices ◽  
Mock Circulatory System ◽  
Wide Range ◽  
Displacement Pump ◽  
Hemodynamic Performance

A new mock circulatory system (MCS) was designed to evaluate and characterise the hydraulic performance of ventricular assist devices (VADs). The MCS consists of a preload section and a multipurpose afterload section, with an adjustable compliance chamber (C) and peripheral resistor (Rp) as principal components. The MCS was connected to a pulse duplicator system for validation, simulating a wide range of afterload conditions. Both pressure and flow were measured, and the values of the different components calculated. The data perfectly fits a 4-element electrical analogon (EA). The MCS was further used to assess the hydrodynamic characteristics of the Medos VAD as an example of a displacement pump. Data was measured for various MCS settings and at different pump rates, yielding device specific pump function graphs for water and pig blood. Our data demonstrate (i) flow sensitivity to preload and afterload and (ii) the effect of test fluid on hemodynamic performance.

Nonlinear Dynamic Model of a Two-Stage Pressure Relief Valve for Designers

2001 ◽  
Vol 124 (1) ◽  
pp. 62-66 ◽  
Author(s):  
Pei-Sun Zung ◽  
Ming-Hwei Perng
Keyword(s):  
Dynamic Model ◽  
Nonlinear Dynamic ◽  
Dynamic Models ◽  
Operating Conditions ◽  
Model Parameters ◽  
Nonlinear Dynamic Model ◽  
Relief Valve ◽  
Two Stage ◽  
Pressure Relief ◽  
Wide Range

This paper presents a handy nonlinear dynamic model for the design of a two stage pilot pressure relief servo-valve. Previous surveys indicate that the performance of existing control valves has been limited by the lack of an accurate dynamic model. However, most of the existing dynamic models of pressure relief valves are developed for the selection of a suitable valve for a hydraulic system, and assume model parameters which are not directly controllable during the manufacturing process. As a result, such models are less useful for a manufacturer eager to improve the performance of a pressure valve. In contrast, model parameters in the present approach have been limited to dimensions measurable from the blue prints of the valve such that a specific design can be evaluated by simulation before actually manufacturing the valve. Moreover, the resultant model shows excellent agreement with experiments in a wide range of operating conditions.

Aortic Pressure Estimation With Electro-Mechanical Circulatory Assist Devices

1993 ◽  
Vol 115 (2) ◽  
pp. 187-194 ◽  
Author(s):  
J. F. Gardner ◽  
M. Ignatoski ◽  
U. Tasch ◽  
A. J. Snyder ◽  
D. B. Geselowitz
Keyword(s):  
Initial Conditions ◽  
Circulatory System ◽  
Time History ◽  
Aortic Pressure ◽  
Operating Conditions ◽  
Observer Performance ◽  
Mean Deviation ◽  
Mock Circulatory System ◽  
The Mean

An adaptive technique for the estimation of the time history of aortic pressure (from applied voltage and position feedback) has been designed, implemented, and bench tested using the Penn State Electric Ventricular Assist Device (EVAD). This method, known in the field of automatic control as a dynamic observer, utilizes gains which were determined using experimental data collected while the EVAD was running on a mock circulatory system. An adaptive scheme provides the observer with a method of changing its initial conditions on a stroke-by-stroke basis which improves observer performance. In both determining the feedback gains and developing the adaptation scheme, a range of beat rates and pressure loads was taken into account to yield satisfactory observer performance over a range of operating conditions. The observer was implemented, its performance was verified in vitro and results are reported. In the six experimental operating conditions, the beat rate ranged from 56-104 beats per minute (bpm) and the span of the mean systolic aortic pressure was 10.7-18.7 kPa (80–140 mmHg). For these cases, the mean deviation between the actual and estimated aortic pressure during the latter two-thirds of systole was 0.41 kPa (3.1 mmHg).

Dynamic Model of a Novel Alternating Flow (AF) Hydraulic Pump

2017 ◽  
Author(s):  
Mengtang M. Li ◽  
Ryan Foss ◽  
Kim A. Stelson ◽  
James D. Van de Ven ◽  
Eric J. Barth
Keyword(s):  
Dynamic Model ◽  
High Efficiency ◽  
Check Valve ◽  
Viscous Friction ◽  
Operating Conditions ◽  
Hydraulic Systems ◽  
Displacement Control ◽  
Hydraulic Pump ◽  
Wide Range ◽  
Variable Displacement

High power density and good controllability are the most appealing characteristics that make hydraulic systems the best choice for many applications. Current state of the art hydraulic variable displacement pumps show high efficiency at high displacement while they have poor efficiencies at low displacement. This paper proposes a novel alternating flow (AF) variable displacement hydraulic pump to 1) eliminate metering losses by acting as a high-bandwidth pump for displacement control, 2) achieve high efficiency across a wide range of operating conditions and displacements, and 3) allow multiple units to be easily common-shaft mounted for a compact multi-actuator displacement control system from a single prime-mover. A dynamic model using first principles describes the cylinder pressure, flows between pairs of cylinders, and net inlet and outlet flows as a function of the pump’s phase shift angle. The model captures hydraulic check valve dynamics, the effective bulk modulus, leakage flows, and viscous friction. Piston kinematics and dynamics are discussed and energy loss models are presented and used to guide the design for a first prototype of the AF hydraulic pump. The paper presents simulation results from the model that offer an initial evaluation of this novel pump concept and potential applications.

Dynamic Optimization of Spur Gears

2007 ◽  
Author(s):  
M. Faggioni ◽  
F. Pellicano ◽  
A. Andrisano ◽  
G. Bertacchi
Keyword(s):  
Dynamic Model ◽  
Computational Cost ◽  
Optimization Method ◽  
Operating Conditions ◽  
Lumped Mass ◽  
Mass System ◽  
Profile Modification ◽  
Wide Range ◽  
Random Simplex ◽  
Using Data

This paper presents a global optimization method able to find gear profile modifications that minimize vibrations. A non linear dynamic model is used to study the vibrational behavior; the dynamic model is validated using data available in literature. The optimization method takes into account the influence of torque levels both on the static and the dynamic response. Therefore, two different objective functions are considered; the first one is based on static analysis and the second one is based on the dynamic behavior of a lumped mass system. The procedure can find the optimal profile modification that reduce the vibrations over a wide range of operating conditions. In order to reduce the computational cost, a Random-Simplex optimization algorithm is developed; the optimum reliability is also estimated using a Monte Carlo simulation. The approach shows good performances both for the computational efficiency and the reliability of results.

scholarly journals Dynamic model of nuclear power plant steam turbine

2015 ◽  
Vol 25 (1) ◽  
pp. 65-86 ◽  
Author(s):  
Karol Kulkowski ◽  
Anna Kobylarz ◽  
Michał Grochowski ◽  
Kazimierz Duzinkiewicz
Keyword(s):  
Power Plant ◽  
Nuclear Power Plant ◽  
Steam Turbine ◽  
Dynamic Model ◽  
Nuclear Power ◽  
Dynamic Models ◽  
Operating Conditions ◽  
Internal Variables ◽  
Wide Range ◽  
Optimal Process Control

Abstract The paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations evaluated directly from the input to the output, including pressure drop at the stages. As the input, model takes opening degree of valve and steam properties: mass flow and pressure. Moreover, it allows access to many internal variables (besides input and output) describing processes within the turbine. The model is compared with the static steam turbine model and then verified by using archive data gained from researches within previous Polish Nuclear Power Programme. Presented case study concerns the WWER-440 steam turbine that was supposed to be used in Żarnowiec. Simulation carried out shows compliance of the static and dynamic models with the benchmark data, in a steady state conditions. Dynamic model also shows good behavior over the transient conditions.

Comparison of Deterministic and Linear Cosine Spatial Filtering of Transmission Electron Micrographs

1972 ◽  
Vol 30 ◽  
pp. 596-597
Author(s):  
David A. Ansley
Keyword(s):  
Spherical Aberration ◽  
Focal Length ◽  
Chromatic Aberration ◽  
Spatial Filter ◽  
Operating Conditions ◽  
Objective Lens ◽  
List Type ◽  
Spatial Filters ◽  
Transmission Electron ◽  
Wide Range

The coherence of the electron flux of a transmission electron microscope (TEM) limits the direct application of deconvolution techniques which have been used successfully on unmanned spacecraft programs. The theory assumes noncoherent illumination. Deconvolution of a TEM micrograph will, therefore, in general produce spurious detail rather than improved resolution.A primary goal of our research is to study the performance of several types of linear spatial filters as a function of specimen contrast, phase, and coherence. We have, therefore, developed a one-dimensional analysis and plotting program to simulate a wide 'range of operating conditions of the TEM, including adjustment of the:(1) Specimen amplitude, phase, and separation(2) Illumination wavelength, half-angle, and tilt(3) Objective lens focal length and aperture width(4) Spherical aberration, defocus, and chromatic aberration focus shift(5) Detector gamma, additive, and multiplicative noise constants(6) Type of spatial filter: linear cosine, linear sine, or deterministic

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

Sign in / Sign up

Export Citation Format

Share Document