The Theory of Static Loads in Bins

1977 ◽  
Vol 44 (3) ◽  
pp. 409-412 ◽  
Author(s):  
S. C. Cowin
Keyword(s):  
Granular Material ◽  
Cross Section ◽  
Horizontal Stress ◽  
Vertical Stress ◽  
Average Pressure ◽  
Classical Formula ◽  
Horizontal Cross Section ◽  
Cross Sectional ◽  
Static Loads ◽  
Actual Stress

The classical formula for the pressure in deep bins containing granular material is derived here employing considerably weaker assumptions than previous derivations. Three important points are established in this rigorous derivation. First, it is shown that the classical formula due to Janssen is a lower bound on the average pressure the granular material can exert on a bin wall rather than necessarily the actual stress. Second, it is shown that Janssen’s assumption of constant vertical stress over the bin’s horizontal cross section is not necessary to obtain his classical formula. Third, it is shown that the coefficient introduced by Janssen should be interpreted as the ratio of the horizontal stress averaged over the lateral boundary perimeter to the vertical stress averaged over the horizontal cross-sectional area of the bin.

The Pressure Ratio in the Theory of Bin Pressures

1979 ◽  
Vol 46 (3) ◽  
pp. 524-528 ◽  
Author(s):  
S. C. Cowin
Keyword(s):  
Granular Material ◽  
Bulk Density ◽  
Pressure Ratio ◽  
Vertical Wall ◽  
Yield Condition ◽  
Horizontal Stress ◽  
Vertical Stress ◽  
Linear Functions ◽  
Cross Sectional ◽  
Cross Sectional Average

The pressure ratio K0 is assumed to be a constant in the theory developed by Janssen for determining the pressures imparted by a granular material to its container. Recently it was shown that K0 can be defined less restrictively as the ratio of the perimeter average of the horizontal stress acting on the vertical wall of the container to the cross-sectional average of the vertical stress in the granular material at the same depth in the container. Three results concerning K0 are presented in this paper. First, it is shown that the essential result of Janssen, namely that the vertical and horizontal stresses have a constant bound at great depths, also holds in the case when the bulk density and the pressure, ratio are bounded by linear functions of the average vertical stress. Second, it is shown that a formula relating K0 to the Poisson’s ratio of the granular material is not correct, in general. Third, bounds on K0 are obtained using the Mohr-Coulomb yield condition for the granular material.

Mass Determination by Direct Measurement of Electron Scattering

1975 ◽  
Vol 33 ◽  
pp. 240-241
Author(s):  
M. K. Lamvik ◽  
A. V. Crewe
Keyword(s):  
Cross Section ◽  
Electron Scattering ◽  
Mass Density ◽  
Variable Mass ◽  
Scattering Cross Section ◽  
Mass Determination ◽  
Number Density ◽  
Cross Sectional ◽  
Thin Slice ◽  
Scattering Cross

If a molecule or atom of material has molecular weight A, the number density of such units is given by n=Nρ/A, where N is Avogadro's number and ρ is the mass density of the material. The amount of scattering from each unit can be written by assigning an imaginary cross-sectional area σ to each unit. If the current I0 is incident on a thin slice of material of thickness z and the current I remains unscattered, then the scattering cross-section σ is defined by I=IOnσz. For a specimen that is not thin, the definition must be applied to each imaginary thin slice and the result I/I0 =exp(-nσz) is obtained by integrating over the whole thickness. It is useful to separate the variable mass-thickness w=ρz from the other factors to yield I/I0 =exp(-sw), where s=Nσ/A is the scattering cross-section per unit mass.

A tilting high temperature gas reaction chamber for the JEM 7A T.E.M.

1978 ◽  
Vol 36 (1) ◽  
pp. 70-71
Author(s):  
Brian L. Rhoades
Keyword(s):  
Cross Section ◽  
Reaction Chamber ◽  
Objective Lens ◽  
Reduced Cross Section ◽  
Cross Sectional ◽  
Structural Investigations ◽  
Transmission Electron ◽  
Dynamic Experiments ◽  
Successful Design ◽  
Thermocouple Junction

A gas reaction chamber has been designed and constructed for the JEM 7A transmission electron microscope which is based on a notably successful design by Hashimoto et. al. but which provides specimen tilting facilities of ± 15° aboutany axis in the plane of the specimen.It has been difficult to provide tilting facilities on environmental chambers for 100 kV microscopes owing to the fundamental lack of available space within the objective lens and the scope of structural investigations possible during dynamic experiments has been limited with previous specimen chambers not possessing this facility.A cross sectional diagram of the specimen chamber is shown in figure 1. The specimen is placed on a platinum ribbon which is mounted on a mica ring of the type shown in figure 2. The ribbon is heated by direct current, and a thermocouple junction spot welded to the section of the ribbon of reduced cross section enables temperature measurement at the point where localised heating occurs.

Microstructure of laser-irradiated, conducting Kapton polyimide

1995 ◽  
Vol 53 ◽  
pp. 502-503
Author(s):  
D. L. Callahan ◽  
Z. Ball ◽  
H. M. Phillips ◽  
R. Sauerbrey
Keyword(s):  
Electron Microscopy ◽  
Phase Transition ◽  
Transmission Electron Microscopy ◽  
Cross Section ◽  
Film Surface ◽  
Cross Sectional ◽  
General Utility ◽  
Transmission Electron ◽  
Considerable Debate ◽  
Potential Applications

Ultraviolet laser-irradiation can be used to induce an insulator-to-conductor phase transition on the surface of Kapton polyimide. Such structures have potential applications as resistors or conductors for VLSI applications as well as general utility electrodes. Although the percolative nature of the phase transformation has been well-established, there has been little definitive work on the mechanism or extent of transformation. In particular, there has been considerable debate about whether or not the transition is primarily photothermal in nature, as we propose, or photochemical. In this study, cross-sectional optical microscopy and transmission electron microscopy are utilized to characterize the nature of microstructural changes associated with the laser-induced pyrolysis of polyimide.Laser-modified polyimide samples initially 12 μm thick were prepared in cross-section by standard ultramicrotomy. Resulting contraction in parallel to the film surface has led to distortions in apparent magnification. The scale bars shown are calibrated for the direction normal to the film surface only.

Profil Penyakit Malaria Di Rumah Sakit Islam Siti Rahmah Padang Tahun 2018

2020 ◽  
Vol 2 (2) ◽  
pp. 08-15
Author(s):  
Rahma Triyana ◽  
Salmi Salmi
Keyword(s):  
Observational Study ◽  
Frequency Distribution ◽  
Cross Section ◽  
Laboratory Tests ◽  
Age Group ◽  
Normal Range ◽  
Cross Sectional ◽  
West Sumatra ◽  
Severity Of The Disease

Malaria is one of the health problems in Indonesia, especially West Sumatra. Determination of the description of Malaria disease in an area is needed to determine the spread and severity of the disease. This study aims to determine the frequency distribution according to age, sex and place of residence, description of the types of Plasmodium causes of Malaria and hematological features in Malaria patients at Siti Rahmah Padang Hospital in 2018. This type of research is a descriptive observational study with an approach or design cross section (cross sectional). The frequency distribution of Malaria sufferers in Siti Rahmah Padang Hospital in 2018 according to the highest age was in the age group 21-30 years as many as 28 cases (36.8%), the highest sex among men was 46 (60.5%) and the highest number of residences was found in Koto Tangah sub-district there were 31 cases (40.8%). The type of Plasmodium found in Malaria cases in Siti Rahmah Padang Hospital in 2018 was P. vivax (73 cases (96.05%)) and P. falciparum (3 cases (3.95%)). The results of laboratory tests on Hb, hematocrit, platelet and leukocyte levels in Malaria positive patients in Siti Rahmah Padang Hospital in 2018 were in the normal range.

Profil Penyakit Malaria di Rumah Sakit Islam Siti Rahmah Padang Tahun 2018

2020 ◽  
Vol 2 (2) ◽  
pp. 08-15
Author(s):  
Rahma Triyana Y ◽  
Salmi Salmi
Keyword(s):  
Observational Study ◽  
Frequency Distribution ◽  
Cross Section ◽  
Laboratory Tests ◽  
Age Group ◽  
Normal Range ◽  
Cross Sectional ◽  
West Sumatra ◽  
Severity Of The Disease

Malaria is one of the health problems in Indonesia, especially West Sumatra. Determination of the description of Malaria disease in an area is needed to determine the spread and severity of the disease. This study aims to determine the frequency distribution according to age, sex and place of residence, description of the types of Plasmodium causes of Malaria and hematological features in Malaria patients at Siti Rahmah Padang Hospital in 2018. This type of research is a descriptive observational study with an approach or design cross section (cross sectional). The frequency distribution of Malaria sufferers in Siti Rahmah Padang Hospital in 2018 according to the highest age was in the age group 21-30 years as many as 28 cases (36.8%), the highest sex among men was 46 (60.5%) and the highest number of residences was found in Koto Tangah sub-district there were 31 cases (40.8%). The type of Plasmodium found in Malaria cases in Siti Rahmah Padang Hospital in 2018 was P. vivax (73 cases (96.05%)) and P. falciparum (3 cases (3.95%)). The results of laboratory tests on Hb, hematocrit, platelet and leukocyte levels in Malaria positive patients in Siti Rahmah Padang Hospital in 2018 were in the normal range.

Access of Key Population to Available HIV and TB Services in Nepal: A Cross Section Study

2019 ◽  
Vol 17 (1) ◽  
pp. 17-23
Author(s):  
B.B. Subba ◽  
N. Rimal ◽  
B.M. Shrestha
Keyword(s):  
Viral Load ◽  
Cross Section ◽  
General Knowledge ◽  
Cross Sectional Survey ◽  
Cross Sectional ◽  
Key Population ◽  
Mdr Tb ◽  
Study Population ◽  
Control And Management ◽  
Structured Questionnaire

Introduction: TB is considered one of the opportunistic infection among PLHIV. The increasing burden of HIV/TB co-infection among key population cause problem to maintain adherence to ART and DOTS services. The emergence of MDR-TB is one of the greatest challenge to control and management of both diseases. However, having knowledge and information of both diseases are important role to access the available HIV/TB services. Methods: A cross-sectional survey was conducted among key population who had HIV/TB co-infection in two-epidemic zone of Nepal. A pretested semi-structured questionnaire was used to collect data. ANOVA test was done to analyze the collected data by using SPSS version 20.0. Results: A total of 343 HIV/TB co-infected individuals were enrolled to the study. Most of participants were from ART and DOTS clients. Therefore, the study found that there was significance difference found between knowledge about TB (F=4.400, p= 0.005), causative agent of TB (F=3.160, p=0.025), risk of TB illness among PLHIV (F=8.491, p=0.001) and among key affected population. Moreover, there was significance difference found between access to OI treatment (F=5.113, p=0.002) and access to viral load (F=4.642, p=0.003) among key study population. In gender perspective, there was no significance difference to use and access to available HIV/TB services. Conclusion: The general knowledge on HIV/TB co-infection was significant association with key population. The knowledge on HIV/TB and access to NGOs’ help can significant effect to access the available HIV and TB services.

Automated Diagonal Slice and View Solution for 3D Device Structure Analysis

2018 ◽  
Author(s):  
Sang Hoon Lee ◽  
Jeff Blackwood ◽  
Stacey Stone ◽  
Michael Schmidt ◽  
Mark Williamson ◽  
...  
Keyword(s):  
Cross Section ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Image Data ◽  
Planar Surface ◽  
Device Structure ◽  
Cross Sectional ◽  
Device Structures ◽  
The Cross ◽  
Planar Analysis

Abstract The cross-sectional and planar analysis of current generation 3D device structures can be analyzed using a single Focused Ion Beam (FIB) mill. This is achieved using a diagonal milling technique that exposes a multilayer planar surface as well as the cross-section. this provides image data allowing for an efficient method to monitor the fabrication process and find device design errors. This process saves tremendous sample-to-data time, decreasing it from days to hours while still providing precise defect and structure data.

Site-Specific Low Angle Plasma FIB Milling for Cross-Sectional Electrical Characterization

2019 ◽  
Author(s):  
Chuan Zhang ◽  
Jane Y. Li ◽  
John Aguada ◽  
Howard Marks
Keyword(s):  
Cross Section ◽  
Focused Ion Beam ◽  
Electrical Characteristic ◽  
Preparation Method ◽  
Ion Beam ◽  
Grazing Angle ◽  
Electrical Characterization ◽  
Sample Preparation Method ◽  
Cross Sectional ◽  
Site Specific

Abstract This paper introduces a novel sample preparation method using plasma focused ion-beam (pFIB) milling at low grazing angle. Efficient and high precision preparation of site-specific cross-sectional samples with minimal alternation of device parameters can be achieved with this method. It offers the capability of acquiring a range of electrical characteristic signals from specific sites on the cross-section of devices, including imaging of junctions, Fins in the FinFETs and electrical probing of interconnect metal traces.

Alternating Plane-View and Cross-Section Scanning Capacitance Microscope Technique to Reveal Various Implant Issue

2007 ◽  
Author(s):  
Tsan-Chang Chuang ◽  
Cha-Ming Shen ◽  
Shi-Chen Lin ◽  
Chen-May Huang ◽  
Jin-Hong Chou ◽  
...  
Keyword(s):  
Cross Section ◽  
Scanning Probe Microscopy ◽  
Dopant Concentration ◽  
Scanning Probe ◽  
Correct Selection ◽  
Cross Sectional ◽  
Root Cause ◽  
Excellent Spatial Resolution ◽  
Microscope Technique ◽  
Plane View

Abstract Scanning capacitance microscopy (SCM) is a 2-D carrier and/or dopant concentration profiling technique under development that utilizes the excellent spatial resolution of scanning probe microscopy. However, PV-SCM has limited capability to achieve the goal due to inherent "plane" trait. On top of that, deeper concentration profile just like deep N-well is also one of restrictions to use. For representing above contents more clearly, this paper presents a few cases that demonstrate the alternated and optimized application of PV-SCM and X-SCM. The case studies concern Joint Test Action Group failure and stand-by failure. These cases illustrate that the correct selection from either plane-view or cross-sectional SCM analysis according to the surrounding of defect could help to exactly and rapidly diagnose the failure mechanism. Alternating and optimizing PV-SCM and X-SCM techniques to navigate various implant issue could provide corrective actions that suit local circumstance of defects and identify the root cause.

Sign in / Sign up

Export Citation Format

Share Document