On Separation of a Divergent Flow at Moderate Reynolds Numbers

1976 ◽  
Vol 43 (2) ◽  
pp. 227-231 ◽  
Author(s):  
Yuji Matsuzaki ◽  
Yuan-Cheng Fung

Flow separation in a divergent channel was investigated in connection with problems of instability and oscillations in physiology at a Reynolds number range much smaller than that usually considered in engineering diffuser design. Experimental data on a divergent flow through a two-dimensional water tunnel in the Reynolds number range Re = 1000 to 6000 are presented. The quantities measured are flow rate, divergence angle, and mean pressure differential between two fixed points at the throat and downstream. In a lower range of divergence angle flow separation is characterized by a sharp decrease in the mean pressure differential when the flow rate is increased continuously and gradually; whereas recovery from separation is signaled by a discontinuous increase in pressure when the flow rate is decreased again. The critical Reynolds numbers for separation and reattachment are detectably different. Some discussion is given about flow separation in external and internal flows.

1992 ◽  
Vol 114 (2) ◽  
pp. 170-177 ◽  
Author(s):  
Y. C. Leung ◽  
N. W. M. Ko ◽  
K. M. Tang

Measurements of the mean pressure distributions and Strouhal numbers on partially grooved cylinders with different groove subtend angles were made over a Reynolds number range of 2.0×104 to 1.3×105 which was within the subcritical regime of smooth cylinder. The Strouhal number, pressure distributions, and their respective coefficients were found to be a function of the groove subtend angles. In general, a progressive shift of the flow regime to lower Reynolds number was observed with higher subtend angle and a subtend angle of 75 deg was found for optimum drag reduction. With the configuration of asymmetrical groove surface, lower drag, and higher lift coefficients were obtained within the same Reynolds number range. Wake traverse and boundary layer results of the asymmetric grooved cylinder indicated that the flows at the smooth and groove surfaces lied within different flow regimes and a downward shift of the wake.


1971 ◽  
Vol 45 (1) ◽  
pp. 203-208 ◽  
Author(s):  
D. J. Tritton

A discussion is given of the current state of knowledge of vortex streets behind circular cylinders in the Reynolds number range 50 to 160. This was prompted by Gaster's (1969) report that he could not find the transition at a Reynolds number of about 90 observed by Tritton (1959) and Berger (1964a). A further brief experiment confirming the existence of the transition is described Reasons for rejecting Gaster's interpretation are advanced. Possible (mutually alternative) explanations of the discrepant observations are suggested.


2013 ◽  
Vol 719 ◽  
pp. 97-128 ◽  
Author(s):  
H. Lee ◽  
K. Hourigan ◽  
M. C. Thompson

AbstractA combined numerical and experimental study examining vortex-induced vibration (VIV) of a neutrally buoyant tethered sphere has been undertaken. The study covered the Reynolds-number range $50\leq \mathit{Re}\lesssim 12\hspace{0.167em} 000$, with the numerical ($50\leq \mathit{Re}\leq 800$) and experimental ($370\leqslant \mathit{Re}\lesssim 12\hspace{0.167em} 000$) ranges overlapping. Neutral buoyancy was chosen to eliminate one parameter, i.e. the influence of gravity, on the VIV behaviour, although, of course, the effect of added mass remains. The tether length was also chosen to be sufficiently long so that, to a good approximation, the sphere was constrained to move within a plane. Seven broad but relatively distinct sphere oscillation and wake states could be distinguished. For regime I, the wake is steady and axisymmetric, and it undergoes transition to a steady two-tailed wake in regime II at $\mathit{Re}= 210$. Those regimes are directly analogous to those of a fixed sphere. Once the sphere begins to vibrate at $\mathit{Re}\simeq 270$ in regime III, the wake behaviour is distinct from the fixed-sphere wake. Initially the vibration frequency of the sphere is half the shedding frequency in the wake, with the latter consistent with the fixed-sphere wake frequency. The sphere vibration is not purely periodic but modulated over several base periods. However, at slightly higher Reynolds numbers ($\mathit{Re}\simeq 280$), planar symmetry is broken, and the vibration shifts to the planar normal (or azimuthal) direction, and becomes completely azimuthal at the start of regime IV at $\mathit{Re}= 300$. In comparison, for a fixed sphere, planar symmetry is broken at a much higher Reynolds number of $\mathit{Re}\simeq 375$. Interestingly, planar symmetry returns to the wake for $\mathit{Re}\gt 330$, in regime V, for which the oscillations are again radial, and is maintained until $\mathit{Re}= 450$ or higher. At the same time, the characteristic vortex loops in the wake become symmetrical, i.e. two-sided. For $\mathit{Re}\gt 500$, in regime VI, the trajectory of the sphere becomes irregular, possibly chaotic. That state is maintained over the remaining Reynolds-number range simulated numerically ($\mathit{Re}\leq 800$). Experiments overlapping this Reynolds-number range confirm the amplitude radial oscillations in regime V and the chaotic wandering for regime VI. At still higher Reynolds numbers of $\mathit{Re}\gt 3000$, in regime VII, the trajectories evolve to quasi-circular orbits about the neutral point, with the orbital radius increasing as the Reynolds number is increased. At $\mathit{Re}= 12\hspace{0.167em} 000$, the orbital diameter reaches approximately one sphere diameter. Of interest, this transition sequence is distinct from that for a vertically tethered heavy sphere, which undergoes transition to quasi-circular orbits beyond $\mathit{Re}= 500$.


1993 ◽  
Vol 115 (1) ◽  
pp. 31-39 ◽  
Author(s):  
J. R. Chaplin

Measurements of pressures around a circular cylinder with fine surface roughness in planar oscillatory flow reveal considerable changes in drag and inertia coefficients over the Reynolds number range 2.5 × 105 to 7.5 × 105, and at Keulegan-Carpenter numbers between 5 and 25. In most respects, these results are shown to be compatible with previous measurements in planar oscillatory flow, and with previous measurements in which the same 0.5-m-dia cylinder was tested in waves.


2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Jie Li ◽  
Clement Kleinstreuer

Employing a validated computer simulation model, entropy generation is analyzed in trapezoidal microchannels for steady laminar flow of pure water and CuO-water nanofluids. Focusing on microchannel heat sink applications, local and volumetric entropy rates caused by frictional and thermal effects are computed for different coolants, inlet temperatures, Reynolds numbers, and channel aspect ratios. It was found that there exists an optimal Reynolds number range to operate the system due to the characteristics of the two different entropy sources, both related to the inlet Reynolds number. Microchannels with high aspect ratios have a lower suitable operational Reynolds number range. The employment of nanofluids can further minimize entropy generation because of their superior thermal properties. Heat transfer induced entropy generation is dominant for typical microheating systems while frictional entropy generation becomes more and more important with the increase in fluid inlet velocity/Reynolds number.


Author(s):  
Zoltan Farago ◽  
Norman Chigier

Experiments using high speed, high magnification, and high contrast photography on airblast coaxial atomizers were carried out to study the wave characteristics of liquid surfaces, ligament breakup, and droplet formation. Liquid flow rate was changed from 4 to 50 kg/h, corresponding to a velocity range of 1.5 to 18 m/s, and a Reynolds number range of 1400 to 18000. Air flow rate was varied from 8 to 70 kg/h, corresponding to a velocity range of 22 to 180 m/s, and a Reynolds number range of 13000 to 105000. Tube wall thicknesses of 145 and 320 microns were used. Under different flow conditions, different jet instabilities (capillary, helical and Kelvin-Helmholtz) and different dominant mechanisms of ligament formation were observed. One of the most surprising experimental results is that, under certain flow conditions, the coaxial round liquid jet, surrounded by an axisymmetric annular air stream, forms a flat curling liquid sheet. This liquid sheet breaks into droplet clouds with a frequency of a few thousand Hertz and emits strong oscillations and fluctuating, highly non-axisymmetric vibrations.


2004 ◽  
Vol 126 (3) ◽  
pp. 362-374 ◽  
Author(s):  
G. Biswas ◽  
M. Breuer ◽  
F. Durst

This paper is concerned with the behavior of flows over a backward-facing step geometry for various expansion ratios H/h=1.9423, 2.5 and 3.0. A literature survey was carried out and it was found that the flow shows a strong two-dimensional behavior, on the plane of symmetry, for Reynolds numbers ReD=ρUbD/μ below approximately 400 (Ub=bulk velocity and D=hydraulic diameter). In this Reynolds number range, two-dimensional predictions were carried out to provide information on the general integral properties of backward-facing step flows, on mean velocity distributions and streamlines. Information on characteristic flow patterns is provided for a wide Reynolds number range, 10−4⩽ReD⩽800. In the limiting case of ReD→0, a sequence of Moffatt eddies of decreasing size and intensity is verified to exist in the concave corner also at ReD=1. The irreversible pressure losses are determined for various Reynolds numbers as a function of the expansion ratio. The two-dimensional simulations are known to underpredict the primary reattachment length for Reynolds numbers beyond which the actual flow is observed to be three-dimensional. The spatial evolution of jet-like flows in both the streamwise and the spanwise direction and transition to three-dimensionality were studied at a Reynolds number ReD=648. This three-dimensional analysis with the same geometry and flow conditions as reported by Armaly et al. (1983) reveals the formation of wall jets at the side wall within the separating shear layer. The wall jets formed by the spanwise component of the velocity move towards the symmetry plane of the channel. A self-similar wall-jet profile emerges at different spanwise locations starting with the vicinity of the side wall. These results complement information on backward-facing step flows that is available in the literature.


1965 ◽  
Vol 180 (1) ◽  
pp. 331-356 ◽  
Author(s):  
L. J. Kastner ◽  
J. C. McVeigh

In view of the importance of accurate measurement of flow rate at low Reynolds numbers, there have been numerous attempts to develop metering devices having constant discharge coefficients in the range of pipe Reynolds numbers between about 3000 and 200 and even below this latter value, and some of these attempts have achieved a reasonable degrees of success. Nevertheless, some confusion exists regarding the dimensions and range of utility of certain designs which have been recommended and further information is necessary in order that the situation may be clarified. The aims of the present investigation, which is believed to be wider in scope than any published in this field in recent years, were to review and correlate existing knowledge and to make an experimental study of the properties of various types of orifice in the low range of Reynolds numbers. Arising from this it was hoped that a design might be evolved which not only had a satisfactorily constant discharge coefficient throughout the range but was also simple to manufacture and reproduce, even for small orifice diameters of the order of 0.5 in or less, and it is believed that some success in attaining this aim was achieved. The first section of the paper contains a review of previous investigations classified into three main groups. In the second part of the paper, experiments with various types of orifice plate are described and it is shown that a properly proportioned single-bevelled orifice has as good a performance in the low Reynolds number range as that of any of the more complicated shapes.


Author(s):  
Tilman Schröder ◽  
Sebastian Schuster ◽  
Dieter Brillert

The designers of radial turbomachinery need detailed information on the impact of the side chamber flow on axial thrust and torque. A previous paper investigated centripetal flow through narrow rotor–stator cavities and compared axial thrust, rotor torque and radial pressure distribution to the case without through-flow. Consequently, this paper extends the investigated range to centrifugal through-flow as it may occur in the hub side chamber of radial turbomachinery. The chosen operating conditions are representative of high-pressure centrifugal compressors used in, for example, carbon capture and storage applications as well as hydrogen compression. To date, only the Reynolds number range up to Re=2·107 has been investigated for centrifugal through-flow. This paper extends the range to Reynolds numbers of Re=2·108 and reports results of experimental and numerical investigations. It focuses on the radial pressure distribution in the rotor–stator cavity and shows the influence of the Reynolds number, cavity width and centrifugal mass flow rate. It therefore extends the range of available valid data that can be used to design radial turbomachinery. Additionally, this analysis compares the results to data and models from scientific literature, showing that in the higher Reynolds number range, a new correlation is required. Finally, the analysis of velocity profiles and wall shear delineates the switch from purely radial outflow in the cavity to outflow on the rotor and inflow on the stator at high Reynolds numbers in comparison to the results reported by others for Reynolds numbers up to Re=2·107.


Sign in / Sign up

Export Citation Format

Share Document