Application of the Helmholtz Integral in Acoustics

1986 ◽  
Vol 108 (4) ◽  
pp. 447-453 ◽  
Author(s):  
M. A. Latcha ◽  
A. Akay
Keyword(s):  
Acoustic Radiation ◽  
Surface Element ◽  
Sound Power ◽  
Acoustic Response ◽  
Element Size ◽  
Radiated Sound ◽  
Radiated Sound Power ◽  
Helmholtz Integral

The solution of an isoparametric, overdetermined formulation of the Helmholtz Integral is presented and demonstrated in three examples of acoustic radiation from spherical sources. The placement of the interior, overdetermining points is discussed and guidelines concerning surface element size are developed and tested. The total radiated sound power and transient acoustic response of a dilating sphere are computed.

Acoustic Radiation Simulation of Marine Sliding-Thrust Bearing Shell Based on SYSNOISE

2011 ◽  
Vol 291-294 ◽  
pp. 1961-1964
Author(s):  
Guang Liang Zhao
Keyword(s):  
Dynamic Analysis ◽  
Boundary Element ◽  
Thrust Bearing ◽  
Acoustic Radiation ◽  
Element Model ◽  
Sound Power ◽  
Supporting Structure ◽  
Radiated Sound ◽  
The Impact ◽  
Radiated Sound Power

This paper takes marine Kingsbury sliding thrust bearing as the research object and conducts the finite element dynamic analysis with the aid of ANSYS software. On this basis, the acoustic boundary element model of a sliding thrust bearing shell is established with the ANSYS dynamic analysis results as the boundary excitation conditions. Besides, the radiated sound power of the shell is calculated by indirect boundary element method in SYNOSISE software. The influence of different condition parameters on the radiated sound power of the shell is perceived through the analysis of several rotation-thrust conditions. As for the special structure of this kind of sliding-thrust bearing, this paper states the impact of the supporting structure performance parameters, the pad number and damp of shell on the shell radiated sound power. The optimized measure for the supporting structure and the plan concerning the pad number’s selection lays the theoretical basis for damping and noise-reducing research on marine sliding-thrust bearing and its rotor system.

A compact active structural acoustic control method for minimizing radiated sound power

2021 ◽  
Vol 263 (3) ◽  
pp. 3396-3406
Author(s):  
Scott Sommerfeldt
Keyword(s):  
Control Method ◽  
Acoustic Radiation ◽  
Structural Vibration ◽  
Sound Power ◽  
Flat Plates ◽  
Spatial Gradients ◽  
Acoustic Control ◽  
Radiated Sound ◽  
Radiated Sound Power ◽  
Structural Acoustic Control

Active structural acoustic control is an active control method that controls a vibrating structure in a manner that reduces the sound power radiated from the structure. Such methods focus on attenuating some metric that results in attenuated sound power, while not necessarily minimizing the structural vibration. The work reported here outlines the weighted sum of spatial gradients (WSSG) control metric as a method to attenuate structural radiation. The WSSG method utilizes a compact error sensor that is able to measure the acceleration and the acceleration gradients at the sensor location. These vibration signals are combined into the WSSG metric in a manner that is closely related to the radiated sound power, such that minimizing the WSSG also results in a minimization of the sound power. The connection between WSSG and acoustic radiation modes will be highlighted. Computational and experimental results for both flat plates and cylindrical shells will be presented, indicating that the WSSG method can achieve near optimal attenuation of the radiated sound power with a minimum number of sensors.

Quieting Plate Modes With Optimally Sized Point Masses: A Volume Velocity Approach

1995 ◽  
Author(s):  
Hans-Walter Wodtke ◽  
Gary H. Koopmann
Keyword(s):  
Acoustic Radiation ◽  
Sound Intensity ◽  
Structural Vibration ◽  
Acoustic Response ◽  
Radiation Problem ◽  
Volume Velocity ◽  
Intensity Measurements ◽  
Radiated Sound ◽  
The Masses ◽  
Radiated Sound Power

Abstract The radiated sound power of the second symmetric mode of a clamped square plate is minimized by attaching optimally sized point masses to the plate. The plate is driven by a point force at its center and the positions of the masses are prescribed. The structural vibration problem is solved using a simple Rayleigh-Ritz approach. Solving the acoustic radiation problem is simplified by making a low-ka-assumption, i.e., the point masses are determined so as to minimize the surface volume velocity of the plate. The predicted results are verified experimentally by means of sound intensity measurements. It is shown that a structural resonance can be deleted from the acoustic response by exploiting volume velocity cancellation. The effects involved are illustrated in detail.

ENFORCING RECIPROCITY IN NUMERICAL ANALYSIS OF ACOUSTIC RADIATION MODES AND SOUND POWER EVALUATION

2012 ◽  
Vol 20 (03) ◽  
pp. 1250005 ◽  
Author(s):  
HERWIG PETERS ◽  
NICOLE KESSISSOGLOU ◽  
STEFFEN MARBURG
Keyword(s):  
Boundary Element Method ◽  
Boundary Element ◽  
Acoustic Radiation ◽  
Sound Power ◽  
Impedance Matrix ◽  
Radiated Sound ◽  
The Asymmetry ◽  
Power Evaluation ◽  
Radiated Sound Power ◽  
Element Method

By identifying the efficiently radiating acoustic radiation modes of a fluid loaded vibrating structure, the storage requirements of the acoustic impedance matrix for calculation of the sound power using the boundary element method can be greatly reduced. In order to compute the acoustic radiation modes, the impedance matrix needs to be symmetric. However, when using the boundary element method, it is often found that the impedance matrix is not symmetric. This paper describes the origin of the asymmetry of the impedance matrix and presents a simple way to generate symmetry. The introduction of additional errors when symmetrizing the impedance matrix must be avoided. An example is used to demonstrate the behavior of the asymmetry and the effect of symmetrization of the impedance matrix on the sound power. The application of the technique presented in this work to compute the radiated sound power of a submerged marine vessel is discussed.

A method to compute the radiated sound power based on mapped acoustic radiation modes

2014 ◽  
Vol 135 (2) ◽  
pp. 679-692 ◽  
Author(s):  
Haijun Wu ◽  
Weikang Jiang ◽  
Yilin Zhang ◽  
Wenbo Lu
Keyword(s):  
Acoustic Radiation ◽  
Sound Power ◽  
Radiated Sound ◽  
Radiated Sound Power

A Study on Relevance between Distortion of Distributed Mode Loudspeaker and Characteristic of Sound Panel

2011 ◽  
Vol 291-294 ◽  
pp. 2105-2110
Author(s):  
Liang Jin Luo
Keyword(s):  
Vibration Frequency ◽  
Sandwich Panel ◽  
Flexural Vibration ◽  
Sound Power ◽  
Impedance Matrix ◽  
Cell Ratio ◽  
Radiated Sound ◽  
Sound Sensitivity ◽  
The Relationship ◽  
Radiated Sound Power

From flat-plate flexural vibration and radiated sound power discussed the inherent relationship between panel vibration frequency of distributed mode loudspeaker and geometric parameters, impedance matrix of soundboard and studied the relationship between soundboard structure of polyester foam sandwich panel and distortion of loudspeaker. Experimental results showed that distortion increases as the cell size and compress modulus, cell ratio, cell open ratio and thickness increases, but the sound sensitivity decreases as the compress modulus increases.

scholarly journals FE-BE computation of electromagnetic noise of a permanent-magnetic excited synchronous ma-chine considering dynamic rotor eccentricity

2018 ◽  
Vol 211 ◽  
pp. 18005
Author(s):  
Marcel Clappier ◽  
Lothar Gaul
Keyword(s):  
Sound Power ◽  
Fe Model ◽  
Electromagnetic Noise ◽  
Structural Dynamic ◽  
Magnetic Forces ◽  
Rotor Eccentricity ◽  
Resonance Frequencies ◽  
Radiated Sound ◽  
Run Up ◽  
Radiated Sound Power

Electromagnetic noise in Electrical Machines (EMs) occurs due to vibrations caused by magnetic forces acting onto rotor and stator surface. This is the dominant source for the considered permanent-magnetic excited synchronous machine in this paper. The radiated electromagnetic noise is sequentially calculated by a Finite Element (FE) and Boundary Element (BE) computation. An electromagnetic FE model is created to determine magnetic forces. Structure-borne sound and rotor dynamics are calculated using a structural dynamic FE model for the EM housing and the rotor. In order to predict resonance frequencies and amplitudes as reliable as possible, it is important to know the direction-dependent stiffness of the laminated rotor stacks and mechanical joints as well as their structural damping. Thereby, the properties of the laminated stack can be determined experimentally by a shear and dilatation test. Mechanical joint properties can be modelled by Thin-Layer Elements (TLEs) and the overall damping by the model of constant hysteretic damping. The radiated sound power is determined by a direct BE computation. The influence of dynamic rotor eccentricity on radiated sound power is examined for a run-up of the EM. All FE models are verified by data from experimental modal analysis.

Passive and Active Control of the Radiated Sound Power from a Submarine Excited by Propeller Forces

2013 ◽  
Vol 57 (1) ◽  
pp. 59-71 ◽  
Author(s):  
Sascha Merz ◽  
Nicole Kessissoglou ◽  
Roger Kinns ◽  
Steffen Marburg
Keyword(s):  
Active Control ◽  
Sound Power ◽  
Radiated Sound ◽  
Radiated Sound Power
Sign in / Sign up

Export Citation Format

Share Document