Free Vibration of Polar-Orthotropic Sector Plates Resting on Point Supports

1985 ◽  
Vol 107 (3) ◽  
pp. 334-338 ◽  
Author(s):  
Y. Narita
Keyword(s):  
Power Series ◽  
Free Vibration ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Opening Angle ◽  
Simply Supported ◽  
Annular Sector ◽  
Sector Plate ◽  
Polar Orthotropic ◽  
Double Power Series

An accurate Ritz solution for the free vibration of point-supported annular sector plates of polar orthotropy is presented. A double power series function is used to represent deflection of the plate, with Lagrange multipliers to impose the constraint conditions. To establish accuracy of the approach, the frequency parameters of a sector plate with some supporting points distributed along the boundary are compared to those of a uniformly simply supported plate. The natural frequencies and mode shapes are presented for wide ranges of the opening angle, radius ratio, and orthotropic parameters.

scholarly journals Effects of Elliptical Hole on the Correlation of Natural Frequency with Buckling Load of Basalt Laminates Composite Plates

2020 ◽  
Vol 27 (1) ◽  
pp. 216-225
Author(s):  
Buntheng Chhorn ◽  
WooYoung Jung
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Basalt Fiber ◽  
Orientation Angle ◽  
Elliptical Hole ◽  
Composite Plates ◽  
Buckling Load ◽  
Mode Shapes ◽  
Geometric Ratio

AbstractRecently, basalt fiber reinforced polymer (BFRP) is acknowledged as an outstanding material for the strengthening of existing concrete structure, especially it was being used in marine vehicles, aerospace, automotive and nuclear engineering. Most of the structures were subjected to severe dynamic loading during their service life that may induce vibration of the structures. However, free vibration studied on the basalt laminates composite plates with elliptical cut-out and correlation of natural frequency with buckling load has been very limited. Therefore, effects of the elliptical hole on the natural frequency of basalt/epoxy composite plates was performed in this study. Effects of stacking sequence (θ), elliptical hole inclination (ϕ), hole geometric ratio (a/b) and position of the elliptical hole were considered. The numerical modeling of free vibration analysis was based on the mechanical properties of BFRP obtained from the experiment. The natural frequencies as well as mode shapes of basalt laminates composite plates were numerically determined using the commercial program software (ABAQUS). Then, the determination of correlation of natural frequencies with buckling load was carried out. Results showed that elliptical hole inclination and fiber orientation angle induced the inverse proportion between natural frequency and buckling load.

Vibration of Beams with a Single Delamination under Axial Loading

2011 ◽  
Vol 675-677 ◽  
pp. 477-480
Author(s):  
Dong Wei Shu
Keyword(s):  
Free Vibration ◽  
Natural Frequency ◽  
Analytical Solutions ◽  
Axial Load ◽  
Natural Frequencies ◽  
Axial Loading ◽  
Composite Beams ◽  
Mode Shapes ◽  
Equilibrium Conditions ◽  
Monotonic Relation

In this work analytical solutions are developed to study the free vibration of composite beams under axial loading. The beam with a single delamination is modeled as four interconnected Euler-Bernoulli beams using the delamination as their boundary. The continuity and the equilibrium conditions are satisfied between the adjoining beams. The studies show that the sizes and the locations of the delaminations significantly influence the natural frequencies and mode shapes of the beam. A monotonic relation between the natural frequency and the axial load is predicted.

Dynamic characteristics of horizontally curved bridges

2017 ◽  
Vol 24 (19) ◽  
pp. 4465-4483 ◽  
Author(s):  
Mohsen Amjadian ◽  
Anil K Agrawal
Keyword(s):  
Free Vibration ◽  
Dynamic Characteristics ◽  
Natural Frequencies ◽  
Response Spectrum ◽  
Translational Motion ◽  
Free Vibration Analysis ◽  
Mode Shapes ◽  
Curved Bridges ◽  
Horizontally Curved ◽  
Horizontally Curved Bridges

Horizontally curved bridges have complicated dynamic characteristics because of their irregular geometry and nonuniform mass and stiffness distributions. This paper aims to develop a simplified and practical method for the calculation of the natural frequencies and mode shapes of horizontally curved bridges that would be of interest to bridge engineers for the estimation of the seismic response of these types of bridges. For this purpose, a simple three-degree-of-freedom (3DOF) dynamic model for free vibration equation of this type of bridge has been developed. It is shown that the translational motion of the deck of horizontally curved bridges in the direction that is perpendicular to their axis of symmetry is always coupled with the rotational motion of the deck, regardless of the location of the stiffness center. The model is further exploited to develop closed-form formulas for the estimation of the maximum displacements of the corners of the deck of one-way asymmetric horizontally curved bridges. The accuracy of the model is verified by finite-element model of a horizontally curved bridge prototype in OpenSEES. Finally, the model is utilized to study the influence of the location of the stiffness center with respect to the deck curvature center on the natural frequency and the maximum displacements of the corners of the deck for different curvatures of the deck. The results of free vibration analysis show that the natural frequencies of one-way asymmetric horizontally curved bridges, in general, increase with the increase of the subtended angle of the deck. The results of earthquake response spectrum analysis show that the increase in the subtended angle of one-way asymmetric horizontally curved bridges decreases the radial displacements of the corners of the deck but increases the azimuthal displacement. These two responses both increase with the increase in the distance between the stiffness center and the curvature center.

Free Vibration Analysis of a Carbon Nanotube Reinforced Composite Beam

2014 ◽  
Vol 592-594 ◽  
pp. 2041-2045 ◽  
Author(s):  
B. Naresh ◽  
A. Ananda Babu ◽  
P. Edwin Sudhagar ◽  
A. Anisa Thaslim ◽  
R. Vasudevan
Keyword(s):  
Carbon Nanotube ◽  
Free Vibration ◽  
Composite Beam ◽  
Natural Frequencies ◽  
Equations Of Motion ◽  
Free Vibration Analysis ◽  
Mode Shapes ◽  
Element Formulation ◽  
Reinforced Composite ◽  
Vibration Responses

In this study, free vibration responses of a carbon nanotube reinforced composite beam are investigated. The governing differential equations of motion of a carbon nanotube (CNT) reinforced composite beam are presented in finite element formulation. The validity of the developed formulation is demonstrated by comparing the natural frequencies evaluated using present FEM with those of available literature. Various parametric studies are also performed to investigate the effect of aspect ratio and percentage of CNT content and boundary conditions on natural frequencies and mode shapes of a carbon nanotube reinforced composite beam. It is shown that the addition of carbon nanotube in fiber reinforced composite beam increases the stiffness of the structure and consequently increases the natural frequencies and alter the mode shapes.

Free Vibration of Thin-Walled Open Section Beams With Unconstrained Damping Treatment

1981 ◽  
Vol 48 (1) ◽  
pp. 169-173 ◽  
Author(s):  
S. Narayanan ◽  
J. P. Verma ◽  
A. K. Mallik
Keyword(s):  
Free Vibration ◽  
Cross Section ◽  
Transverse Vibration ◽  
Natural Frequencies ◽  
Vibration Characteristics ◽  
Numerical Results ◽  
Simply Supported ◽  
Clamped Beams ◽  
Thin Walled ◽  
Open Cross Section

Free-vibration characteristics of a thin-walled, open cross-section beam, with unconstrained damping layers at the flanges, are investigated. Both uncoupled transverse vibration and the coupled bending-torsion oscillations, of a beam of a top-hat section, are considered. Numerical results are presented for natural frequencies and modal loss factors of simply supported and clamped-clamped beams.

scholarly journals Phononic Band Gap and Free Vibration Analysis of Fluid-Conveying Pipes with Periodically Varying Cross-Section

2021 ◽  
Vol 11 (21) ◽  
pp. 10485
Author(s):  
Hao Yu ◽  
Feng Liang ◽  
Yu Qian ◽  
Jun-Jie Gong ◽  
Yao Chen ◽  
...  
Keyword(s):  
Free Vibration ◽  
Band Gap ◽  
Cross Section ◽  
Natural Frequencies ◽  
Free Vibration Analysis ◽  
Critical Parameters ◽  
Mode Shapes ◽  
Beam Model ◽  
The Impact ◽  
Fluid Conveying Pipes

Phononic crystals (PCs) are a novel class of artificial periodic structure, and their band gap (BG) attributes provide a new technical approach for vibration reduction in piping systems. In this paper, the vibration suppression performance and natural properties of fluid-conveying pipes with periodically varying cross-section are investigated. The flexural wave equation of substructure pipes is established based on the classical beam model and traveling wave property. The spectral element method (SEM) is developed for semi-analytical solutions, the accuracy of which is confirmed by comparison with the available literature and the widely used transfer matrix method (TMM). The BG distribution and frequency response of the periodic pipe are attained, and the natural frequencies and mode shapes are also obtained. The effects of some critical parameters are discussed. It is revealed that the BG of the present pipe system is fundamentally induced by the geometrical difference of the substructure cross-section, and it is also related to the substructure length and fluid–structure interaction (FSI). The number of cells does not contribute to the BG region, while it has significant effects on the amplitude attenuation, higher order natural frequencies and mode shapes. The impact of FSI is more evident for the pipes with smaller numbers of cells. Moreover, compared with the conventional TMM, the present SEM is demonstrated more effective for comprehensive analysis of BG characteristics and free vibration of PC dynamical structures.

scholarly journals UNCOUPLED VIBRATIONS IN FUNCTIONALLY GRADED TIMOSHENKO BEAM

2016 ◽  
Vol 54 (6) ◽  
pp. 785 ◽  
Author(s):  
Nguyen Tien Khiem ◽  
Nguyen Ngoc Huyen
Keyword(s):  
Free Vibration ◽  
Timoshenko Beam ◽  
Natural Frequencies ◽  
Flexural Vibration ◽  
Functionally Graded ◽  
Mode Shapes ◽  
Power Law Distribution ◽  
Material Parameters ◽  
Flexural Vibrations ◽  
Fgm Beam

Free vibration of FGM Timoshenko beam is investigated on the base of the power law distribution of FGM. Taking into account the actual position of neutral plane enables to obtain general condition for uncoupling of axial and flexural vibrations in FGM beam. This condition defines a class of functionally graded beams for which axial and flexural vibrations are completely uncoupled likely to the homogeneous beams. Natural frequencies and mode shapes of uncoupled flexural vibration of beams from the class are examined in dependence on material parameters and slendernes

scholarly journals Improved Riccati Transfer Matrix Method for Free Vibration of Non-Cylindrical Helical Springs Including Warping

2012 ◽  
Vol 19 (6) ◽  
pp. 1167-1180 ◽  
Author(s):  
A.M. Yu ◽  
Y. Hao
Keyword(s):  
Free Vibration ◽  
Transfer Matrix ◽  
Transfer Matrix Method ◽  
Matrix Method ◽  
Natural Frequencies ◽  
Free Vibration Analysis ◽  
Mode Shapes ◽  
Axial Deformation ◽  
Cross Sectional ◽  
Helical Springs

Free vibration equations for non-cylindrical (conical, barrel, and hyperboloidal types) helical springs with noncircular cross-sections, which consist of 14 first-order ordinary differential equations with variable coefficients, are theoretically derived using spatially curved beam theory. In the formulation, the warping effect upon natural frequencies and vibrating mode shapes is first studied in addition to including the rotary inertia, the shear and axial deformation influences. The natural frequencies of the springs are determined by the use of improved Riccati transfer matrix method. The element transfer matrix used in the solution is calculated using the Scaling and Squaring method and Pad'e approximations. Three examples are presented for three types of springs with different cross-sectional shapes under clamped-clamped boundary condition. The accuracy of the proposed method has been compared with the FEM results using three-dimensional solid elements (Solid 45) in ANSYS code. Numerical results reveal that the warping effect is more pronounced in the case of non-cylindrical helical springs than that of cylindrical helical springs, which should be taken into consideration in the free vibration analysis of such springs.

Combinations for the Free Vibration Behaviors of Anisotropic Rectangular Plates Under General Edge Conditions

1999 ◽  
Author(s):  
Yoshihiro Narita
Keyword(s):  
Free Vibration ◽  
Structural Design ◽  
Natural Frequencies ◽  
Ritz Method ◽  
Technical Information ◽  
Mode Shapes ◽  
Rectangular Plates ◽  
Plate Models ◽  
Edge Conditions ◽  
Anisotropic Rectangular Plates

Abstract The free vibration behavior of rectangular plates provides important technical information in structural design, and the natural frequencies are primarily affected by the boundary conditions as well as aspect and thickness ratios. One of the three classical edge conditions, i.e., free, simple supported and clamped edges, may be used to model the constraint along an edge of the rectangle. Along the entire boundary with four edges, there exist a wide variety of combinations in the edge conditions, each yielding different natural frequencies and mode shapes. For counting the total number of possible combinations, the present paper introduces the Polya counting theory in combinatorial mathematics, and formulas are derived for counting the exact numbers. A modified Ritz method is then developed to calculate natural frequencies of anisotropic rectangular plates under any combination of the three edge conditions and is used to numerically verify the numbers. In numerical experiments, the number of combinations in the free vibration behaviors is determined for some plate models by using the derived formulas, and are corroborated by counting the numbers of different sets of the natural frequencies that are obtained from the Ritz method.

In-Plane Free Vibration of Uniform Circular Arches Made of Axially Functionally Graded Materials

2019 ◽  
Vol 19 (08) ◽  
pp. 1950084 ◽  
Author(s):  
Joon Kyu Lee ◽  
Byoung Koo Lee
Keyword(s):  
Free Vibration ◽  
Young’S Modulus ◽  
Natural Frequencies ◽  
Dynamic Equilibrium ◽  
Young's Modulus ◽  
Mass Density ◽  
Functionally Graded ◽  
Mode Shapes ◽  
Governing Equations ◽  
Direct Integral

This study focused on the in-plane free vibration of uniform circular arches made of axially functionally graded (AFG) materials. Based on the dynamic equilibrium of an arch element, the governing equations for the free vibration of an AFG arch are derived in this study, where arbitrary functions for the Young’s modulus and mass density are acceptable. For the purpose of numerical analysis, quadratic polynomials for the Young’s modulus and mass density are considered. To calculate the natural frequencies and corresponding mode shapes, the governing equations are solved using the direct integral method enhanced by the trial eigenvalue method. For verification purposes, the predicted frequencies are compared to those obtained by the general purpose software ADINA. A parametric study of the end constraint, rotatory inertia, modular ratio, radius parameter, and subtended angle for the natural frequencies is conducted and the corresponding mode shapes are reported.

Sign in / Sign up

Export Citation Format

Share Document