Height Extrapolation of Wind Data

1985 ◽  
Vol 107 (1) ◽  
pp. 10-14 ◽  
Author(s):  
A. S. Mikhail
Keyword(s):  
Wind Speed ◽  
Power Law ◽  
Wind Data ◽  
Power Law Model ◽  
Short Term ◽  
Shape Factors ◽  
Wind Speeds ◽  
Average Wind ◽  
Modified Power Law

Various models that are used for height extrapolation of short and long-term averaged wind speeds are discussed. Hourly averaged data from three tall meteorological towers (the NOAA Erie Tower in Colorado, the Battelle Goodnoe Hills Tower in Washington, and the WKY-TV Tower in Oklahoma), together with data from 17 candidate sites (selected for possible installation of large WECS), were used to analyze the variability of short-term average wind shear with atmospheric and surface parameters and the variability of the long-term Weibull distribution parameter with height. The exponents of a power-law model, fit to the wind speed profiles at the three meteorological towers, showed the same variability with anemometer level wind speed, stability, and surface roughness as the similarity law model. Of the four models representing short-term wind data extrapolation with height (1/7 power law, logarithmic law, power law, and modified power law), the modified power law gives the minimum rms for all candidate sites for short-term average wind speeds and the mean cube of the speed. The modified power-law model was also able to predict the upper-level scale factor for the WKY-TV and Goodnoe Hills Tower data with greater accuracy. All models were not successful in extrapolation of the Weibull shape factors.

scholarly journals Evaluation of the Technical Wind Energy Potential of Kisii Region Based on the Weibull and Rayleigh Distribution Models

2018 ◽  
Author(s):  
Laban N. Ongaki ◽  
Christopher M. Maghanga ◽  
Joash Kerongo
Keyword(s):  
Wind Speed ◽  
Rayleigh Distribution ◽  
Series Data ◽  
Energy Potential ◽  
Distribution Models ◽  
Wind Speeds ◽  
Average Wind ◽  
Mean Wind Speed ◽  
Wind Energy Potential

The research sought to investigate the long term characteristics of wind in the Kisii region (elevation 1710m above sea level, 0.68oS, 34.79o E). Wind speeds were analyzed and characterized on short term (per month for a year) and then simulated for long term (ten years) measured hourly series data of daily wind speeds at a height of 10m. The analysis included daily wind data which was grouped into discrete data and then calculated to represent; the mean wind speed, diurnal variations, daily variations as well as the monthly variations. The wind speed frequency distribution at the height 10 m was found to be 2.9ms-1 with a standard deviation of 1.5. Based on the two month’s data that was extracted from the AcuRite 01024 Wireless Weather Stations with 5-in-1 Weather Sensor experiments set at three sites in the region, averages of wind speeds at hub heights of 10m and 13m were calculated and found to be 1.7m/s, 2.0m/s for Ikobe station, 2.4m/s, 2.8m/s for Kisii University stations, and 1.3m/s, 1.6m/s for Nyamecheo station respectively. Then extrapolation was done to determine average wind speeds at heights (20m, 30m, 50m, and 70m) which were found to be 85.55W/m2, 181.75W/m2, 470.4W/m2 and 879.9W/m2 respectively. The wind speed data was used statistically to model a Weibull probability density function and used to determine the power density for Kisii region.

scholarly journals A Basic Wind Speed Map for Oman

2014 ◽  
Vol 11 (2) ◽  
pp. 64
Author(s):  
A.S. Alnuaimi ◽  
M.A. Mohsin ◽  
K.H. Al-Riyami
Keyword(s):  
Wind Speed ◽  
Return Period ◽  
Structural Design ◽  
Short Term ◽  
Wind Speed Data ◽  
Wind Speeds ◽  
Mean Wind Speed

The aim of this research was to develop the first basic wind speed map for Oman. Hourly mean wind speed records from 40 metrological stations were used in the calculation. The period of continuous records ranged from 4–37 years. The maximum monthly hourly mean and the maxima annual hourly mean wind speed data were analysed using the Gumbel and Gringorten methods. Both methods gave close results in determining basic wind speeds, with the Gumbel method giving slightly higher values. Due to a lack of long-term records in some regions of Oman, basic wind speeds were extrapolated for some stations with only short-term records, which were defined as those with only 4– 8 years of continuous records; in these cases, monthly maxima were used to predict the long-term basic wind speeds. Accordingly, a basic wind speed map was developed for a 50-year return period. This map was based on basic wind speeds calculated from actual annual maxima records of 29 stations with at least 9 continuous years of records as well as predicted annual maxima wind speeds for 11 short-term record stations. The basic wind speed values ranged from 16 meters/second (m/s) to 31 m/s. The basic wind speed map developed in this research is recommended for use as a guide for structural design in Oman. 

scholarly journals Assessing Wind Data from Reanalyses for the Upper Midwest

2019 ◽  
Vol 58 (3) ◽  
pp. 429-446 ◽  
Author(s):  
Jacob J. Coburn
Keyword(s):  
Wind Speed ◽  
Resource Assessment ◽  
Reanalysis Data ◽  
Wind Data ◽  
Upper Midwest ◽  
Wind Speeds ◽  
Potential Applications ◽  
Mitigate Climate Change ◽  
Wind Resource

AbstractWind is an important atmospheric variable that is receiving increased attention as the world seeks to shift from carbon-based fuels in order to mitigate climate change. This has resulted in increased need for more temporally and spatially continuous wind information, which is often met through the use of reanalysis data. However, limited work has been done to assess the long-term accuracy of the wind data against observations in the context of specific applications. This study focuses on the representation of daily and monthly average 10-m wind speed data in the upper Midwest by six global reanalysis datasets. The accuracy of the datasets was assessed using several measures of skill, as well as the associated wind speed distributions and long-term trends. While it was found that higher resolution and complexity in more recent generations of reanalyses produced more accurate simulations of wind in the region, important biases remained. High variability in the observed data resulted in lower correlations at the monthly time scale. As with previous research, linear trends calculated from the reanalyzed wind speeds were significantly underestimated compared to observed trends. While it is expected that future improvements in model resolution, physics, and data assimilation will further improve wind representation in reanalyses, accounting for the differences between the available datasets and their associated biases will be important for potential applications of the output, particularly wind resource assessment.

scholarly journals Algorithm design for wind prediction in Berakit Bay, Bintan Island using Long Short-Term Memory (LSTM) method

2021 ◽  
Vol 944 (1) ◽  
pp. 012006
Author(s):  
D R Pratama ◽  
I Jaya ◽  
M Iqbal
Keyword(s):  
Wind Speed ◽  
Short Term Memory ◽  
Algorithm Design ◽  
Short Term ◽  
Average Wind Speed ◽  
Term Memory ◽  
Average Wind ◽  
Long Short Term Memory ◽  
System Designs

Abstract Wind speed is a crucial parameter alongside coastal areas, especially Indonesia. Above average wind speed can cause harmful effects on human activities. This study uses wind speed data from Berakit Bay, Bintan Island is a potential location for coastal community settlement, fisheries, and tourist activities. The wind parameter then predicted using the Long Short-Term Memory or LSTM algorithm. This algorithm is able to study long-term dependencies by converting simple nervous system designs into specialized blocks containing cells. It is suitable to be applied to long-term wind predictions where the wind speed at this time is very influential with the wind speed in the future. In preparing the LSTM, the data preprocessing and the architecture used will determine the prediction results. In this study, four different architectures were made in order to determine the most optimal architecture. The results show that the LSTM architecture is able to obtain a relatively good RMSE value of 1.87 and an accuracy of 39.40% with the use of two LSTM layers, 256 units in the first layer and 128 in the second layer. The LSTM algorithm in predicting wind can also be applied to other areas in Indonesia.

SHAPING OF AN AUTONOMOUS POWER SYSTEM FOR GUARANTEED POWER SUPPLY WITH THE PREDOMINANCE WIND ENERGY

2018 ◽  
pp. 28-50
Author(s):  
S. G. Ignatiev ◽  
S. V. Kiseleva
Keyword(s):  
Energy Storage ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Demand ◽  
Diesel Generator ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Optimization of the autonomous wind-diesel plants composition and of their power for guaranteed energy supply, despite the long history of research, the diversity of approaches and methods, is an urgent problem. In this paper, a detailed analysis of the wind energy characteristics is proposed to shape an autonomous power system for a guaranteed power supply with predominance wind energy. The analysis was carried out on the basis of wind speed measurements in the south of the European part of Russia during 8 months at different heights with a discreteness of 10 minutes. As a result, we have obtained a sequence of average daily wind speeds and the sequences constructed by arbitrary variations in the distribution of average daily wind speeds in this interval. These sequences have been used to calculate energy balances in systems (wind turbines + diesel generator + consumer with constant and limited daily energy demand) and (wind turbines + diesel generator + consumer with constant and limited daily energy demand + energy storage). In order to maximize the use of wind energy, the wind turbine integrally for the period in question is assumed to produce the required amount of energy. For the generality of consideration, we have introduced the relative values of the required energy, relative energy produced by the wind turbine and the diesel generator and relative storage capacity by normalizing them to the swept area of the wind wheel. The paper shows the effect of the average wind speed over the period on the energy characteristics of the system (wind turbine + diesel generator + consumer). It was found that the wind turbine energy produced, wind turbine energy used by the consumer, fuel consumption, and fuel economy depend (close to cubic dependence) upon the specified average wind speed. It was found that, for the same system with a limited amount of required energy and high average wind speed over the period, the wind turbines with lower generator power and smaller wind wheel radius use wind energy more efficiently than the wind turbines with higher generator power and larger wind wheel radius at less average wind speed. For the system (wind turbine + diesel generator + energy storage + consumer) with increasing average speed for a given amount of energy required, which in general is covered by the energy production of wind turbines for the period, the maximum size capacity of the storage device decreases. With decreasing the energy storage capacity, the influence of the random nature of the change in wind speed decreases, and at some values of the relative capacity, it can be neglected.

scholarly journals Analysis of Performance of the Wind-Driven Pulverizing Aerator Based on Average Wind Speeds in the Conditions of Góreckie Lake

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2796
Author(s):  
Andrzej Osuch ◽  
Ewa Osuch ◽  
Stanisław Podsiadłowski ◽  
Piotr Rybacki
Keyword(s):  
Mathematical Model ◽  
Wind Speed ◽  
Water Pump ◽  
Average Wind Speed ◽  
Flow Rates ◽  
Wind Speeds ◽  
Average Wind ◽  
Flow Through ◽  
Analysis Of Performance ◽  
Research Period

In the introduction to this paper, the characteristics of Góreckie lake and the construction and operation of the wind-driven pulverizing aerator are presented. The purpose of this manuscript is to determine the efficiency of the pulverizing aerator unit in the windy conditions of Góreckie Lake. The efficiency of the pulverization aerator depends on the wind conditions at the lake. It was necessary to conduct thorough research to determine the efficiency of water flow through the pulverization segment (water pump). It was necessary to determine the rotational speed of the paddle wheel, which depended on the average wind speed. Throughout the research period, measurements of hourly average wind speed were carried out. It was possible to determine the efficiency of the machine by developing a dedicated mathematical model. The latest method was used in the research, consisting of determining the theoretical volumetric flow rates of water in the pulverizing aerator unit, based on average hourly wind speeds. Pulverization efficiency under the conditions of Góreckie Lake was determined based on 6600 average wind speeds for spring, summer and autumn, 2018. Based on the model, the theoretical efficiency of the machine was calculated, which, under the conditions of Góreckie Lake, amounted to 75,000 m3 per year.

Power-law correlations, related models for long-range dependence and their simulation

2000 ◽  
Vol 37 (04) ◽  
pp. 1104-1109 ◽  
Author(s):  
Tilmann Gneiting
Keyword(s):  
Long Range ◽  
Power Law ◽  
Long Memory ◽  
Stationary Time Series ◽  
Long Range Dependence ◽  
Short Term ◽  
Permissible Range ◽  
Simultaneous Fitting ◽  
Straightforward Proof

Martin and Walker ((1997) J. Appl. Prob. 34, 657–670) proposed the power-law ρ(v) = c|v|-β, |v| ≥ 1, as a correlation model for stationary time series with long-memory dependence. A straightforward proof of their conjecture on the permissible range of c is given, and various other models for long-range dependence are discussed. In particular, the Cauchy family ρ(v) = (1 + |v/c|α)-β/α allows for the simultaneous fitting of both the long-term and short-term correlation structure within a simple analytical model. The note closes with hints at the fast and exact simulation of fractional Gaussian noise and related processes.

scholarly journals Formation and distribution of sea-surface microlayers

2010 ◽  
Vol 7 (4) ◽  
pp. 5719-5755 ◽  
Author(s):  
O. Wurl ◽  
E. Wurl ◽  
L. Miller ◽  
K. Johnson ◽  
S. Vagle
Keyword(s):  
Wind Speed ◽  
Primary Production ◽  
Sea Surface ◽  
Surface Microlayer ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind ◽  
The Pacific ◽  
Sea Surface Microlayer ◽  
Natural Surfactants

Abstract. Results from a study of surfactants in the sea-surface microlayer (SML) in different regions of the ocean (subtropical, temperate, polar) suggest that this interfacial layer between the ocean and atmosphere covers the ocean's surface to a significant extent. Threshold values at which primary production acts as a significant source of natural surfactants have been derived from the enrichment of surfactants in the SML relative to underlying water and local primary production. Similarly, we have also derived a wind speed threshold at which the SML is disrupted. The results suggest that surfactant enrichment in the SML is typically greater in oligotrophic regions of the ocean than in more productive waters. Furthermore, the enrichment of surfactants persisted at wind speeds of up to 10 m s−1 without any observed depletion above 5 m s−1. This suggests that the SML is stable enough to exist even at the global average wind speed of 6.6 m s−1. Global maps of primary production and wind speed are used to estimate the ocean's SML coverage. The maps indicate that wide regions of the Pacific and Atlantic Oceans between 30° N and 30° S are more significantly affected by the SML than northern of 30° N and southern of 30° S due to higher productivity (spring/summer blooms) and wind speeds exceeding 12 m s−1 respectively.

scholarly journals Artificial Intelligence Techniques for Estimation of Optimum Weibull Parameters for Wind Speed Distribution

2019 ◽  
Vol 8 (4S2) ◽  
pp. 150-156
Keyword(s):  
Wind Speed ◽  
Tamil Nadu ◽  
Optimization Algorithms ◽  
Coefficient Of Determination ◽  
Short Term ◽  
Weibull Parameters ◽  
Wind Speed Data ◽  
Speed Distribution ◽  
Wind Speed Distribution

The main objective of this study is to estimate the optimum Weibull scale and shape parameters for wind speed distribution at three stations of the state of Tamil Nadu, India using Nelder-Mead, Broyden–Fletcher–Goldfarb–Shanno, and Simulated annealing optimization algorithms. An attempt has been made for the first time to apply these optimization algorithms to determine the optimum parameters. The study was conducted for long term wind speed data (38 years), short term wind speed data (5 years) and also with single year’s wind speed data to assess the performance of the algorithm for different quantum of data. The efficiency of these algorithms are analyzed using various statistical indicators like Root mean square error (RMSE), Correlation coefficient (R), Mean absolute error (MAE) and coefficient of determination (R2). The results suggest that the performance of three algorithms is similar irrespective of the quantum of the dataset. The estimated Weibull parameters are almost similar for short term and long term dataset. There is a marginal variation in the obtained parameters when only single year’s wind data is considered for the analysis. The Weibull probability distribution curve fits very well on the wind speed histogram when only single year’s wind speed data is considered and fits marginally well when short term and long term wind speed data is considered

scholarly journals The super-turbine wind power conversion paradox: using machine learning to reduce errors caused by Jensen's inequality

2019 ◽  
Vol 4 (2) ◽  
pp. 343-353 ◽  
Author(s):  
Tyler C. McCandless ◽  
Sue Ellen Haupt
Keyword(s):  
Machine Learning ◽  
Standard Deviation ◽  
Wind Speed ◽  
Wind Power ◽  
Power Conversion ◽  
Jensen’S Inequality ◽  
Jensen's Inequality ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Abstract. Wind power is a variable generation resource and therefore requires accurate forecasts to enable integration into the electric grid. Generally, the wind speed is forecast for a wind plant and the forecasted wind speed is converted to power to provide an estimate of the expected generating capacity of the plant. The average wind speed forecast for the plant is a function of the underlying meteorological phenomena being predicted; however, the wind speed for each turbine at the farm is also a function of the local terrain and the array orientation. Conversion algorithms that assume an average wind speed for the plant, i.e., the super-turbine power conversion, assume that the effects of the local terrain and array orientation are insignificant in producing variability in the wind speeds across the turbines at the farm. Here, we quantify the differences in converting wind speed to power at the turbine level compared with a super-turbine power conversion for a hypothetical wind farm of 100 2 MW turbines as well as from empirical data. The simulations with simulated turbines show a maximum difference of approximately 3 % at 11 m s−1 with a 1 m s−1 standard deviation of wind speeds and 8 % at 11 m s−1 with a 2 m s−1 standard deviation of wind speeds as a consequence of Jensen's inequality. The empirical analysis shows similar results with mean differences between converted wind speed to power and measured power of approximately 68 kW per 2 MW turbine. However, using a random forest machine learning method to convert to power reduces the error in the wind speed to power conversion when given the predictors that quantify the differences due to Jensen's inequality. These significant differences can lead to wind power forecasters overestimating the wind generation when utilizing a super-turbine power conversion for high wind speeds, and indicate that power conversion is more accurately done at the turbine level if no other compensatory mechanism is used to account for Jensen's inequality.

Sign in / Sign up

Export Citation Format

Share Document