scholarly journals A Finite Element Stress Analysis of Spur Gears Including Fillet Radii and Rim Thickness Effects

1983 ◽  
Vol 105 (3) ◽  
pp. 327-330 ◽  
Author(s):  
S. H. Chang ◽  
R. L. Huston ◽  
J. J. Coy
Keyword(s):  
Finite Element ◽  
Stress Analysis ◽  
Spur Gear ◽  
Root Surface ◽  
Spur Gears ◽  
Root Section ◽  
Finite Element Stress Analysis ◽  
Fillet Radius ◽  
Support Conditions ◽  
Maximum Stresses

Spur gear stress analysis results are presented for a variety of loading conditions, support conditions, fillet radii, and rim thickness. These results are obtained using the SAP IV finite-element code. The maximum stresses, occurring at the root surface, substantially increase with decreasing rim thickness for partially supported rims (that is, with loose-fitting hubs). For fully supported rims (that is, with tight-fitting hubs), the root surface stresses slightly decrease with decreasing rim thickness. The fillet radius is found to have a significant effect upon the maximum stresses at the root surface. These stresses increase with decreasing fillet radius. The fillet radius has little effect upon the internal root section stresses.

scholarly journals Finite Element Analysis of a Spur Gear Considering Mass Relief Strategies

2021 ◽  
Vol 31 (2) ◽  
pp. 36-49
Author(s):  
Lauro Miguel Lima Rocha ◽  
Marco Túlio Santana Alves
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Local Stress ◽  
Spur Gear ◽  
Spur Gears ◽  
Element Analysis ◽  
The Core ◽  
Core Thickness ◽  
Structural Influence ◽  
Maximum Stresses

This paper deals with analyzing the structural influence of mass reliefs in spur gears. For this purpose, a system composed of pinion and a gear was designed, such that for gear several geometries were designed with different reliefs shapes and soul thicknesses. From the proposed geometries, finite element analysis (FEA) was performed, and the tooth stresses of each model were compared with the solid gear. From the results, it was observed that the tooth stresses are reduced in some cases. Besides, from the aforementioned cases, it is possible to observe that the maximum stresses may take place in its core instead of the teeth (rim area). On the other hand, based on other cases, the core thickness plays an important role as a criterion that defines the local stress.

An Evaluation of Stresses and Deflection of Spur Gear Teeth Under Strain

1974 ◽  
Vol 96 (1) ◽  
pp. 85-93 ◽  
Author(s):  
G. Chabert ◽  
T. Dang Tran ◽  
R. Mathis
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Static Load ◽  
Simple Calculation ◽  
Spur Gear ◽  
Spur Gears ◽  
The Finite Element Method ◽  
Gear Teeth ◽  
Pressure Angle ◽  
Maximum Stresses

This paper aims at an evaluation of the stresses induced by a static load applied to gear teeth. For spur gears of different ratios with 20-deg pressure angle and standard addendum proportions, the stresses and deflections are computed by the finite element method. Formulas are drawn allowing a simple calculation of the maximum stresses, and the results are compared with what is given by ISO and AGMA standards related to the strength of gear teeth.

Stress Analysis of Tire Sections

1996 ◽  
Vol 24 (4) ◽  
pp. 349-366 ◽  
Author(s):  
T-M. Wang ◽  
I. M. Daniel ◽  
K. Huang
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Stress Analysis ◽  
Strain Analysis ◽  
Experimental Stress ◽  
Inflation Pressure ◽  
Substantial Agreement ◽  
Finite Element Stress Analysis ◽  
Strain Components ◽  
Fringe Patterns

Abstract An experimental stress-strain analysis by means of the Moiré method was conducted in the area of the tread and belt regions of tire sections. A special loading fixture was designed to support the tire section and load it in a manner simulating service loading and allowing for Moiré measurements. The specimen was loaded by imposing a uniform fixed deflection on the tread surface and increasing the internal pressure in steps. Moiré fringe patterns were recorded and analyzed to obtain strain components at various locations of interest. Maximum strains in the range of 1–7% were determined for an effective inflation pressure of 690 kPa (100 psi). These results were in substantial agreement with results obtained by a finite element stress analysis.

Improvement of a Lightweight Aluminium Cylinder Block Design Using Finite Element Stress Analysis

2020 ◽  
Vol 12 (05) ◽  
Author(s):  
Mohamad A Arsah ◽  
◽  
Syed M A Syed Mohd Yusoff Sobbry ◽  
Tengku N A Tuan Kamaruddin ◽  
Azmi Osman ◽  
...  
Keyword(s):  
Finite Element ◽  
Stress Analysis ◽  
Block Design ◽  
Cylinder Block ◽  
Finite Element Stress Analysis ◽  
Finite Element Stress
Sign in / Sign up

Export Citation Format

Share Document