Flow-Induced Instability of Heat-Exchanger Tubes due to Axial Flow in a Diffuser-Shaped, Loose Intermediate Support

1989 ◽  
Vol 111 (4) ◽  
pp. 428-434 ◽  
Author(s):  
A. Yasuo ◽  
M. P. Paidoussis
Keyword(s):  
Heat Exchanger ◽  
Fluid Dynamic ◽  
Axial Flow ◽  
Low Flow ◽  
Baffle Plate ◽  
Intermediate Point ◽  
Flow Passage ◽  
Fluid Forces ◽  
Dynamic Damping ◽  
Flow Velocities

In some heat exchangers and steam generators, the flow is predominantly axial, and the external fluid flows between baffled compartments through enlarged holes in the baffles around the heat exchanger tubes. Thus, the tube is subjected to relatively high flow velocities over small portions of its length, in the baffle locations. In this paper, the dynamics of such an idealized system is investigated, involving a cylindrical beam with pinned ends in axial flow, going through a baffle plate of finite thickness at some intermediate point, with small radial clearance. The fluid forces along the tube are formulated in a manner reminiscent of the transfer-matrix technique, since the character of these forces changes drastically along the tube. The fluid forces are determined approximately by means of potential flow theory, and viscous effects are taken into account only in a global sense. It was found that if the flow passage through the baffle plate is diffuser-shaped, negative fluid-dynamic damping is generated therein, destabilizing the system and leading to flutter at relatively low flow velocities. The instability depends critically on the shape of the hole through the baffle and on the clearance; thus a convergent-type flow passage does not lead to instability. The negative fluid-dynamic damping is linearly proportional to the flow velocity through the baffle.

Lift and Drag Characteristics of an Air-Cooled Heat Exchanger Axial Flow Fan

2015 ◽  
Vol 137 (8) ◽  
Author(s):  
Francois G. Louw ◽  
Theodore W. von Backström ◽  
Sybrand J. van der Spuy
Keyword(s):  
Heat Exchanger ◽  
Lift Coefficient ◽  
Axial Flow ◽  
Design Flow ◽  
Low Flow ◽  
Axial Fan ◽  
Flow Rates ◽  
Blade Element Theory ◽  
Lift And Drag ◽  
Air Cooled Heat Exchanger

Actuator-disk models (ADMs) use blade element theory to numerically simulate the flow field induced by axial fans. These models give a fair approximation at near design flow rates, but are of poor accuracy at low flow rates. Therefore, the lift/drag (LD) characteristics of two-dimensional (2D) sections along the span of an air-cooled heat exchanger (ACHE) axial fan are numerically investigated, with the future prospect of improving ADMs at these flow conditions. It is found that the blade sectional LD characteristics are similar in shape, but offset from the 2D LD characteristics of the reference airfoil (NASA LS 413 profile) at small angles of attack (αatt<5deg). A deviation between these characteristics is observed at higher angles of attack. The blade sectional lift coefficients for αatt>5deg always remain lower compared to the maximum lift coefficient of the reference airfoil. Conversely, the blade sectional drag coefficients are always higher compared to that of the reference airfoil for αatt>5deg.

Dynamics of a Free-Clamped Cylinder in Confined Axial Flow

2011 ◽  
Author(s):  
Stephanie Rinaldi ◽  
Michael P. Pai¨doussis
Keyword(s):  
Theoretical Model ◽  
Small Amplitude ◽  
Air Flow ◽  
Axial Flow ◽  
Low Flow ◽  
Quantitative Prediction ◽  
Oscillatory Behaviour ◽  
Observed Behaviour ◽  
Flow Velocities

The dynamics of a flexible cantilevered cylinder in confined axial flow is studied theoretically and experimentally, in the case where the flow is directed from the free end towards the clamped end. First, the dynamics is described, as observed in specially conducted experiments with air flow; the system developed small-amplitude first-mode vibrations at low flow velocities, which could be flutter, and at higher flows the oscillatory behaviour was succeeded by a static divergence. A simple, linear theoretical model is also developed, and the theoretically predicted behaviour is compared to the experimental one. The model captures the essentials of the observed behaviour, but requires improvement before quantitative prediction can be considered to be adequate.

The mechanisms underlying flow-induced instabilities of cylinder arrays in crossflow

1988 ◽  
Vol 187 ◽  
pp. 45-59 ◽  
Author(s):  
M. P. Paiudoussis ◽  
S. J. Price
Keyword(s):  
Degrees Of Freedom ◽  
Dynamic Theory ◽  
Fluid Dynamic ◽  
Dynamic Stiffness ◽  
Flexible Cylinder ◽  
System Parameters ◽  
Fluid Forces ◽  
Physical Mechanisms ◽  
Cylinder Arrays ◽  
Dynamic Damping

This paper aims to shed some light on the physical mechanisms involved in flowinduced instabilities of arrays of cylinders in crossflow. In the framework of quasi-steady fluid-dynamic theory, two distinct mechanisms are discussed. The first is similar but not identical to that associated with classical galloping; i.e. it is a negative fluid-dynamic damping mechanism and may obtain even if a single cylinder in the array is free to oscillate with only one degree of freedom. Unlike classical galloping, it is intimately related to the time delay experienced in the wake structure, and hence the fluid forces, adjusting to displacements of the cylinder. The second mechanism is similar to wake flutter; i.e. it is controlled by non-conservative fluid-dynamic stiffness effects and generally requires relative motion between adjacent cylinders in the array, although there is no reason why it should not occur for a single flexible cylinder with two degrees of freedom. The two mechanisms generally coexist, but each is predominant over different ranges of system parameters.

Neutrophil-dependent augmentation of PAF-induced vasoconstriction and albumin flux in coronary arterioles

1998 ◽  
Vol 275 (4) ◽  
pp. H1138-H1147 ◽  
Author(s):  
Qiaobing Huang ◽  
Mac Wu ◽  
Cynthia Meininger ◽  
Katherine Kelly ◽  
Yuan Yuan
Keyword(s):  
Platelet Activating Factor ◽  
Microvascular Dysfunction ◽  
Low Flow ◽  
Intercellular Adhesion Molecule ◽  
Neutrophil Adhesion ◽  
Intercellular Adhesion Molecule 1 ◽  
Apparent Permeability ◽  
Inflammatory Reactions ◽  
Coronary Arterioles ◽  
Flow Velocities

Platelet-activating factor (PAF) has been implicated in the pathogenesis of ischemic heart disease, reperfusion injury, and inflammatory reactions. Although neutrophils have been shown to primarily mediate PAF-induced microvascular dysfunction, the vasoactive effect of PAF and its neutrophil-dependent mechanism have not been directly and systematically studied in coronary resistance vessels. Therefore, the aim of this study was to examine the effects of PAF on coronary arteriolar function and neutrophil dynamics using an isolated and perfused microvessel preparation. Topical application of PAF to the vessels induced a dose-dependent decrease in the diameter but an increase in the apparent permeability coefficient of albumin. Disruption of the endothelium abolished the vasomotor response to PAF, and perfusion of neutrophils significantly augmented PAF-induced changes in vasomotor tone and permeability. Furthermore, the interaction between neutrophils and the endothelium was studied in the intact perfused coronary arterioles. Under control conditions, there were no adherent neutrophils observed in the vessels at varied intraluminal flow velocities. However, administration of PAF caused neutrophil adhesion to the endothelium of coronary arterioles at low flow velocities. Western blot analysis indicated that PAF upregulated the expression of intercellular adhesion molecule-1 in cultured coronary microvascular endothelial cells. Taken together, the results suggest that 1) PAF induces vasoconstriction and hyperpermeability in coronary arterioles via an endothelium-dependent and neutrophil-mediated mechanism, and 2) PAF is able to stimulate neutrophil adhesion in coronary arterioles under a condition of low flow rate.

The Dynamics of a Cantilevered Pipe Aspirating Fluid Studied by Experimental, Numerical and Analytical Methods

2010 ◽  
Author(s):  
Dana Giacobbi ◽  
Stephanie Rinaldi ◽  
Christian Semler ◽  
Michael P. Pai¨doussis
Keyword(s):  
Analytical Model ◽  
Low Flow ◽  
Computational Fluid Dynamics Cfd ◽  
Computational Structural Mechanics ◽  
Cantilevered Pipe ◽  
The Galerkin Method ◽  
Csm Model ◽  
Ocean Mining ◽  
Flow Experiments ◽  
Flow Velocities

This paper investigates the dynamics of a slender, flexible, aspirating cantilevered pipe, ingesting fluid at its free end and conveying it towards its clamped end. The problem is interesting not only from a fundamental perspective, but also because applications exist, notably in ocean mining [1]. First, the need for the present work is demonstrated through a review of previous research into the topic — spanning many years and yielding often contradictory results — most recently concluding that the system loses stability by flutter at relatively low flow velocities [2]. In the current paper, that conclusion is refined and expanded upon by exploring the problem in three ways: experimentally, numerically and analytically. First, air-flow experiments, in which the flow velocity of the fluid was varied and the frequency and amplitude of oscillation of the pipe were measured, were conducted using different elastomer pipes and intake shapes. Second, a fully-coupled Computational Fluid Dynamics (CFD) and Computational Structural Mechanics (CSM) model was developed in ANSYS in order to simulate experiments and corroborate experimental results. Finally, using an analytical approach, the existing linear equation of motion describing the system was significantly improved upon, and then solved via the Galerkin method in order to determine its stability characteristics. Heavily influenced by a CFD analysis, the proposed analytical model is different from previous ones, most notably because of the inclusion of a two-part fluid depressurization at the intake. In general, both the actual and numerical experiments suggest a first-mode loss of stability by flutter at relatively low flow velocities, which agrees with the results from the new analytical model.

Analisis Perbandingan Jenis Material Penukar Kalor Plat Datar Aliran Silang Untuk Proses Pengeringan Kayu

2021 ◽  
Vol 9 (1) ◽  
pp. 60-71
Author(s):  
Abeth Novria Sonjaya ◽  
Marhaenanto Marhaenanto ◽  
Mokhamad Eka Faiq ◽  
La Ode M Firman
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Flat Plate ◽  
Heat Exchangers ◽  
Fluid Dynamic ◽  
Cross Flow ◽  
Plate Heat ◽  
Dry Air ◽  
Copper Material ◽  
Plate Type

The processed wood industry urgently needs a dryer to improve the quality of its production. One of the important components in a dryer is a heat exchanger. To support a durable heat transfer process, a superior material is needed. The aim of the study was to analyze the effectiveness of the application of cross-flow flat plate heat exchangers to be used in wood dryers and compare the materials used and simulate heat transfer on cross-flow flat plate heat exchangers using Computational Fluid Dynamic simulations. The results showed that there was a variation in the temperature out of dry air and gas on the flat plate heat exchanger and copper material had a better heat delivery by reaching the temperature out of dry air and gas on the flat plate type heat exchanger of successive cross flow and.   overall heat transfer coefficient value and the effectiveness value of the heat exchanger of the heat transfer characteristics that occur with the cross-flow flat plate type heat exchanger in copper material of 251.74725 W/K and 0.25.

scholarly journals Expanded Microchannel Heat Exchanger: Finite Difference Modeling

Designs ◽  
2021 ◽  
Vol 5 (4) ◽  
pp. 58
Author(s):  
David Denkenberger ◽  
Joshua M. Pearce ◽  
Michael Brandemuehl ◽  
Mitchell Alverts ◽  
John Zhai
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Finite Difference ◽  
Flow Rate ◽  
Experimental Results ◽  
Low Flow ◽  
Difference Model ◽  
The Core ◽  
Finite Difference Model ◽  
Flow Maldistribution

A finite difference model of a heat exchanger (HX) considered maldistribution, axial conduction, heat leak, and the edge effect, all of which are needed to model a high effectiveness HX. An HX prototype was developed, and channel height data were obtained using a computerized tomography (CT) scan from previous work along with experimental results. This study used the core geometry data to model results with the finite difference model, and compared the modeled and experimental results to help improve the expanded microchannel HX (EMHX) prototype design. The root mean square (RMS) error was 3.8%. Manifold geometries were not put into the model because the data were not available, so impacts of the manifold were investigated by varying the temperature conditions at the inlet and exit of the core. Previous studies have not considered the influence of heat transfer in the manifold on the HX effectiveness when maldistribution is present. With no flow maldistribution, manifold heat transfer increases overall effectiveness roughly as would be expected by the greater heat transfer area in the manifolds. Manifold heat transfer coupled with flow maldistribution for the prototype, however, causes a decrease in the effectiveness at high flow rate, and an increase in effectiveness at low flow rate.

scholarly journals Temperature and Velocity Effects on Mass and Momentum Transport in Spacer-Filled Channels for Reverse Electrodialysis: A Numerical Study

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 2028 ◽  
Author(s):  
Zohreh Jalili ◽  
Jon Pharoah ◽  
Odne Stokke Burheim ◽  
Kristian Einarsrud
Keyword(s):  
Mass Transfer ◽  
Pressure Drop ◽  
Concentration Polarization ◽  
Numerical Study ◽  
Membrane Surface ◽  
Lower Pressure ◽  
Low Flow ◽  
Fluid Temperature ◽  
Reverse Electrodialysis ◽  
Flow Velocities

Concentration polarization is one of the main challenges of membrane-based processes such as power generation by reverse electrodialysis. Spacers in the compartments can enhance mass transfer by reducing concentration polarization. Active spacers increase the available membrane surface area, thus avoiding the shadow effect introduced by inactive spacers. Optimizing the spacer-filled channels is crucial for improving mass transfer while maintaining reasonable pressure losses. The main objective of this work was to develop a numerical model based upon the Navier–Stokes and Nernst–Planck equations in OpenFOAM, for detailed investigation of mass transfer efficiency and pressure drop. The model is utilized in different spacer-filled geometries for varying Reynolds numbers, spacer conductivity and fluid temperature. Triangular corrugations are found to be the optimum geometry, particularly at low flow velocities. Cylindrical corrugations are better at high flow velocities due to lower pressure drop. Enhanced mass transfer and lower pressure drop by elevating temperature is demonstrated.

Sign in / Sign up

Export Citation Format

Share Document