Results From Dynamic Tests and Analyses of a Medium Diameter LMFBR Piping System

1986 ◽  
Vol 108 (3) ◽  
pp. 330-333
Author(s):  
G. A. Schott ◽  
G. M. Hulbert ◽  
C. F. Heberling
Keyword(s):  
Seismic Design ◽  
Large Diameter ◽  
Piping System ◽  
Fast Breeder Reactor ◽  
Test Results ◽  
Dynamic Tests ◽  
Test Program ◽  
Piping Systems ◽  
Seismic Tests ◽  
Medium Diameter

This paper presents results and observations from dynamic tests and analyses performed on an 8-in. (0.20-m) diameter, thin-walled piping system. The piping system is a scaled representation of a Liquid Metal Fast Breeder Reactor (LMFBR) large diameter piping loop. Prototypic piping restraints were employed, including mechanical snubbers, rigid struts, pipe hangers and nonintegral pipe clamps. Snap-back, sine-sweep and seismic tests were performed for various restraint configurations and piping conditions. The test results are compared to analytical predictions for verification of the methods and models used in the seismic design of LMFBR piping systems. Test program conclusions and general recommendations for piping seismic analyses are presented along with a discussion of test and analysis results.

Seismic Proving Test of Ultimate Piping Strength: Test Results on Piping Component and Simplified Piping System

2002 ◽  
Author(s):  
Kenichi Suzuki ◽  
Y. Namita ◽  
H. Abe ◽  
I. Ichihashi ◽  
Kohei Suzuki ◽  
...  
Keyword(s):  
Large Scale ◽  
Safety Margin ◽  
Current Status ◽  
Piping System ◽  
Test Results ◽  
Seismic Safety ◽  
System A ◽  
Seismic Design Code ◽  
Piping Systems ◽  
Technical Issues

In 1998FY, the 6 year program of piping tests was initiated with the following objectives: i) to clarify the elasto-plastic response and ultimate strength of nuclear piping, ii) to ascertain the seismic safety margin of the current seismic design code for piping, and iii) to assess new allowable stress rules. In order to resolve extensive technical issues before proceeding on to the seismic proving test of a large-scale piping system, a series of preliminary tests of materials, piping components and simplified piping systems is intended. In this paper, the current status of the piping component tests and the simplified piping system tests is reported with focus on fatigue damage evaluation under large seismic loading.

Main Issues on the Seismic Design of Industrial Piping Systems and Components

2013 ◽  
Author(s):  
Fabrizio Paolacci ◽  
Md. Shahin Reza ◽  
Oreste S. Bursi ◽  
Arnold M. Gresnigt ◽  
Anil Kumar
Keyword(s):  
Seismic Design ◽  
Seismic Analysis ◽  
Experimental Investigations ◽  
Piping System ◽  
Analysis And Design ◽  
Correct Definition ◽  
Component Design ◽  
Piping Systems ◽  
Current Design ◽  
Bolted Flange

A significant number of damages in piping systems and components during recent seismic events have been reported in literature which calls for a proper seismic design of these structures. Nevertheless, there exists an inadequacy of proper seismic analysis and design rules for a piping system and its components. Current seismic design Codes are found to be over conservative and some components, e.g., bolted flange joints, do not have guidelines for their seismic design. Along this line, this paper discusses about the main issues on the seismic analysis and design of industrial piping systems and components. Initially, seismic analysis and component design of refinery piping systems are described. A review of current design approaches suggested by European (EN13480:3) and American (ASME B31.3) Codes is performed through a Case Study on a piping system. Some limits of available Codes are identified and a number of critical aspects of the problem e.g., dynamic interaction between pipes and rack, correct definition of the response factor and strain versus stress approach, are illustrated. Finally, seismic performance of bolted flange joints based on the results of experimental investigations carried out by the University of Trento, Italy, will be discussed.

Performance-Based Analysis of Coupled Support Structures and Piping Systems Subject to Seismic Loading

2015 ◽  
Author(s):  
Oreste S. Bursi ◽  
Fabrizio Paolacci ◽  
Md Shahin Reza
Keyword(s):  
Seismic Design ◽  
Seismic Analysis ◽  
Design Method ◽  
Design Guidelines ◽  
Piping System ◽  
Support Structures ◽  
Limit States ◽  
Piping Systems ◽  
Allowable Stress Design

The prevailing lack of proper and uniform seismic design guidelines for piping systems impels designers to follow standards conceived for other structures, such as buildings. The modern performance-based design approach is yet to be widely adopted for piping systems, while the allowable stress design method is still the customary practice. This paper presents a performance-based seismic analysis of petrochemical piping systems coupled with support structures through a case study. We start with a concept of performance-based analysis, followed by establishing a link between limit states and earthquake levels, exemplifying Eurocode and Italian prescriptions. A brief critical review on seismic design criteria of piping, including interactions between piping and support, is offered thereafter. Finally, to illustrate actual applications of the performance-based analysis, non-linear analyses on a realistic petrochemical piping system is performed to assess its seismic performance.

A Test and Analysis of the Multiple Support Piping Systems

1989 ◽  
Vol 111 (3) ◽  
pp. 291-299 ◽  
Author(s):  
T. Chiba ◽  
R. Koyanagi ◽  
N. Ogawa ◽  
C. Minowa
Keyword(s):  
Large Scale ◽  
Response Spectrum ◽  
Steel Structures ◽  
Response Spectra ◽  
Piping System ◽  
Multiple Response ◽  
Actual Behavior ◽  
Test Results ◽  
Piping Systems ◽  
Multiple Support

One of the current topics in the seismic design of piping systems is the overall reliability of them in earthquake events. Actual piping systems are generally supported by independent structures such as vessels and steel structures. So, it is very important to clarify the behavior of actual piping systems during the seismic events. For this purpose, the analytical method of multiple excitation problems is a preferable approach to not only evaluate the actual behavior of the piping systems, but also improve the reliability of piping systems. To clarify the dynamic characteristics of the piping systems and to assess the computational methods in the linear system subjected to multiple support excitations, an experimental study using a realistic large-scale piping model has been conducted. The equations for the multiple excitation problem have been validated and the adequacy of the multiple response spectra method has been confirmed by the comparison of the test results with the analytical one. This paper reports the results focusing on the analytical methods of the multiple support piping system. It is noted that the multiple response spectrum method is efficient for the multiple excitation problems.

Response Characteristics of Piping System Supported by Visco-Elastic and Elasto-Plastic Dampers

1990 ◽  
Vol 112 (1) ◽  
pp. 34-38 ◽  
Author(s):  
T. Chiba ◽  
H. Kobayashi
Keyword(s):  
Energy Dissipation ◽  
Seismic Design ◽  
Damping Ratio ◽  
The Other ◽  
Piping System ◽  
Response Level ◽  
Response Characteristics ◽  
Damping Effect ◽  
Component Test ◽  
Piping Systems

Improving the reliability of the piping systems can be achieved by eliminating the mechanical snubber and by reducing the response of the piping. In the seismic design of piping system, damping is one of the important parameters to reduce the seismic response. It is reported that the energy dissipation at piping supports contributes to increasing the damping ratio of piping system. Visco-elastic damper (VED) and elasto-plastic damper (EPD) were developed as more reliable, high-damping piping supports. The dynamic characteristics of these dampers were studied by the component test and the full-scale piping model test. Damping effect of VED is independent of the piping response and VED can be modeled as a complex spring in the dynamic analysis. On the other hand, damping ratio of piping system supported by EPD increases with the piping response level. So, these dampers are helpful to increase the damping ratio and to reduce the dynamic response of piping system.

Improvement of the Damping Constants for Seismic Design of Piping System for NPP

2002 ◽  
Author(s):  
Kei Kobayashi ◽  
Takashi Satoh ◽  
Nobuyuki Kojima ◽  
Kiyoshi Hattori ◽  
Masaki Nakagawa ◽  
...  
Keyword(s):  
Power Plant ◽  
Seismic Design ◽  
Nuclear Power ◽  
Power Plants ◽  
Estimation Method ◽  
Piping System ◽  
Piping Systems ◽  
Support Element ◽  
Present Design ◽  
Bolt Support

The present design damping constants for nuclear power plant (NPP)’s piping system in Japan were developed through discussion among expert researchers, electric utilities and power plant manufactures. They are standardized in “Technical guidelines for seismic design of Nuclear Power Plants” (JEAG 4601-1991 Supplemental Edition). But some of the damping constants are too conservative because of a lack of experimental data. To improve this excessive conservatism, piping systems supported by U-bolts were chosen and U-bolt support element test and piping model excitation test were performed to obtain proper damping constants. The damping mechanism consists of damping due to piping materials, damping due to fluid interaction, damping due to plastic deformation of piping and supports, and damping due to friction and collision between piping and supports. Because the damping due to friction and collision was considered to be dominant, we focused our effort on formulating these phenomena by a physical model. The validity of damping estimation method was confirmed by comparing data that was obtained from the elemental tests and the actual scale piping model test. New design damping constants were decided from the damping estimations for piping systems in an actual plant. From now on, we will use the new design damping constants for U-bolt support piping systems, which were proposed from this study, as a standard in the Japanese piping seismic design.

Applicability of Optimal Seismic Design Methodology for Piping Systems Subjected to Seismic Waves With Various Frequency Characteristics

2007 ◽  
Author(s):  
Tomohiro Ito ◽  
Katsuhisa Fujita ◽  
Masashi Michiue
Keyword(s):  
Seismic Design ◽  
Design Methodology ◽  
Seismic Waves ◽  
Structural Integrity ◽  
Frequency Characteristics ◽  
System Model ◽  
Piping System ◽  
Optimal Conditions ◽  
Piping Systems ◽  
Support Devices

In this study, the optimal seismic design methodology which can consider the structural integrity of both piping systems and elasto-plastic support devices are developed. This methodology employs genetic algorithm and can search the optimal conditions such as supporting locations, capacity and stiffness of supporting devices. A lead extrusion damper is treated here as a typical elasto-plastic damper. Numerical simulations are performed using a simple piping system model for the various kinds of seismic waves with different frequency characteristics. As a result, it is shown that the optimal seismic design methodology proposed here is applicable to the seismic design of piping systems supported by elasto-plastic dampers subjected to the seismic waves with various kinds of frequency characteristics.

Application of JSME Seismic Code Case by Elastic-Plastic Response Analysis to Practical Piping System

2018 ◽  
Author(s):  
Akihito Otani ◽  
Satoru Kai ◽  
Naoaki Kaneko ◽  
Tomoyoshi Watakabe ◽  
Masanori Ando ◽  
...  
Keyword(s):  
Seismic Design ◽  
Evaluation Methodology ◽  
Design Rule ◽  
Design Evaluation ◽  
Response Analysis ◽  
Piping System ◽  
Plastic Response ◽  
Seismic Code ◽  
Elastic Plastic ◽  
Piping Systems

A Code Case in the framework of JSME Nuclear Codes and Standards is being developed to incorporate a seismic design evaluation methodology for piping by means of advanced elastic-plastic response analysis methods and strain-based fatigue criteria. The Code Case as an alternative seismic design rule over the current rule will provide a more rational seismic design evaluation than the current criteria. This paper demonstrates an application result of the JSME Seismic Code Case to an actual complex piping system. The secondary coolant piping system of Japanese Fast Breeder Reactor, Monju, was selected as a representative of the complex piping systems. The elastic-plastic time history analysis for the piping system was performed and the piping system has been evaluated according to the JSME Seismic Code Case. The evaluation by the Code Case provides a reasonable result in terms of the piping fatigue evaluation that governs seismic integrity of piping systems. Moreover, it is found that the supporting forces and the response accelerations of the piping system obtained by the elastic-plastic response analysis also become more rational results than those with the current elastic response analysis. The contradiction of two requirements in piping design, flexibility for thermal expansion and rigidity for seismic response, can be effectively relaxed by use of the Code Case being developed.

Investigation of Method of Elasto-Plastic Analysis for Piping System Excited by Multi-Direction Input

2018 ◽  
Author(s):  
Takuro Kabaya ◽  
Nobuyuki Kojima ◽  
Masashi Arai ◽  
Satoru Hirouchi ◽  
Masatsugu Bando
Keyword(s):  
Ultimate Strength ◽  
Seismic Design ◽  
Strain Range ◽  
Plastic Behavior ◽  
Piping System ◽  
Japan Society ◽  
Analysis Method ◽  
The Past ◽  
Plastic Analysis ◽  
Piping Systems

This paper provides investigation on method of an elasto-plastic analysis for practical seismic design of nuclear piping systems, which are excited by multi-direction input. The Japan Society of Mechanical Engineers (JSME) established a task group to develop an elasto-plastic analysis method for nuclear piping systems, and prepared a case example code proposal for JSME.[1],[2] Our studies in past (ASME PVP2016-63186[3] and ASME PVP2017-65341[4]) were implemented on tests with unidirectional excitation using simple piping systems. In order to examine the applicability of the proposed case example code for JSME in piping of actual systems, it is necessary to examine cases in which there is multidirectional input excitation in piping systems in scales comparable to those of the piping in actual systems. We therefore conducted an analytical examination on demonstration of “the ultimate strength of piping system,” which was implemented at NUPEC. [5] We confirmed in the results of analytical examination that the strain range could be calculated at precision nearly equivalent to our examinations in the past, and that the draft code case was applicable. However, we also found a problem which needs to be solved. In addition, we were able to confirm that the local damping increase caused by the elasto-plastic behavior of the elbow which was subject to examination in this study was 1% or larger.

B31.1 Compliant Design of CFRP Buried Piping Systems

2015 ◽  
Author(s):  
Neda Stoeva ◽  
Timothy M. Adams ◽  
Tomas Jimenez ◽  
Scott Arnold ◽  
John Uhland
Keyword(s):  
Carbon Fiber ◽  
Composite System ◽  
Large Diameter ◽  
Material Behavior ◽  
Piping System ◽  
Service Water ◽  
Piping Systems ◽  
Cfrp Composite ◽  
Welded Pipe ◽  
Fiber Fabric

This paper presents the implementation of a Carbon Fiber Reinforced Polymer (CFRP) composite system as a long term replacement for a non-safety, non-seismic, non-QA, low pressure service water buried pipeline. The existing pipeline (to be replaced) consists of approximately 1800 feet of large diameter (primarily 54in.), carbon steel, spiral wound, seam welded pipe, which was built and installed using AWWA standards, but is maintained in accordance with the B31.1 Power Pipe Code [1]. The CFRP pipe installation is to be done as an internal repair, and designed to comply with ASME B31.1 as a stand-alone pipe (pressure boundary). In lieu of using the limited evaluation of PCC-2 [2], which is focused on local repairs; a complete design evaluation of the entire piping system to B31.1-2010 is conducted, which is consistent with and acceptable under PCC-2. Since B31.1 does not provide detailed guidance on the design of buried piping systems, the criteria presented in this paper use the base design requirements of B31.1 adjusted to include applied soil and surcharge loads. The selected CFRP repair is the TYFO® Fiberwrap® system which consists of a carbon fiber fabric (CFRP, TYFO SCH-41-2X), and glass fiber fabric (GFRP/dielectric barrier, TYFO SHE-51A), saturated with epoxy. This composite system is built up of unidirectional CFRP layers; thus, the presented design approach also considers anisotropic material behavior, and evaluates the hoop and axial loads and capacities separately. The criteria are presented for plants considering alternative repair and replacement techniques for buried and above ground non-safety pipes.

Sign in / Sign up

Export Citation Format

Share Document