Elastic Thermal Stresses in Bimetallic Pipe Welds

1980 ◽  
Vol 102 (4) ◽  
pp. 430-432 ◽  
Author(s):  
R. D. Blevins
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Intensity ◽  
Maximum Stress ◽  
Thermal Stresses ◽  
Simple Expression ◽  
Element Analysis ◽  
Maximum Stress Intensity ◽  
Bimetallic Pipe ◽  
Uniform Change

The elastic thermal stresses in a welded transition between two pipes of the same size but different alloys are explored. A stress-free temperature is postulated and the stress due to a uniform change in temperature is characterized by the maximum stress intensity in the weld. A simple expression for predicting this maximum stress intensity is developed based on the results of finite element analysis.

Bionic design of the tower for wind turbine

2021 ◽  
pp. 095440622110046
Author(s):  
Yuqiao Zheng ◽  
Fugang Dong ◽  
Huquan Guo ◽  
Bingxi Lu ◽  
Zhengwen He
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Maximum Stress ◽  
Natural Frequencies ◽  
Bionic Design ◽  
Analytic Hierarchy ◽  
Element Analysis ◽  
Maximum Deformation ◽  
Overall Stability ◽  
Biological Selection

The study obtains a methodology for the bionic design of the tower for wind turbines. To verify the rationality of the biological selection, the Analytic Hierarchy Procedure (AHP) is applied to calculate the similarity between the bamboo and the tower. Creatively, a bionic bamboo tower (BBT) is presented, which is equipped with four reinforcement ribs and five flanges. Further, finite element analysis is employed to comparatively investigate the performance of the BBT and the original tower (OT) in the static and dynamic. Through the investigation, it is suggested that the maximum deformation and maximum stress can be reduced by 5.93 and 13.75% of the BBT. Moreover, this approach results in 3% and 1.1% increase respectively in the First two natural frequencies and overall stability.

scholarly journals Mechanical Integrity Assessment of Two-Side Etched Type Printed Circuit Heat Exchanger with Additional Elliptical Channel

Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4711
Author(s):  
Armanto P. Simanjuntak ◽  
Jae-Young Lee
Keyword(s):  
Heat Exchanger ◽  
Stress Intensity ◽  
Maximum Stress ◽  
High Stress ◽  
Element Analysis ◽  
Integrity Assessment ◽  
Printed Circuit ◽  
Mechanical Integrity ◽  
Finite Element Analysis Simulation ◽  
Maximum Stress Intensity

Printed circuit heat exchangers (PCHEs) are often subject to high pressure and temperature difference between the hot and cold channels which may cause a mechanical integrity problem. A conventional plate heat exchanger where the channel geometries are semi-circular and etched at one side of the stacked plate is a common design in the market. However, the sharp edge tip channel may cause high stress intensity. Double-faced type PCHE appears with the promising ability to reduce the stress intensity and stress concentration factor. Finite element analysis simulation has been conducted to observe the mechanical integrity of double-etched printed circuit heat exchanger design. The application of an additional ellipse upper channel helps the stress intensity decrease in the proposed PCHE channel. Five different cases were simulated in this study. The simulation shows that the stress intensity was reduced up to 24% with the increase in additional elliptical channel radius. Besides that, the horizontal offset channels configuration was also investigated in this study. Simulation results show that the maximum stress intensity of 2.5 mm offset configuration is 9% lower compared to the maximum stress intensity of 0 mm offset. This work proposed an additional elliptical upper channel with a 2.5 mm offset configuration as an optimum design.

Finite Element Analysis of Thermal Stresses in Circumferential Cast Clasps of Removable Partial Dentures

2007 ◽  
Vol 23 ◽  
pp. 229-232
Author(s):  
Liliana Sandu ◽  
Nicolae Faur ◽  
Cristina Bortun ◽  
Sorin Porojan
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Stresses ◽  
Element Analysis ◽  
3 Dimensional ◽  
Thermal Changes ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Back Action ◽  
Aggressive Effect

Several studies evaluated the removable partial dentures by the finite element analysis, but none of them evaluated thermal stresses. The purpose of the study was to explore the influence of thermal oral changes induced by hot/cold liquids and food on the circumferential cast clasps of removable partial dentures. A 3-dimensional finite element method was used to explore the temperature distribution, thermal stress and the influence of thermal changes on stresses and displacements of circumferential clasps during functions. Thermal variations induce stresses in dental clasps, high temperatures having a more aggressive effect than lower one. Cold liquids and food induce high stresses in the retentive clasp arms while hot ones in the occlusal rests of the clasps and for the back action clasp also in the minor connector. The study suggests the importance of consFigureidering thermal variations for stress analyses of the cast clasps.

Three Turnaround Heat Treating Studies

2003 ◽  
Author(s):  
Jaan Taagepera ◽  
Marty Clift ◽  
D. Mike DeHart ◽  
Keneth Marden
Keyword(s):  
Heat Treatment ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Stress ◽  
Thermal Stresses ◽  
Heat Treating ◽  
Element Analysis ◽  
Stress Profiles ◽  
Insight Into

Three vessel modifications requiring heat treatment were analyzed prior to and during a planned turnaround at a refinery. One was a thick nozzle that required weld build up. This nozzle had been in hydrogen service and required bake-out to reduce the potential for cracking during the weld build up. Finite element analysis was used to study the thermal stresses involved in the bake-out. Another heat treatment studied was a PWHT of a nozzle replacement. The heat treatment band and temperature were varied with location in order to minimize cost and reduction in remaining strength of the vessel. Again, FEA was used to provide insight into the thermal stress profiles during heat treatment. The fmal heat treatment study was for inserting a new nozzle in a 1-1/4Cr-1/2Mo reactor. While this material would ordinarily require PWHT, the alteration was proposed to be installed without PWHT. Though accepted by the Jurisdiction, this nozzle installation was ultimately cancelled.

Thermal stresses in multilevel interconnections: Aluminum lines at different levels

1997 ◽  
Vol 12 (9) ◽  
pp. 2219-2222 ◽  
Author(s):  
Y-L. Shen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Stresses ◽  
Element Analysis ◽  
Future Studies ◽  
Level Lines ◽  
The Finite Element Analysis ◽  
Staggered Arrangement ◽  
Upper Level ◽  
Different Levels

Numerical results on the evolution of thermal stresses in multilevel interconnects are presented. Two levels of aluminum lines with an aspect ratio of unity, aligned vertically or arranged in a staggered manner, are considered by recourse to the finite element analysis. The stresses are found to be significantly higher in the lower-level lines than in the upper-level lines, for both the aligned and staggered arrangements. The stress magnitudes are generally smaller in lines of staggered arrangement, compared to the case of aligned lines. Implications of the present findings are discussed, with directions of future studies highlighted.

scholarly journals Finite Element Analysis of Needle Insertion Angle in Insulin Therapy

2019 ◽  
Vol 16 (4) ◽  
pp. 7512-7523
Author(s):  
Syakirah Mohamed Amin ◽  
Muhammad Hanif Ramlee ◽  
Hadafi Fitri Mohd Latip ◽  
Gan Hong Seng ◽  
Mohammed Rafiq Abdul Kadir
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Insulin Therapy ◽  
Maximum Stress ◽  
Three Dimensional ◽  
Needle Insertion ◽  
Stress And Strain ◽  
Medical Doctors ◽  
Element Analysis ◽  
Biomechanical Evaluation

Millions in the world suffering diabetes mellitus depends on insulin therapy to control their blood glucose level daily. However, the painful daily injections they need to take could lead to other complications if it is not done correctly. To date, it is suggested by many researchers and medical doctors that the needles should be inserted at any angles of 90º or 45º. Nevertheless, this recommendation has not been supported by clinical or biomechanical evaluation. Hence, this study evaluates the needle insertion for insulin therapy to find the favourable angles in order to reduce injury and pain onto the skin. Finite element analysis was done by  simulating the injection of three-dimensional (3D) needle model into a 3D skin model. The insertions were simulated at two different angles, which are 45ºand 90º with two different lengths of needles; 4 mm and 6 mm. This study concluded the favourable angle for 4 mm needle to be 90º while 6 mm needle was best to be inserted at 45º as these angles exerted the least maximum stress and strain onto the skin.

Sign in / Sign up

Export Citation Format

Share Document