Study of the Convective Heat Transfer in a Rotating Coolant Channel

1989 ◽  
Vol 111 (1) ◽  
pp. 43-50 ◽  
Author(s):  
J. Guidez
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Test Section ◽  
Suction Side ◽  
Turbine Rotor ◽  
Internal Cavity ◽  
Transfer Coefficients ◽  
Orthogonal Axis ◽  
Friction Forces

An experimental and theoretical study of convective heat transfer in a rotating coolant channel was inspired by the potential application to cooled turbine rotor blades. The flow that circulates into the internal cavity of the blade is subjected to Coriolis and centrifugal forces, in addition to pressure and friction forces. In this study, the channel is a rectangular-sectioned duct that rotates around an orthogonal axis. The experimental rig is composed of a vacuum enclosure, which includes an electric furnace, and the test section, heated by radiative flux. The temperatures of the wall test section are measured with thermocouples and the infrared pyrometer technique still under development. The convective heat transfer coefficients are determined with transient or steady-state techniques. It is shown that Coriolis acceleration has a beneficial influence on mean heat transfer. Locally, along the pressure side, the transfer increases strongly and on the contrary along the suction side, it decreases slightly. These effects are analyzed theoretically with a Navier-Stokes three dimensional (with mixing length model of turbulence) and explained by the influence of Coriolis force, which induces a secondary flow and distorts the velocity and temperature profiles. Experimental and theoretical results are presented and discussed.

Analysis of the Heat Transfer Driving Parameters in Tight Rotor Blade Tip Clearances

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Sergio Lavagnoli ◽  
Cis De Maesschalck ◽  
Guillermo Paniagua
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Wall Temperature ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Transfer Coefficients ◽  
Adiabatic Wall ◽  
Flow Parameters

Turbine rotor tips and casings are vulnerable to mechanical failures due to the extreme thermal loads they undergo during engine service. In addition to the heat flux variations during the engine transient operation, periodic unsteadiness occurs at every rotor passage, with amplitude dependent on the tip gap. The development of appropriate predictive tools and cooling schemes requires the precise understanding of the heat transfer mechanisms. The present paper analyses the nature of the overtip flow in transonic turbine rotors running at tight clearances and explores a methodology to determine the relevant flow parameters that model the heat transfer. Steady-state three-dimensional Reynolds-averaged Navier–Stokes (RANS) calculations were performed to simulate engine-like conditions considering two rotor tip gaps, 0.1% and 1%, of the blade span. At tight tip clearance, the adiabatic wall temperature is no longer independent of the solid thermal boundary conditions. The adiabatic wall temperature predicted with the linear Newton's cooling law was observed to rise to unphysical levels in certain regions within the rotor tip gap, resulting in unreliable convective heat transfer coefficients (HTCs). This paper investigates different approaches to estimate the relevant flow parameters that drive the heat transfer. A novel four-coefficient nonlinear cooling law is proposed to model the effects of temperature-dependent gas properties and of the heat transfer history. The four-parameter correlation provided reliable estimates of the convective heat transfer descriptors for the 1% tip clearance case, but failed to model the tip heat transfer of the 0.1% tip gap rotor. The present study allows experimentalists to retrieve information on the gap flow temperature and convective HTC based on the use of wall heat flux measurements. The use of nonlinear cooling laws is sought to improve the evaluation of the rotor heat transfer data while enhancing the understanding of tight-clearance overtip flows.

An Experimental Convective Heat Transfer Investigation Around a Film-Cooled Gas Turbine Blade

1990 ◽  
Vol 112 (3) ◽  
pp. 497-503 ◽  
Author(s):  
C. Camci ◽  
T. Arts
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Gas Turbine ◽  
Convective Heat ◽  
Free Stream ◽  
Weight Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Turbine Rotor ◽  
Free Stream Turbulence

The present paper deals with an experimental convective heat transfer investigation around a film-cooled, high-pressure gas turbine rotor blade mounted in a stationary, linear cascade arrangement. The measurements were performed in the von Karman Institute Isentropic Light Piston Compression Tube facility. The test blade was made of Macor glass ceramic and was instrumented with thin film gages. The coolant flow was ejected simultaneously through the leading edge (three rows of holes), the suction side (two rows of holes), and the pressure side (one row of holes). The effects of overall mass weight ratio, coolant to free-stream temperature ratio, and free-stream turbulence were successively investigated.

Sign in / Sign up

Export Citation Format

Share Document