Development of a High-Pressure-Ratio Axial Flow Compressor for a Medium-Size Gas Turbine

1986 ◽  
Vol 108 (2) ◽  
pp. 233-239 ◽  
Author(s):  
Y. Kashiwabara ◽  
Y. Matsuura ◽  
Y. Katoh ◽  
N. Hagiwara ◽  
T. Hattori ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Mechanical Design ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Axial Flow ◽  
Medium Size ◽  
High Pressure Ratio ◽  
Compressor Pressure Ratio ◽  
Predicted Values ◽  
Flow Compressor

In this paper, the development of a model 17-stage axial compressor (pressure ratio 14.7) for a medium-size gas turbine is described. The aerodynamic and mechanical design features of the compressor are presented. In advance of the full 17-stage test, the first three and nine stages were tested. Measured results confirm the design performance in the first stages of the 17-stage compressor. The details of the construction of the facilities, instrumentation and data acquisition system for the full 17-stage test are described. Test results for the 17-stage compressor are presented. The measured results are in good agreement with the predicted values.

scholarly journals Developments Leading to an Axial Flow Compressor for a 25 MW Class High Efficiency Gas Turbine

1990 ◽  
Author(s):  
Y. Kashiwabara ◽  
Y. Katoh ◽  
H. Ishii ◽  
T. Hattori ◽  
Y. Matsuura ◽  
...  
Keyword(s):  
Gas Turbine ◽  
High Efficiency ◽  
Mechanical Design ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Rotating Stall ◽  
Design Parameters ◽  
Axial Flow Compressor ◽  
Heavy Duty Gas Turbine ◽  
Flow Compressor

In this paper, the development leading to a 17-stage axial flow compressor (pressure ratio 14.7) for the 25 MW class heavy duty gas turbine H-25 is described. In the course of developing the H-25’s compressor, extensive measurements were carried out on models. Experimental results are compared with predicted values. Aerodynamic experiments covered the measurements of unsteady flows such as rotating stall and surge as well as the steady-state performance of the compressor. Based on the results of these tests, the aerodynamic and mechanical design parameters of the full scale H-25 compressor were finalized on the basis of two model compressors. Detailed measurements of the first unit of the H-25 gas turbine were carried out. Test results on the compressor are presented and show the achievement of the expected design targets.

Numerical Efforts of Aerodynamic Re-Design in a Single-Stage Transonic Axial Compressor: Part 1 — Stator Design

2017 ◽  
Author(s):  
Justin (Jongsik) Oh
Keyword(s):  
Pressure Ratio ◽  
Axial Compressor ◽  
Axial Flow ◽  
Single Stage ◽  
Design Flow ◽  
Design Parameters ◽  
Original Design ◽  
Circular Arc ◽  
Surge Margin ◽  
Flow Compressor

In many aerodynamic design parameters for the axial-flow compressor, three variables of tailored blading, blade lean and sweep were considered in the re-design efforts of a transonic single stage which had been designed in 1960’s NASA public domains. As Part 1, the re-design was limited to the stator vane only. For the original MCA (Multiple Circular Arc) blading, which had been applied at all radii, the CDA (Controlled Diffusion Airfoil) blading was introduced at midspan as the first variant, and the endwalls of hub and casing (or tip) were replaced with the DCA (Double Circular Arc) blading for the second variant. Aerodynamic performance was predicted through a series of CFD analysis at design speed, and the best aerodynamic improvement, in terms of pressure ratio/efficiency and operability, was found in the first variant of tailored blading. It was selected as a baseline for the next design efforts with blade lean, sweep and both combined. Among 12 variants, a case of positively and mildly leaned blades was found the most attractive one, relative to the original design, providing benefits of an 1.0% increase of pressure ratio at design flow, an 1.7% increase of efficiency at design flow, a 10.5% increase of the surge margin and a 32.3% increase of the choke margin.

Design and Development of a 12:1 Pressure Ratio Compressor for the Ruston 6-MW Gas Turbine

1982 ◽  
Author(s):  
F. Carchedi ◽  
G. R. Wood
Keyword(s):  
Gas Turbine ◽  
Test Data ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Aerodynamic Design ◽  
Design And Development ◽  
Surge Line ◽  
Flow Compressor ◽  
Industrial Gas Turbine ◽  
Spanwise Flow

This paper describes the design and development of a 15-stage axial flow compressor for a −6MW industrial gas turbine. Detailed aspects of the aerodynamic design are presented together with rig test data for the complete characteristic including stage data. Predictions of spanwise flow distributions are compared with measured values for the front stages of the compressor. Variable stagger stator blading is used to control the position of the low speed surge line and the effects of the stagger changes are discussed.

Investigation of an Axial Flow Compressor With Variable Reynolds Number and Inlet Casing Geometry

1978 ◽  
Author(s):  
B. Becker ◽  
O. von Schwerdtner ◽  
J. Günther
Keyword(s):  
Reynolds Number ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Flow Distribution ◽  
Pressure Level ◽  
Symmetric Flow ◽  
Flow Compressor ◽  
Gas Turbine Compressor ◽  
Theoretical Results

In the course of developing the compressor of a 100-MW gas turbine, extensive measurements took place on a test compressor provided with the four front stages scaled down to 1:4.63. The performance investigations have been supplemented by measurements of flow distribution down- and upstream of the blading, as well as at various intermediate axial positions. The test stand, operating in a closed circuit, allowed for the variation of the Reynolds number by changing the pressure level. The geometry of the inlet casing was variable as well, thus enabling the comparison of results with axial, two- and one-sided inlet flows. In this connection, the vibrational behavior of the rotating blades, besides the aerodynamics of the compressor, have been investigated. In case of the inlet casing with a two-sided inflow, additional flow field analyses have been performed using a model without compressor blading. The theoretical results calculated under the assumption of a rotational-symmetric flow, as well as the measurements at the gas turbine compressor itself, are used for comparison. The gas turbine compressor operating with a mass flow of 483 kg/s at ISO-conditions and a pressure ratio of 10 is running in the highest performance range of single-shaft compressors in operation today.

A simplified method for the deposition rate assessment on the vanes of a multistage axial-flow compressor

2021 ◽  
pp. 1-45
Author(s):  
Alessandro Vulpio ◽  
Alessio Suman ◽  
Nicola Casari ◽  
Michele Pinelli
Keyword(s):  
Particle Deposition ◽  
Axial Compressor ◽  
Axial Flow ◽  
Low Complexity ◽  
Economic Losses ◽  
Predicted Values ◽  
Flow Compressor ◽  
Particle Ingestion ◽  
Fouling Reduction ◽  
The Impact

Abstract Gas turbine particle ingestion may lead to the deposition of contaminants in the compressor section, inducing the performance losses of the whole engine. The economic losses derived from this issue push great interest in the investigation of such a phenomenon from a numerical and experimental standpoint. This paper describes a quantitative approach to predict particle deposition on the vanes of an axial compressor starting from the flow field obtained employing CFD simulations. The results are then compared to the experiments performed on the Allison 250 C18 compressor unit subject to particle ingestion under controlled conditions. The results derived from the experimental and numerical investigations are presented, providing insight into the mass deposited on the vanes and the corresponding zones most affected by the particle deposition issue. The numerical model showed good agreement in the estimation of the predicted values of the deposited mass and the corresponding patterns through the compressor stages. The low-complexity approach proposed here, helps the designer to predict the contamination of the stationary rows starting from a simple set of single-phase numerical results. Furthermore, with the implementation of this approach into the design path, the designer could reduce the impact of fouling, looking at the effects of their solutions under the fouling-reduction light.

Highly-Loaded Low-Reaction Boundary Layer Suction Axial Flow Compressor

2007 ◽  
Author(s):  
Songtao Wang ◽  
Xiaoqing Qiang ◽  
Weichun Lin ◽  
Guotai Feng ◽  
Zhongqi Wang
Keyword(s):  
Boundary Layer ◽  
High Pressure ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Design Concept ◽  
Axial Flow Compressor ◽  
Boundary Layer Suction ◽  
High Pressure Ratio ◽  
Flow Compressor ◽  
Highly Loaded

In order to design high pressure ratio and highly loaded axial flow compressor, a new design concept based on Highly-Loaded Low-Reaction and boundary layer suction was proposed in this paper. Then the concept’s characteristics were pointed out by comparing with the MIT’s boundary layer suction compressor. Also the application area of this design concept and its key technic were given out in this paper. Two applications were carried out in order to demonstrate the concept. The first application was to redesign a low speed duplication-stage axial flow compressor into a single stage. The second one was a feasibility analysis to decrease an 11 stage axial compressor’s stage count to 7 while not changing its aerodynamic performance. The analysis result showed that the new design concept is feasible and it can be used on high pressure stage of the aero-engine, compressor of ground gas turbine (except the transonic stage) and high total pressure ratio blower.

Design and Development of a 12:1 Pressure Ratio Compressor for the Ruston 6-MW Gas Turbine

1982 ◽  
Vol 104 (4) ◽  
pp. 823-831 ◽  
Author(s):  
F. Carchedi ◽  
G. R. Wood
Keyword(s):  
Gas Turbine ◽  
Test Data ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Aerodynamic Design ◽  
Design And Development ◽  
Surge Line ◽  
Flow Compressor ◽  
Industrial Gas Turbine ◽  
Spanwise Flow

The paper describes the design and development of a 15 stage axial flow compressor for a 6-MW industrial gas turbine. Detailed aspects of the aerodynamic design are presented together with rig test data for the complete characteristic including stage data. Predictions of spanwise flow distributions are compared with measured values for the front stages of the compressor. Variable stagger stator blading is used to control the position of the low-speed surge line and the effects of the stagger changes are discussed.

A New 1.7MW Industrial Gas Turbine: The Ruston Hurricane

1991 ◽  
Author(s):  
A. T. Sanders ◽  
M. H. Tothill ◽  
G. R. Wood
Keyword(s):  
Gas Turbine ◽  
High Efficiency ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Thermodynamic Efficiency ◽  
The Novel ◽  
Exhaust Temperature ◽  
High Pressure Ratio ◽  
Industrial Gas Turbine ◽  
Novel Design

The paper describes the design of a compact new 1.7MW (2300hp) single shaft industrial gas turbine and package, with high efficiency and exhaust temperature ideal for industrial congeneration applications. These advantages are obtained with a high pressure ratio single stage centrifugal compressor, single high temperature combustor and two-stage axial flow turbine using only one row of cooled blades. The novel design features are described with the associated development testing. A typical installation is also described showing the potential for very high overall thermodynamic efficiency.

On-Line Compressor Cascade Washing for Gas Turbine Performance Investigation

2011 ◽  
Author(s):  
Uyioghosa Igie ◽  
Pericles Pilidis ◽  
Dimitrios Fouflias ◽  
Ken Ramsden ◽  
Paul Lambart
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Flow ◽  
Engine Performance ◽  
Compressor Cascade ◽  
Design Point ◽  
Washing Process ◽  
On Line ◽  
Flow Compressor

On-line compressor washing for industrial gas turbine application is a promising method of mitigating the effects of compressor fouling degradation; however there are still few studies from actual engine experience that are inconclusive. In some cases the authors attribute this uncertainty as a result of other existing forms of degradation. The experimental approach applied here is one of the first of its kind, employing on-line washing on a compressor cascade and then relating the characteristics to a three-dimensional axial flow compressor. The overall performance of a 226MW engine model for the different cases of a clean, fouled and washed engine is obtained based on the changing compressor behavior. Investigating the effects of fouling on the clean engine exposed to blade roughness of 102μm caused 8.7% reduction in power at design point. This is equivalent, typically to 12 months degradation in fouling conditions. Decreases in mass flow, compressor efficiency, pressure ratio and unattainable design point speed are also observed. An optimistic recovery of 50% of the lost power is obtained after washing which lasts up to 10mins. Similarly, a recovery of all the key parameters is achieved. The study provides an insight into compressor cascade blade washing, which facilitates a reliable estimation of compressor overall efficiency penalties based on well established assumptions. Adopting Howell’s theory as well as constant polytropic efficiency, a general understanding of turbomachinery would judge that 50% of lost power recovered is likely to be the high end of what is achievable for the existing high pressure wash. This investigation highlights the obvious benefits of power recovery with on-line washing and the potential to maintain optimum engine performance with frequent washes. Clearly, the greatest benefits accrue when the washing process is initiated immediately following overhaul.

Design of the 6C Heavy-Duty Gas Turbine

2003 ◽  
Author(s):  
David Harper ◽  
Devin Martin ◽  
Harold Miller ◽  
Robert Grimley ◽  
Fre´de´ric Greiner
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
High Efficiency ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Load Test ◽  
Advanced Technology ◽  
General Electric ◽  
Three Stages ◽  
Flow Compressor

The MS6001C gas turbine combines the proven reliability of the General Electric gas turbine family with the advanced technology developed for the FA, FB and H machine designs. The engine configuration is a single shaft bolted rotor, driving a 50 or 60 Hz. generator though a cold end mounted load gear. Rated at 42.3 MW, with a thermal efficiency of 36.3%, the MS6001C will provide greater than a four percent increase in efficiency over the MS6001B. This paper is focused on the design and development of the MS6001C gas turbine, highlighting the commonality between this and other General Electric Power Systems (GEPS) and General Electric Aircraft Engines (GEAE) designs, as well as introducing some new and innovative features. The new high efficiency, 12 stage, axial flow compressor, features a 19:1 pressure ratio with three stages of variable guide vanes. The can annular, six chamber, Dry Low NOx (DLN-2.5H) combustion system is scaled from field proven, low emission technology. The turbine incorporates three stages, two cooled blade rows, and operates at a 1327°C firing temperature. After a thorough factory full speed no load test has been conducted, the first MS6001C engine will be shipped to a customer site in Kemalpasalzmir Turkey, where an instrumented full load test will be conducted to validate the design.

Sign in / Sign up

Export Citation Format

Share Document