Micro-Elastohydrodynamic Lubrication of an Elliptical Contact With Transverse and Three-Dimensional Sinusoidal Roughness

1989 ◽  
Vol 111 (4) ◽  
pp. 577-584 ◽  
Author(s):  
C. C. Kweh ◽  
H. P. Evans ◽  
R. W. Snidle
Keyword(s):  
Surface Roughness ◽  
High Temperature ◽  
High Speed ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Two Dimensional ◽  
Direction Transverse ◽  
Ehd Lubrication ◽  
Elliptical Contact

The paper describes the results of the analysis of elastohydrodynamic (EHD) lubrication of an elliptical contact between a rough, stationary surface and a smooth, moving surface. Roughness takes the form of sinusoidal grooves aligned in the direction transverse to that of lubricant entrainment. The conditions analyzed are chosen to correspond to the operating conditions of a high speed, high temperature disk machine. The main feature of the results is the almost complete flattening of the roughness that occurs, accompanied by a corresponding ripple in the pressure distribution. A contact with three-dimensional roughness has also been analyzed, and this shows that in comparison with the two-dimensional case, the longitudinal grooves tend to persist.

A Study of Spike and Modal Stall Phenomena in a Low-Speed Axial Compressor

1997 ◽  
Author(s):  
T. R. Camp ◽  
I. J. Day
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Two Dimensional ◽  
Stability Criteria ◽  
Stall Inception ◽  
Low Speed ◽  
The Stability ◽  
Dimensional Instability

This paper presents a study of stall inception mechanisms a in low-speed axial compressor. Previous work has identified two common flow breakdown sequences, the first associated with a short lengthscale disturbance known as a ‘spike’, and the second with a longer lengthscale disturbance known as a ‘modal oscillation’. In this paper the physical differences between these two mechanisms are illustrated with detailed measurements. Experimental results are also presented which relate the occurrence of the two stalling mechanisms to the operating conditions of the compressor. It is shown that the stability criteria for the two disturbances are different: long lengthscale disturbances are related to a two-dimensional instability of the whole compression system, while short lengthscale disturbances indicate a three-dimensional breakdown of the flow-field associated with high rotor incidence angles. Based on the experimental measurements, a simple model is proposed which explains the type of stall inception pattern observed in a particular compressor. Measurements from a single stage low-speed compressor and from a multistage high-speed compressor are presented in support of the model.

Numerical Solution of Mixed Thermal Elastohydrodynamic Lubrication in Point Contacts With Three-Dimensional Surface Roughness

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Xiaopeng Wang ◽  
Yuchuan Liu ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Three Dimensional ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Thickness Variation ◽  
Wide Range ◽  
Film Lubrication

Elastohydrodynamic lubrication (EHL) is a common mode of fluid-film lubrication in which many machine elements operate. Its thermal behavior is an important concern especially for components working under extreme conditions such as high speeds, heavy loads, and surfaces with significant roughness. Previous thermal EHL (TEHL) studies focused only on the cases with smooth surfaces under the full-film lubrication condition. The present study intends to develop a more realistic unified TEHL model for point contact problems that is capable of simulating the entire transition of lubrication status from the full-film and mixed lubrication all the way down to boundary lubrication with real machined roughness. The model consists of the generalized Reynolds equation, elasticity equation, film thickness equation, and those for lubricant rheology in combination with the energy equation for the lubricant film and the surface temperature equations. The solution algorithms based on the improved semi-system approach have demonstrated a good ability to achieve stable solutions with fast convergence under severe operating conditions. Lubricant film thickness variation and temperature rises in the lubricant film and on the surfaces during the entire transition have been investigated. It appears that this model can be used to predict mixed TEHL characteristics in a wide range of operating conditions with or without three-dimensional (3D) surface roughness involved. Therefore, it can be employed as a useful tool in engineering analyses.

Acoustic receptivity and evolution of two-dimensional and oblique disturbances in a Blasius boundary layer

2001 ◽  
Vol 432 ◽  
pp. 69-90 ◽  
Author(s):  
RUDOLPH A. KING ◽  
KENNETH S. BREUER
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Acoustic Wave ◽  
Three Dimensional ◽  
Two Dimensional ◽  
Surface Waviness ◽  
S Wave ◽  
Boundary Layer Instability ◽  
Blasius Boundary Layer ◽  
Tollmien Schlichting

An experimental investigation was conducted to examine acoustic receptivity and subsequent boundary-layer instability evolution for a Blasius boundary layer formed on a flat plate in the presence of two-dimensional and oblique (three-dimensional) surface waviness. The effect of the non-localized surface roughness geometry and acoustic wave amplitude on the receptivity process was explored. The surface roughness had a well-defined wavenumber spectrum with fundamental wavenumber kw. A planar downstream-travelling acoustic wave was created to temporally excite the flow near the resonance frequency of an unstable eigenmode corresponding to kts = kw. The range of acoustic forcing levels, ε, and roughness heights, Δh, examined resulted in a linear dependence of receptivity coefficients; however, the larger values of the forcing combination εΔh resulted in subsequent nonlinear development of the Tollmien–Schlichting (T–S) wave. This study provides the first experimental evidence of a marked increase in the receptivity coefficient with increasing obliqueness of the surface waviness in excellent agreement with theory. Detuning of the two-dimensional and oblique disturbances was investigated by varying the streamwise wall-roughness wavenumber αw and measuring the T–S response. For the configuration where laminar-to-turbulent breakdown occurred, the breakdown process was found to be dominated by energy at the fundamental and harmonic frequencies, indicative of K-type breakdown.

Simulation of Plasto-Elastohydrodynamic Lubrication in Line Contacts of Infinite and Finite Length

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Tao He ◽  
Jiaxu Wang ◽  
Zhanjiang Wang ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Finite Length ◽  
3D Model ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Axial Direction ◽  
Contact Length ◽  
Line Contact ◽  
Line Contacts ◽  
3D Surface Topography

Line contact is common in many machine components, such as various gears, roller and needle bearings, and cams and followers. Traditionally, line contact is modeled as a two-dimensional (2D) problem when the surfaces are assumed to be smooth or treated stochastically. In reality, however, surface roughness is usually three-dimensional (3D) in nature, so that a 3D model is needed when analyzing contact and lubrication deterministically. Moreover, contact length is often finite, and realistic geometry may possibly include a crowning in the axial direction and round corners or chamfers at two ends. In the present study, plasto-elastohydrodynamic lubrication (PEHL) simulations for line contacts of both infinite and finite length have been conducted, taking into account the effects of surface roughness and possible plastic deformation, with a 3D model that is needed when taking into account the realistic contact geometry and the 3D surface topography. With this newly developed PEHL model, numerical cases are analyzed in order to reveal the PEHL characteristics in different types of line contact.

Transient Analysis of a Ceramic High Temperature Heat Exchanger and Chemical Decomposer

2007 ◽  
Author(s):  
Valery Ponyavin ◽  
Taha Mohamed ◽  
Mohamed Trabia ◽  
Yitung Chen ◽  
Anthony E. Hechanova
Keyword(s):  
Steady State ◽  
High Temperature ◽  
Heat Exchanger ◽  
Thermal Stresses ◽  
Three Dimensional ◽  
Failure Criteria ◽  
Operating Conditions ◽  
Finite Element Software ◽  
Micro Channels ◽  
Temperature Heat

Ceramics are suitable for use in high temperature applications as well as corrosive environment. These characteristics were the reason behind selection silicone carbide for a high temperature heat exchanger and chemical decomposer, which is a part of the Sulphur-Iodine (SI) thermo-chemical cycle. The heat exchanger is expected to operate in the range of 950°C. The proposed design is manufactured using fused ceramic layers that allow creation of micro-channels with dimensions below one millimeter. A proper design of the heat exchanges requires considering possibilities of failure due to stresses under both steady state and transient conditions. Temperature gradients within the heat exchanger ceramic components induce thermal stresses that dominate other stresses. A three-dimensional computational model is developed to investigate the fluid flow, heat transfer and stresses in the decomposer. Temperature distribution in the solid is imported to finite element software and used with pressure loads for stress analysis. The stress results are used to calculate probability of failure based on Weibull failure criteria. Earlier analysis showed that stress results at steady state operating conditions are satisfactory. The focus of this paper is to consider stresses that are induced during transient scenarios. In particular, the cases of startup and shutdown of the heat exchanger are considered. The paper presents an evaluation of the stresses in these two cases.

scholarly journals On the Two-Scale Modelling of Elastohydrodynamic Lubrication in Tilted-Pad Bearings

Lubricants ◽  
2018 ◽  
Vol 6 (3) ◽  
pp. 78 ◽  
Author(s):  
Gregory de Boer ◽  
Andreas Almqvist
Keyword(s):  
Surface Topography ◽  
Load Capacity ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Multiscale Methods ◽  
Operating Conditions ◽  
Real Surface ◽  
Micro Scale ◽  
Macro Scale ◽  
Heterogeneous Multiscale

A two-scale method for modelling the Elastohydrodynamic Lubrication (EHL) of tilted-pad bearings is derived and a range of solutions are presented. The method is developed from previous publications and is based on the Heterogeneous Multiscale Methods (HMM). It facilitates, by means of homogenization, incorporating the effects of surface topography in the analysis of tilted-pad bearings. New to this article is the investigation of three-dimensional bearings, including the effects of both ideal and real surface topographies, micro-cavitation, and the metamodeling procedure used in coupling the problem scales. Solutions for smooth bearing surfaces, and under pure hydrodynamic operating conditions, obtained with the present two-scale EHL model, demonstrate equivalence to those obtained from well-established homogenization methods. Solutions obtained for elastohydrodynamic operating conditions, show a dependency of the solution to the pad thickness and load capacity of the bearing. More precisely, the response for the real surface topography was found to be stiffer in comparison to the ideal. Micro-scale results demonstrate periodicity of the flow and surface topography and this is consistent with the requirements of the HMM. The means of selecting micro-scale simulations based on intermediate macro-scale solutions, in the metamodeling approach, was developed for larger dimensionality and subsequent calibration. An analysis of the present metamodeling approach indicates improved performance in comparison to previous studies.

A Starved Mixed Elastohydrodynamic Lubrication Model for the Prediction of Lubrication Performance, Friction and Flash Temperature With Arbitrary Entrainment Angle

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Wei Pu ◽  
Dong Zhu ◽  
Jiaxu Wang
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Industrial Applications ◽  
Operating Conditions ◽  
Flash Temperature ◽  
Machined Surface ◽  
Lubrication Performance ◽  
Wide Range ◽  
Starved Lubrication

In this study, a modified mixed lubrication model is developed with consideration of machined surface roughness, arbitrary entraining velocity angle, starvation, and cavitation. Model validation is executed by means of comparison between the obtained numerical results and the available starved elastohydrodynamic lubrication (EHL) data found from some previous studies. A comprehensive analysis for the effect of inlet oil supply condition on starvation and cavitation, mixed EHL characteristics, friction and flash temperature in elliptical contacts is conducted in a wide range of operating conditions. In addition, the influence of roughness orientation on film thickness and friction is discussed under different starved lubrication conditions. Obtained results reveal that inlet starvation leads to an obvious reduction of average film thickness and an increase in interasperity cavitation area due to surface roughness, which results in significant increment of asperity contacts, friction, and flash temperature. Besides, the effect of entrainment angle on film thickness will be weakened if the two surfaces operate under starved lubrication condition. Furthermore, the results show that the transverse roughness may yield thicker EHL films and lower friction than the isotropic and longitudinal if starvation is taken into account. Therefore, the starved mixed EHL model can be considered as a useful engineering tool for industrial applications.

scholarly journals Quasi-two-dimensional approximation for numerical simulation of flows in engine ducts

2019 ◽  
Author(s):  
V. Vlasenko ◽  
A. Shiryaeva
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Three Dimensional ◽  
Preliminary Design ◽  
Two Dimensional ◽  
Combustion Chambers ◽  
New Approach ◽  
One Dimensional ◽  
Dimensional Approximation ◽  
3D Flows

New quasi-two-dimensional (2.5D) approach to description of three-dimensional (3D) flows in ducts is proposed. It generalizes quasi-one-dimensional (quasi-1D, 1.5D) theories. Calculations are performed in the (x; y) plane, but variable width of duct in the z direction is taken into account. Derivation of 2.5D approximation equations is given. Tests for verification of 2.5D calculations are proposed. Parametrical 2.5D calculations of flow with hydrogen combustion in an elliptical combustor of a high-speed aircraft, investigated within HEXAFLY-INT international project, are described. Optimal scheme of fuel injection is found and explained. For one regime, 2.5D and 3D calculations are compared. The new approach is recommended for use during preliminary design of combustion chambers.

Influence of geometric parameters and operating conditions on the thermohydrodynamic behaviour of plain journal bearings

2000 ◽  
Vol 214 (5) ◽  
pp. 445-457 ◽  
Author(s):  
I Pierre ◽  
M Fillon
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Three Dimensional ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Thermal Dissipation ◽  
Radial Clearance ◽  
Geometric Factors ◽  
Essential Components ◽  
Mass Flowrate

Hydrodynamic journal bearings are essential components of high-speed machinery. In severe operating conditions, the thermal dissipation is not a negligible phenomenon. Therefore, a three-dimensional thermohydrodynamic (THD) analysis has been developed that includes lubricant rupture and re-formation phenomena by conserving the mass flowrate. Then, the predictions obtained with the proposed numerical model are validated by comparison with the measurements reported in the literature. The effects of various geometric factors (length, diameter and radial clearance) and operating conditions (rotational speed, applied load and lubricant) on the journal bearing behaviour are analysed and discussed in order to inform bearing designers. Thus, it can be predicted that the bearing performance obtained highly depends on operating conditions and geometric configuration.

Sign in / Sign up

Export Citation Format

Share Document